Tonight I went to where there is an access point I can use and tried
again. This PC and wireless card have worked before under Linux, but
I'm not sure if it was the same driver version. First I verified
that it would work under Windows. It did, although the signal is
weak and it would drop out sometimes. Then I tried
ifconfig wlan0 up, iwlist wlan0 scan, and iwconfig wlan0 essid any
(and essid auto and some other variations) Here is output from the
commands
wlan0 Link encap:Ethernet HWaddr 00:15:E9:D9:CC:B4
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
wlan0 Scan completed :
Cell 01 - Address: 00:18:39:C1:5A:3A
Channel:6
Frequency:2.437 GHz (Channel 6)
Quality=31/70 Signal level=-79 dBm
Encryption key:off
ESSID:"shutup!"
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s
24 Mb/s; 36 Mb/s; 54 Mb/s
Bit Rates:6 Mb/s; 9 Mb/s; 12 Mb/s; 48 Mb/s
Mode:Master
Extra:tsf=0000002ebb002187
Extra: Last beacon: 538ms ago
IE: Unknown: 000773687574757021
IE: Unknown: 010882848B962430486C
IE: Unknown: 030106
IE: Unknown: 2A0100
IE: Unknown: 2F0100
IE: Unknown: 32040C121860
IE: Unknown: DD06001018020304
Cell 02 - Address: 00:20:D8:03:C8:77
Channel:1
Frequency:2.412 GHz (Channel 1)
Quality=20/70 Signal level=-90 dBm
Encryption key:off
ESSID:"UA-WLAN"
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s
Mode:Master
Extra:tsf=00000184738ae18c
Extra: Last beacon: 952ms ago
IE: Unknown: 000755412D574C414E
IE: Unknown: 010482840B16
IE: Unknown: 030101
IE: Unknown: 050401050000
wlan0 IEEE 802.11bg ESSID:""
Mode:Managed Frequency:2.412 GHz Access Point: Not-Associated
Tx-Power=27 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
and here is the relevant portion of dmesg and lspci
serial_cs 1.0: firmware: requesting DP83903.cis
cfg80211: Calling CRDA to update world regulatory domain
cfg80211: World regulatory domain updated:
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
(2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
(2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
(5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
(5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
ath5k 0000:03:00.0: enabling device (0000 -> 0002)
ath5k 0000:03:00.0: PCI INT A -> Link[LNKD] -> GSI 11 (level, low) -> IRQ 11
ath5k 0000:03:00.0: registered as 'phy0'
Intel ICH Modem 0000:00:1f.6: PCI INT B -> Link[LNKB] -> GSI 5 (level, low) ->
IRQ 5
Intel ICH Modem 0000:00:1f.6: setting latency timer to 64
Intel ICH 0000:00:1f.5: PCI INT B -> Link[LNKB] -> GSI 5 (level, low) -> IRQ 5
Intel ICH 0000:00:1f.5: setting latency timer to 64
ath: EEPROM regdomain: 0x10
ath: EEPROM indicates we should expect a direct regpair map
ath: Country alpha2 being used: CO
ath: Regpair used: 0x10
phy0: Selected rate control algorithm 'minstrel'
ath5k phy0: Atheros AR2414 chip found (MAC: 0x79, PHY: 0x45)
cfg80211: Calling CRDA for country: CO
cfg80211: Regulatory domain changed to country: CO
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
(5170000 KHz - 5250000 KHz @ 20000 KHz), (300 mBi, 1700 mBm)
(5250000 KHz - 5330000 KHz @ 20000 KHz), (300 mBi, 2300 mBm)
(5735000 KHz - 5835000 KHz @ 20000 KHz), (300 mBi, 3000 mBm)
cfg80211: Calling CRDA for country: US
cfg80211: Regulatory domain changed to country: US
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
(5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
(5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
(5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
(5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
(5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
intel8x0_measure_ac97_clock: measured 50456 usecs (2426 samples)
---
03:00.0 Ethernet controller: Atheros Communications Inc. Atheros AR5001X+
Wireless Network Adapter (rev 01)
Subsystem: D-Link System Inc Device 3a1a
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 168 (2500ns min, 7000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f4000000 (32-bit, non-prefetchable) [size=64K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=2 PME-
Kernel driver in use: ath5k
Kernel modules: ath5k
Then there is a new kernel for Fedora 12 in the last day or so, so I got
that and booted it up and tried again with the same lack of success
wlan0 Link encap:Ethernet HWaddr 00:15:E9:D9:CC:B4
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
wlan0 Scan completed :
Cell 01 - Address: 00:20:D8:03:C8:77
Channel:1
Frequency:2.412 GHz (Channel 1)
Quality=15/70 Signal level=-95 dBm
Encryption key:off
ESSID:"UA-WLAN"
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s
Mode:Master
Extra:tsf=000001854fd6337f
Extra: Last beacon: 1017ms ago
IE: Unknown: 000755412D574C414E
IE: Unknown: 010482840B16
IE: Unknown: 030101
IE: Unknown: 050400050000
Cell 02 - Address: 00:18:39:C1:5A:3A
Channel:6
Frequency:2.437 GHz (Channel 6)
Quality=32/70 Signal level=-78 dBm
Encryption key:off
ESSID:"shutup!"
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s
24 Mb/s; 36 Mb/s; 54 Mb/s
Bit Rates:6 Mb/s; 9 Mb/s; 12 Mb/s; 48 Mb/s
Mode:Master
Extra:tsf=0000002f974f81c3
Extra: Last beacon: 405ms ago
IE: Unknown: 000773687574757021
IE: Unknown: 010882848B962430486C
IE: Unknown: 030106
IE: Unknown: 2A0100
IE: Unknown: 2F0100
IE: Unknown: 32040C121860
IE: Unknown: DD06001018020304
cfg80211: Calling CRDA to update world regulatory domain
pcmcia_socket pcmcia_socket0: cs: IO port probe 0xa00-0xaff: clean.
ath5k 0000:03:00.0: enabling device (0000 -> 0002)
ath5k 0000:03:00.0: PCI INT A -> Link[LNKD] -> GSI 11 (level, low) -> IRQ 11
ath5k 0000:03:00.0: registered as 'phy0'
dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
Intel ICH 0000:00:1f.5: PCI INT B -> Link[LNKB] -> GSI 5 (level, low) -> IRQ 5
Intel ICH 0000:00:1f.5: setting latency timer to 64
cfg80211: World regulatory domain updated:
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
(2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
(2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
(5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
(5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
ath: EEPROM regdomain: 0x10
ath: EEPROM indicates we should expect a direct regpair map
ath: Country alpha2 being used: CO
ath: Regpair used: 0x10
name_count maxed, losing inode data: dev=00:07, inode=8851
name_count maxed, losing inode data: dev=00:07, inode=8851
name_count maxed, losing inode data: dev=00:07, inode=8851
name_count maxed, losing inode data: dev=00:07, inode=8851
name_count maxed, losing inode data: dev=00:07, inode=8851
name_count maxed, losing inode data: dev=00:07, inode=8851
name_count maxed, losing inode data: dev=00:07, inode=8851
name_count maxed, losing inode data: dev=00:07, inode=8851
name_count maxed, losing inode data: dev=00:07, inode=8851
name_count maxed, losing inode data: dev=00:07, inode=8851
name_count maxed, losing inode data: dev=00:07, inode=8851
name_count maxed, losing inode data: dev=00:07, inode=8851
name_count maxed, losing inode data: dev=00:07, inode=8866
name_count maxed, losing inode data: dev=00:07, inode=8866
name_count maxed, losing inode data: dev=00:07, inode=8866
name_count maxed, losing inode data: dev=00:07, inode=8866
name_count maxed, losing inode data: dev=00:07, inode=8866
name_count maxed, losing inode data: dev=00:07, inode=8866
name_count maxed, losing inode data: dev=00:07, inode=8866
name_count maxed, losing inode data: dev=00:07, inode=8866
name_count maxed, losing inode data: dev=00:07, inode=8866
name_count maxed, losing inode data: dev=00:07, inode=8866
name_count maxed, losing inode data: dev=00:07, inode=8866
name_count maxed, losing inode data: dev=00:07, inode=8866
name_count maxed, losing inode data: dev=00:07, inode=8866
name_count maxed, losing inode data: dev=00:07, inode=8851
name_count maxed, losing inode data: dev=00:07, inode=8890
phy0: Selected rate control algorithm 'minstrel'
name_count maxed, losing inode data: dev=00:07, inode=8851
name_count maxed, losing inode data: dev=00:07, inode=8892
name_count maxed, losing inode data: dev=00:07, inode=8892
name_count maxed, losing inode data: dev=00:07, inode=8892
name_count maxed, losing inode data: dev=00:07, inode=8892
name_count maxed, losing inode data: dev=00:07, inode=8892
name_count maxed, losing inode data: dev=00:07, inode=8892
ath5k phy0: Atheros AR2414 chip found (MAC: 0x79, PHY: 0x45)
cfg80211: Calling CRDA for country: CO
cfg80211: Regulatory domain changed to country: CO
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
(5170000 KHz - 5250000 KHz @ 20000 KHz), (300 mBi, 1700 mBm)
(5250000 KHz - 5330000 KHz @ 20000 KHz), (300 mBi, 2300 mBm)
(5735000 KHz - 5835000 KHz @ 20000 KHz), (300 mBi, 3000 mBm)
00:00.0 Host bridge: Intel Corporation 82830 830 Chipset Host Bridge (rev 04)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=256M]
Capabilities: [40] Vendor Specific Information: Len=05 <?>
Capabilities: [a0] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans-
64bit- FW+ AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x2
Kernel driver in use: agpgart-intel
00:01.0 PCI bridge: Intel Corporation 82830 830 Chipset AGP Bridge (rev 04)
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 32
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: fc000000-fdffffff
Prefetchable memory behind bridge: e0000000-e7ffffff
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
00:1d.0 USB Controller: Intel Corporation 82801CA/CAM USB Controller #1 (rev
02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Latitude C640
Physical Slot: 2
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 4: I/O ports at bf80 [size=32]
Kernel driver in use: uhci_hcd
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 42) (prog-if
00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=02, subordinate=10, sec-latency=32
I/O behind bridge: 0000e000-0000ffff
Memory behind bridge: f4000000-fbffffff
Prefetchable memory behind bridge: 28000000-31ffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
00:1f.0 ISA bridge: Intel Corporation 82801CAM ISA Bridge (LPC) (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Kernel modules: iTCO_wdt, intel-rng
00:1f.1 IDE interface: Intel Corporation 82801CAM IDE U100 Controller (rev 02)
(prog-if 8a [Master SecP PriP])
Subsystem: Intel Corporation Latitude C640
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at bfa0 [size=16]
Region 5: Memory at 32000000 (32-bit, non-prefetchable) [size=1K]
Kernel driver in use: ata_piix
00:1f.5 Multimedia audio controller: Intel Corporation 82801CA/CAM AC'97 Audio
Controller (rev 02)
Subsystem: Cirrus Logic Crystal WMD Audio Codec
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 5
Region 0: I/O ports at d800 [size=256]
Region 1: I/O ports at dc80 [size=64]
Kernel driver in use: Intel ICH
Kernel modules: snd-intel8x0
00:1f.6 Modem: Intel Corporation 82801CA/CAM AC'97 Modem Controller (rev 02)
(prog-if 00 [Generic])
Subsystem: PCTel Inc Dell Inspiron 2100 internal modem
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 5
Region 0: I/O ports at d400 [size=256]
Region 1: I/O ports at dc00 [size=128]
Kernel driver in use: Intel ICH Modem
Kernel modules: snd-intel8x0m
01:00.0 VGA compatible controller: ATI Technologies Inc Radeon Mobility M6 LY
(prog-if 00 [VGA controller])
Subsystem: Dell Device 00e3
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+ ParErr-
Stepping+ SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (2000ns min), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at c000 [size=256]
Region 2: Memory at fcff0000 (32-bit, non-prefetchable) [size=64K]
[virtual] Expansion ROM at fc000000 [disabled] [size=128K]
Capabilities: [58] AGP version 2.0
Status: RQ=48 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans-
64bit- FW- AGP3- Rate=x1,x2,x4
Command: RQ=32 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW-
Rate=x2
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: radeon
Kernel modules: radeon, radeonfb
02:00.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] (rev 78)
Subsystem: Dell Device 00e3
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (2500ns min, 2500ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at ec80 [size=128]
Region 1: Memory at f8fffc00 (32-bit, non-prefetchable) [size=128]
Expansion ROM at 30000000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=2 PME-
Kernel driver in use: 3c59x
Kernel modules: 3c59x
02:01.0 CardBus bridge: Texas Instruments PCI1420 PC card Cardbus Controller
Subsystem: Dell Device 00e3
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 168, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f8000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=02, secondary=03, subordinate=06, sec-latency=176
Memory window 0: 28000000-2bfff000 (prefetchable)
Memory window 1: f4000000-f7fff000
I/O window 0: 0000e000-0000e0ff
I/O window 1: 0000e400-0000e4ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt- PostWrite+
16-bit legacy interface ports at 0001
Kernel driver in use: yenta_cardbus
Kernel modules: yenta_socket
02:01.1 CardBus bridge: Texas Instruments PCI1420 PC card Cardbus Controller
Subsystem: Dell Device 00e3
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 168, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f8001000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=02, secondary=07, subordinate=0a, sec-latency=176
Memory window 0: 2c000000-2ffff000 (prefetchable)
Memory window 1: 34000000-37fff000
I/O window 0: 0000e800-0000e8ff
I/O window 1: 0000f000-0000f0ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
Kernel driver in use: yenta_cardbus
Kernel modules: yenta_socket
03:00.0 Ethernet controller: Atheros Communications Inc. Atheros AR5001X+
Wireless Network Adapter (rev 01)
Subsystem: D-Link System Inc Device 3a1a
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 168 (2500ns min, 7000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f4000000 (32-bit, non-prefetchable) [size=64K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=2 PME-
Kernel driver in use: ath5k
Kernel modules: ath5k
_______________________________________________
ath5k-users mailing list
ath5k-users@lists.ath5k.org
https://lists.ath5k.org/mailman/listinfo/ath5k-users
