Take a look on the firmware here for your hardware and see how: https://github.com/kvalo/ath10k-firmware
Regards, Chun-Yeow On Sat, Jul 9, 2016 at 11:25 AM, Yu-Chieh <[email protected]> wrote: > OK, i think it's not supported now > # iw phy phy0 interface add mp0 type mp mesh_id MeshNetwork > # ifconfig mp0 up > [ 289.502405] ath10k_pci 0003:01:00.0: 10.4 wmi init: vdevs: 16 peers: 528 > ti > d: 132 > [ 289.510058] ath10k_pci 0003:01:00.0: msdu-desc: 1424 skid: 32 > [ 289.604802] ath10k_pci 0003:01:00.0: must load driver with rawmode=1 to > add m > esh interfaces > ifconfig: SIOCSIFFLAGS: Invalid argument > > then, i tried insmod ath10k_core.ko with rawmode=1, i got probe fw > fail log as following > [ 350.779002] ath10k_pci 0003:01:00.0: rawmode = 1 requires support from > firmwa > re > [ 350.786294] ath10k_pci 0003:01:00.0: fatal problem with firmware features: > -2 > 2 > [ 350.793575] ath10k_pci 0003:01:00.0: could not probe fw (-22) > > Jay > > 2016-07-09 10:57 GMT+08:00 Yu-Chieh <[email protected]>: >> i have checked firmware firmware-5.bin_10.4.3.00063-1 on codeaurora >> >> regarding ram mode, i think it's not supported >> <6>[232109.383248] ath10k_pci 0003:01:00.0: firmware ver 10.4.3.00063 >> api 5 features no-p2p,peer-flow-ctrl crc32 a0d385ce >> <6>[232110.836979] ath10k_pci 0003:01:00.0: board_file api 1 bmi_id >> 1:1 crc32 77b2338a >> <4>[232113.369117] ath10k_pci 0003:01:00.0: 10.4 wmi init: vdevs: 16 >> peers: 528 tid: 132 >> <4>[232113.376857] ath10k_pci 0003:01:00.0: msdu-desc: 1424 skid: 32 >> <6>[232113.452238] ath10k_pci 0003:01:00.0: htt-ver 2.2 wmi-op 6 >> htt-op 4 cal otp max-sta 512 raw 0 hwcrypto 1 >> >> regarding wmi_service, i have checked >> /sys/kernel/debug/ieee80211/phy0/ath10k/wmi_services >> WMI_SERVICE_MESH_11S - >> WMI_SERVICE_MESH_NON_11S enabled >> >> Any one knows MESH_NON_11S ? >> >> Jay >> >> 2016-07-09 1:48 GMT+08:00 Peter Oh <[email protected]>: >>> >>> On 07/08/2016 10:15 AM, Yeoh Chun-Yeow wrote: >>>> >>>> Make sure the firmware has the raw mode feature bit enabled to support >>>> mesh. >>> >>> In addition to that, you may check out wmi_services (cat >>> /sys/kernel/debug/ieee80211/phyX/ath10k/wmi_services) if >>> WMI_SERVICE_MESH_11S is set to enabled which means 11s mesh supported in >>> native Wi-Fi mode. >>> >>>> --- >>>> Chun-Yeow >>>> >>>> On Fri, Jul 8, 2016 at 12:52 PM, Yu-Chieh <[email protected]> wrote: >>>>> >>>>> Hi, >>>>> >>>>> Does anyone know if current firmware support mesh mode(802.11s) on 99x0? >>>>> >>>>> Best regards, >>>>> >>>>> Jay >>>>> >>>>> _______________________________________________ >>>>> ath10k mailing list >>>>> [email protected] >>>>> http://lists.infradead.org/mailman/listinfo/ath10k >>>> >>>> >>> Peter _______________________________________________ ath10k mailing list [email protected] http://lists.infradead.org/mailman/listinfo/ath10k
