On Feb 4, 2008 10:51 PM, bruno randolf <[EMAIL PROTECTED]> wrote:
> On Monday 04 February 2008 11:53:20 Luis R. Rodriguez wrote:
> > Hardware encryption doesn't work yet so lets use software
> > encryption for now.
> >
> > Changes-licensed-under: 3-Clause-BSD
> >
> > Signed-off-by: Luis R. Rodriguez <[EMAIL PROTECTED]>
> > ---
> > drivers/net/wireless/ath5k/base.c | 4 +++-
> > 1 files changed, 3 insertions(+), 1 deletions(-)
> >
> > diff --git a/drivers/net/wireless/ath5k/base.c
> > b/drivers/net/wireless/ath5k/base.c index bfe6836..ef9655c 100644
> > --- a/drivers/net/wireless/ath5k/base.c
> > +++ b/drivers/net/wireless/ath5k/base.c
> > @@ -2922,7 +2922,9 @@ ath5k_set_key(struct ieee80211_hw *hw, enum
> > set_key_cmd cmd,
> >
> > switch(key->alg) {
> > case ALG_WEP:
> > - break;
> > + /* XXX: fix hardware encryption, its not working. For now
> > + * allow software encryption */
> > + /* break; */
> > case ALG_TKIP:
> > case ALG_CCMP:
> > return -EOPNOTSUPP;
>
>
> hi luis!
>
> does this actually work for you?
>
> (i still can't use WEP here, seems like a header padding problem (maybe?))
Yup, replying using a laptop on WEP 128-bit. My signal is crappy so it
had to try a few times. Below is the log in case it helps.
[82764.508000] ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 21 (level,
low) -> IRQ 16
[82764.508000] ath5k_pci 0000:02:00.0: registered as 'phy1'
[82764.544000] phy1: Selected rate control algorithm 'simple'
[82764.544000] ath5k phy1: Atheros AR5213A chip found (MAC: 0x59, PHY: 0x43)
[82764.544000] ath5k phy1: RF5112A multiband radio found (0x36)
[82765.040000] ADDRCONF(NETDEV_UP): wlan2: link is not ready
Unplug ethernet cable:
[82821.356000] e100: eth0: e100_watchdog: link down
[82826.372000] ADDRCONF(NETDEV_UP): wlan2: link is not ready
[82831.440000] ADDRCONF(NETDEV_UP): wlan2: link is not ready
[82836.616000] wlan2: Initial auth_alg=0
[82836.616000] wlan2: authenticate with AP 00:05:5d:fa:d6:cc
[82836.620000] wlan2: RX authentication from 00:05:5d:fa:d6:cc (alg=0
transaction=2 status=0)
[82836.620000] wlan2: authenticated
[82836.620000] wlan2: associate with AP 00:05:5d:fa:d6:cc
[82836.620000] wlan2: authentication frame received from
xx:xx:xx:xx:xx:xx, but not in authenticate state - ignored
[82836.624000] wlan2: authentication frame received from
xx:xx:xx:xx:xx:xx, but not in authenticate state - ignored
[82836.628000] wlan2: authentication frame received from
xx:xx:xx:xx:xx:xx, but not in authenticate state - ignored
[82836.632000] wlan2: authentication frame received from
xx:xx:xx:xx:xx:xx, but not in authenticate state - ignored
[82836.640000] wlan2: authentication frame received from
xx:xx:xx:xx:xx:xx, but not in authenticate state - ignored
[82836.820000] wlan2: associate with AP xx:xx:xx:xx:xx:xx
[82836.824000] wlan2: RX AssocResp from xx:xx:xx:xx:xx:xx (capab=0x411
status=0 aid=2)
[82836.824000] wlan2: associated
[82836.824000] wlan2: switched to long barker preamble (BSSID=xx:xx:xx:xx:xx:xx)
[82836.828000] ADDRCONF(NETDEV_CHANGE): wlan2: link becomes ready
[82836.832000] wlan2: association frame received from
xx:xx:xx:xx:xx:xx, but not in associate state - ignored
[82843.460000] wlan2: deauthenticate(reason=3)
[82861.204000] ADDRCONF(NETDEV_UP): wlan2: link is not ready
[82867.136000] wlan2: Initial auth_alg=0
[82867.136000] wlan2: authenticate with AP xx:xx:xx:xx:xx:xx
[82867.136000] wlan2: RX authentication from xx:xx:xx:xx:xx:xx (alg=0
transaction=2 status=0)
[82867.136000] wlan2: authenticated
[82867.136000] wlan2: associate with AP xx:xx:xx:xx:xx:xx
[82867.336000] wlan2: associate with AP xx:xx:xx:xx:xx:xx
[82867.352000] wlan2: RX AssocResp from xx:xx:xx:xx:xx:xx (capab=0x411
status=0 aid=2)
[82867.352000] wlan2: associated
[82867.352000] wlan2: switched to long barker preamble (BSSID=xx:xx:xx:xx:xx:xx)
[82867.352000] ADDRCONF(NETDEV_CHANGE): wlan2: link becomes ready
[82882.748000] wlan2: no IPv6 routers present
Luis
_______________________________________________
ath5k-devel mailing list
[email protected]
https://lists.ath5k.org/mailman/listinfo/ath5k-devel
