Hmm same problem again with two of my sites.
Only one of the two Wireguard VPN's are down. I have tried the following:
arno-iptables-firewall restart
service network restart
pppoe-restart
ip link set dev wg0 down & ip link set dev wg0 up

All to no avail. Any other ideas before I reboot?
PS there is no failover configured for this site so I don't think MTU is the 
issue.

Regards
Michael Knill

On 20/3/21, 2:09 pm, "Michael Knill" <michael.kn...@ipcsolutions.com.au> wrote:

    Thanks. Guess I will need to test it out.

    Regards
    Michael Knill

    On 20/3/21, 2:03 pm, "Lonnie Abelbeck" <li...@lonnie.abelbeck.com> wrote:

        While playing with the WG MTU, it seemed to work with only setting one 
end and the tunnel used the smallest, but I played it safe and set everything 
to 1340.

        It would be good to know what the precise answer is.

        Lonnie


        > On Mar 19, 2021, at 9:57 PM, Michael Knill 
<michael.kn...@ipcsolutions.com.au> wrote:
        > 
        > Thanks Lonnie.
        > 
        > PS I was just thinking (dangerous I know). I would need to set it on 
both ends so do you think there would there be any issues with different MTU's 
at each end?
        > Ultimately it would be the same eventually but there would be a 
migration period.
        > 
        > Regards
        > Michael Knill
        > 
        > On 20/3/21, 1:41 pm, "Lonnie Abelbeck" <li...@lonnie.abelbeck.com> 
wrote:
        > 
        >    I haven't seen any issues with a WG MTU of 1340, yet anyway.
        > 
        >    Lonnie
        > 
        > 
        >> On Mar 19, 2021, at 9:29 PM, Michael Knill 
<michael.kn...@ipcsolutions.com.au> wrote:
        >> 
        >> Thanks Lonnie
        >> 
        >> Hmm that may have something to do with it. Might also be when it 
fails over to 4G.
        >> As most of my VPN's carry voice only, I think a standard MTU of 1340 
for all my systems should be fine. What do you think?
        >> 
        >> Regards
        >> Michael Knill
        >> 
        >> On 20/3/21, 10:40 am, "Lonnie Abelbeck" <li...@lonnie.abelbeck.com> 
wrote:
        >> 
        >>   Hi Michael,
        >> 
        >>   I have not experienced anything like that, WireGuard connectivity 
is rock solid for me.
        >> 
        >>   I don't recall later WireGuard versions having any fixes for what 
you are describing.
        >> 
        >>   Just guessing, the standard MTU for WG is 1420 (1500-80), if you 
have a PPPoE connection with a MTU of 1492 you might try setting the WG MTU to 
1412 (1500-8-80) or lower to test.
        >> 
        >>   I'm testing a 4G-LTE/5G fixed wireless internet service from 
T-Mobile, they use Carrier Grade NAT (CGNAT) for IPv4 which lowers the MTU to 
1420 (just like WG) so WG needs a MTU setting of 1340 to work over the CGNAT or 
else it hangs.
        >> 
        >>   Lonnie
        >> 
        >> 
        >> 
        >> 
        >>> On Mar 19, 2021, at 3:42 PM, Michael Knill 
<michael.kn...@ipcsolutions.com.au> wrote:
        >>> 
        >>> Hi Group
        >>> 
        >>> Not sure if anyone else is experiencing this. I'm on 1.3.10 and all 
my systems connect via Wireguard VPN to both my softswitches.
        >>> Its generally all pretty stable but occasionally one of the VPN’s 
will be disconnected and I have tried everything I can think of to bring it 
back up but only a reboot has managed to do so at this stage.
        >>> Any ideas?
        >>> 
        >>> Regards
        >>> Michael Knill
        >>> _______________________________________________
        >>> Astlinux-users mailing list
        >>> Astlinux-users@lists.sourceforge.net
        >>> https://lists.sourceforge.net/lists/listinfo/astlinux-users
        >>> 
        >>> Donations to support AstLinux are graciously accepted via PayPal to 
pay...@krisk.org.
        >> 
        >> 
        >> 
        >>   _______________________________________________
        >>   Astlinux-users mailing list
        >>   Astlinux-users@lists.sourceforge.net
        >>   https://lists.sourceforge.net/lists/listinfo/astlinux-users
        >> 
        >>   Donations to support AstLinux are graciously accepted via PayPal 
to pay...@krisk.org.
        >> 
        >> 
        >> _______________________________________________
        >> Astlinux-users mailing list
        >> Astlinux-users@lists.sourceforge.net
        >> https://lists.sourceforge.net/lists/listinfo/astlinux-users
        >> 
        >> Donations to support AstLinux are graciously accepted via PayPal to 
pay...@krisk.org.
        > 
        > 
        > 
        >    _______________________________________________
        >    Astlinux-users mailing list
        >    Astlinux-users@lists.sourceforge.net
        >    https://lists.sourceforge.net/lists/listinfo/astlinux-users
        > 
        >    Donations to support AstLinux are graciously accepted via PayPal 
to pay...@krisk.org.
        > 
        > 
        > _______________________________________________
        > Astlinux-users mailing list
        > Astlinux-users@lists.sourceforge.net
        > https://lists.sourceforge.net/lists/listinfo/astlinux-users
        > 
        > Donations to support AstLinux are graciously accepted via PayPal to 
pay...@krisk.org.



        _______________________________________________
        Astlinux-users mailing list
        Astlinux-users@lists.sourceforge.net
        https://lists.sourceforge.net/lists/listinfo/astlinux-users

        Donations to support AstLinux are graciously accepted via PayPal to 
pay...@krisk.org.


    _______________________________________________
    Astlinux-users mailing list
    Astlinux-users@lists.sourceforge.net
    https://lists.sourceforge.net/lists/listinfo/astlinux-users

    Donations to support AstLinux are graciously accepted via PayPal to 
pay...@krisk.org.


_______________________________________________
Astlinux-users mailing list
Astlinux-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/astlinux-users

Donations to support AstLinux are graciously accepted via PayPal to 
pay...@krisk.org.

Reply via email to