Hello,
On 07/15/2016 01:19 PM, Wanderlei Huttel wrote:
> Hello Eric
>
> Thanks for response, but I was looking in src/jcr.h .code and I found
> this below, so I thought bacula should save the correct Level code.
>
> /* Backup/Verify level code. These are stored in the DB */
> #define L_FULL 'F' /* Full backup */
> #define L_INCREMENTAL 'I' /* since last backup */
> #define L_DIFFERENTIAL 'D' /* since last full backup */
> #define L_SINCE 'S'
> #define L_VERIFY_CATALOG 'C' /* verify from catalog */
> #define L_VERIFY_INIT 'V' /* verify save (init DB) */
> #define L_VERIFY_VOLUME_TO_CATALOG 'O' /* verify Volume to catalog
> entries */
> #define L_VERIFY_DISK_TO_CATALOG 'd' /* verify Disk attributes to
> catalog */
> #define L_VERIFY_DATA 'A' /* verify data on volume */
> #define L_BASE 'B' /* Base level job */
> #define L_NONE ' ' /* None, for Restore and Admin */
> #define L_VIRTUAL_FULL 'f' /* Virtual full backup */
>
> If I run a VirtualFull Is not possible to determine if it's a Full
> backup or VirtualFull backup just looking in the catalog?
This constant is used in the code, not in the catalog.
> Another question:
>
> In manual (pdf) says the following:
> In some respects the Vbackup feature works similar to a Migration job,
> in that Bacula normally reads the data from the pool specified in the
> Job resource, and writes it to the Next Pool specified in the Job
> resource. Note, this means that usually the output from the Virtual
> Backup is written into a different pool from where your prior backups
> are saved.
> Doing it this way guarantees that you will not get a deadlock situation
> attempting to read and write to the same volume in the Storage daemon.
>
>
> I've tryed to do a VirtualFull to the same Storage, but in bconsole I
> receive this status:
> 8 Back Virt 0 0 Backup_Maquina_Wanderlei is waiting
> on Storage "StorageLocal1"
Here, the message indicates that the Storage resource is probably not
configured properly.
> I have the option "Maximum Concurrent Jobs" in all resources that are
> necessary
I would advise to double check ;-)
> Pool{
> Name = "Daily"
> Pool Type = Backup
> Recycle = yes
> Recycle Oldest Volume = yes
> Purge Oldest Volume = yes
> Autoprune = yes
> LabelFormat = "Volume-Daily-${NumVolsDaily+:p/4/0/r}"
> Maximum Volume Bytes = 4Gb
> Maximum Volumes = 15
> NextPool = "VirtualFull"
> Storage = StorageLocal1
> }
>
> Pool{
> Name = "VirtualFull"
> Pool Type = Backup
> Recycle = yes
> Recycle Oldest Volume = yes
> Purge Oldest Volume = yes
> Autoprune = yes
> LabelFormat = "Volume-VirtualFull-${NumVolsVirtualFull+:p/4/0/r}"
> Maximum Volume Bytes = 4GB
> Maximum Volumes = 25
> Storage = StorageLocal1
> }
>
>
> Bacula does not allow VirtualFull to the same storage and different pool?
Yes, if your storage is properly configured. You need 2 devices at least
in your Storage Daemon.
Best Regards,
Eric
--
Need professional help and support for Bacula ?
Visit http://www.baculasystems.com
------------------------------------------------------------------------------
What NetFlow Analyzer can do for you? Monitors network bandwidth and traffic
patterns at an interface-level. Reveals which users, apps, and protocols are
consuming the most bandwidth. Provides multi-vendor support for NetFlow,
J-Flow, sFlow and other flows. Make informed decisions using capacity planning
reports.http://sdm.link/zohodev2dev
_______________________________________________
Bacula-users mailing list
Bacula-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/bacula-users
