OK, i think it's not supported now # iw phy phy0 interface add mp0 type mp mesh_id MeshNetwork # ifconfig mp0 up [ 289.502405] ath10k_pci 0003:01:00.0: 10.4 wmi init: vdevs: 16 peers: 528 ti d: 132 [ 289.510058] ath10k_pci 0003:01:00.0: msdu-desc: 1424 skid: 32 [ 289.604802] ath10k_pci 0003:01:00.0: must load driver with rawmode=1 to add m esh interfaces ifconfig: SIOCSIFFLAGS: Invalid argument
then, i tried insmod ath10k_core.ko with rawmode=1, i got probe fw fail log as following [ 350.779002] ath10k_pci 0003:01:00.0: rawmode = 1 requires support from firmwa re [ 350.786294] ath10k_pci 0003:01:00.0: fatal problem with firmware features: -2 2 [ 350.793575] ath10k_pci 0003:01:00.0: could not probe fw (-22) Jay 2016-07-09 10:57 GMT+08:00 Yu-Chieh <[email protected]>: > i have checked firmware firmware-5.bin_10.4.3.00063-1 on codeaurora > > regarding ram mode, i think it's not supported > <6>[232109.383248] ath10k_pci 0003:01:00.0: firmware ver 10.4.3.00063 > api 5 features no-p2p,peer-flow-ctrl crc32 a0d385ce > <6>[232110.836979] ath10k_pci 0003:01:00.0: board_file api 1 bmi_id > 1:1 crc32 77b2338a > <4>[232113.369117] ath10k_pci 0003:01:00.0: 10.4 wmi init: vdevs: 16 > peers: 528 tid: 132 > <4>[232113.376857] ath10k_pci 0003:01:00.0: msdu-desc: 1424 skid: 32 > <6>[232113.452238] ath10k_pci 0003:01:00.0: htt-ver 2.2 wmi-op 6 > htt-op 4 cal otp max-sta 512 raw 0 hwcrypto 1 > > regarding wmi_service, i have checked > /sys/kernel/debug/ieee80211/phy0/ath10k/wmi_services > WMI_SERVICE_MESH_11S - > WMI_SERVICE_MESH_NON_11S enabled > > Any one knows MESH_NON_11S ? > > Jay > > 2016-07-09 1:48 GMT+08:00 Peter Oh <[email protected]>: >> >> On 07/08/2016 10:15 AM, Yeoh Chun-Yeow wrote: >>> >>> Make sure the firmware has the raw mode feature bit enabled to support >>> mesh. >> >> In addition to that, you may check out wmi_services (cat >> /sys/kernel/debug/ieee80211/phyX/ath10k/wmi_services) if >> WMI_SERVICE_MESH_11S is set to enabled which means 11s mesh supported in >> native Wi-Fi mode. >> >>> --- >>> Chun-Yeow >>> >>> On Fri, Jul 8, 2016 at 12:52 PM, Yu-Chieh <[email protected]> wrote: >>>> >>>> Hi, >>>> >>>> Does anyone know if current firmware support mesh mode(802.11s) on 99x0? >>>> >>>> Best regards, >>>> >>>> Jay >>>> >>>> _______________________________________________ >>>> ath10k mailing list >>>> [email protected] >>>> http://lists.infradead.org/mailman/listinfo/ath10k >>> >>> >> Peter _______________________________________________ ath10k mailing list [email protected] http://lists.infradead.org/mailman/listinfo/ath10k
