Sven Eckelmann <[email protected]> writes:
> On Monday, 25 February 2019 21:00:38 CET Sven Eckelmann wrote:
> [...]
>> Tested-by: Sven Eckelmann <[email protected]>
>>
>> Was tested on QCA988X with 10.2.4-1.0-00041
>
> I just wanted to test it with 802.11s setup on IPQ4019 with 10.4-3.5.3-00057
> and QCA9888 with 10.4-3.5.3-00053 (ath10k-firmware) and 10.4-3.6-00140
> (linux-firmware 2018-12-16-211de167) for both. But it looks like the firmware
> always crashes with and without this patch and 11s.
>
> [ 221.620803] ath10k_pci 0000:01:00.0: wmi command 36967 timeout,
> restarting hardware
> [ 221.744056] ieee80211 phy0: Hardware restart was requested
> [ 225.130829] ath10k_pci 0000:01:00.0: failed to receive control
> response completion, polling..
> [ 226.170824] ath10k_pci 0000:01:00.0: Service connect timeout
> [ 226.170871] ath10k_pci 0000:01:00.0: failed to connect htt (-110)
> [ 226.252248] ath10k_pci 0000:01:00.0: Could not init core: -110
>
> If i count correctly, this is WMI_10_4_GPIO_CONFIG_CMDID. Not really
> supported
> by upstream but it looks like there is an Openwrt private patch (not yet
> accepted upstream [1])
>
>
> package/kernel/mac80211/patches/ath/974-ath10k_add-LED-and-GPIO-controlling-support-for-various-chipsets.patch
>
>
> which I have now removed to fix this problem for me.
>
> The tests with 10.4-3.6-00140 and 10.4-3.5.3-* worked fine without this patch.
>
> @Kalle are you expecting that he resents the patch again or can you just
> append this information to the commit message? At least it looks at the
> moment
> like there will be no new patch in the near future. But the
> commit cd93b83ad92 ("ath10k: support for multicast rate control") is breaking
> real world setups.
I'm planning to apply this. I was not sure what you wanted to add to the
commit log but I changed to now what's below. Please let me know if you
want to change it.
ath10k: fix incorrect multicast/broadcast rate setting
Invalid rate code is sent to firmware when multicast rate value of 0 is
sent to driver indicating disabled case, causing broken mesh path.
so fix that.
Tested on QCA9984 with firmware 10.4-3.6.1-00827
Sven tested on IPQ4019 with 10.4-3.5.3-00057 and QCA9888 with
10.4-3.5.3-00053
(ath10k-firmware) and 10.4-3.6-00140 (linux-firmware 2018-12-16-211de167).
Fixes: cd93b83ad92 ("ath10k: support for multicast rate control")
Co-developed-by: Zhi Chen <[email protected]>
Signed-off-by: Zhi Chen <[email protected]>
Signed-off-by: Pradeep Kumar Chitrapu <[email protected]>
Tested-by: Sven Eckelmann <[email protected]>
Patchwork-Id: 10723033
Signed-off-by: Kalle Valo <[email protected]>
--
Kalle Valo
_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
