Hi
I've got a problem with a broadcom 4312 [12e4:4315].
The environment :
===========================
uname -a
2.6.35.5-libre.29.fc14.x86_64
lspci -vnn
0b:00.0 Network controller [0280]: Broadcom Corporation BCM4312 802.11b/g
[14e4:4315] (rev 01)
Subsystem: Dell Wireless 1395 WLAN Mini-Card [1028:000b]
Flags: bus master, fast devsel, latency 0, IRQ 17
Memory at fe7fc000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [40] Power Management version 3
Capabilities: [58] Vendor Specific Information: Len=78 <?>
Capabilities: [e8] MSI: Enable- Count=1/1 Maskable- 64bit+
Capabilities: [d0] Express Endpoint, MSI 00
Capabilities: [100] Advanced Error Reporting
Capabilities: [13c] Virtual Channel
Capabilities: [160] Device Serial Number 7f-78-4e-ff-ff-6d-00-23
Capabilities: [16c] Power Budgeting <?>
Kernel driver in use: b43-pci-bridge
Kernel modules: ssb
===============================
Installation method ( http://wireless.kernel.org/en/users/Drivers/b43#fw-b43-lp
) :
You are using the b43 driver from linux-2.6.25 or newer
export FIRMWARE_INSTALL_DIR="/lib/firmware"
wget http://mirror2.openwrt.org/sources/broadcom-wl-4.150.10.5.tar.bz2
tar xjf broadcom-wl-4.150.10.5.tar.bz2
cd broadcom-wl-4.150.10.5/driver
sudo ../../b43-fwcutter-013/b43-fwcutter -w "$FIRMWARE_INSTALL_DIR"
wl_apsta_mimo.o
Seems work : ls /lib/firmware/b43-open/
a0g0bsinitvals5.fw a0g1bsinitvals9.fw b0g0bsinitvals9.fw
lp0bsinitvals15.fw n0initvals11.fw ucode5.fw
a0g0bsinitvals9.fw a0g1initvals13.fw b0g0initvals13.fw lp0initvals13.fw
pcm5.fw ucode9.fw
a0g0initvals5.fw a0g1initvals5.fw b0g0initvals5.fw lp0initvals14.fw
ucode11.fw
a0g0initvals9.fw a0g1initvals9.fw b0g0initvals9.fw lp0initvals15.fw
ucode13.fw
a0g1bsinitvals13.fw b0g0bsinitvals13.fw lp0bsinitvals13.fw
n0absinitvals11.fw ucode14.fw
a0g1bsinitvals5.fw b0g0bsinitvals5.fw lp0bsinitvals14.fw n0bsinitvals11.fw
ucode15.fw
But :
dmesg
b43-phy3 ERROR: You must go to
http://wireless.kernel.org/en/users/Drivers/b43#devicefirmware and download the
correct firmware for this driver version. Please carefully read all
instructions on this website.
b43-phy4: Broadcom 4312 WLAN found (core revision 15)
b43-phy4 debug: Found PHY: Analog 6, Type 5, Revision 1
b43-phy4 debug: Found Radio: Manuf 0x17F, Version 0x2062, Revision 2
phy4: Selected rate control algorithm 'minstrel'
Registered led device: b43-phy4::tx
Registered led device: b43-phy4::rx
Registered led device: b43-phy4::radio
Broadcom 43xx driver loaded [ Features: PMLS, Firmware-ID: FW13 ]
ssb0:0: Missing Free firmware
b43-phy4 ERROR: Rejected non-Free firmware
ssb0:0: Missing Free firmware
b43-phy4 ERROR: Rejected non-Free firmware
So don't work.
Grrrrrrrrrrrrrrrrrrrr
I thought nevertheless that with this kernel that was going to work.
No idea, I thing is due of the model [12e4:4315]. Is there anyone who can say
to me if it possible to install and configure this card with a free-kernel.
Thanx !
Cyrille
----
[ [email protected] | http://cbiot.fr ]
"Et le combat cessa faute de combattants."
--- Le Cid (1636), IV, 3, Rodrigue - - - -
BLAG : http://blagblagblag.org
Blag'em up! http://zenblagger.org
_______________________________________________
b43-dev mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/b43-dev
