On Thu, May 24, 2012 at 07:27:45PM +0600, Alexey Galakhov wrote:
> Signed-off-by: Alexey Galakhov <[email protected]>
> ---
> +
> +#define ADDR_V210_SDMMC_BASE 0xD0037488
> +#define ADDR_CopySDMMCtoMem 0xD0037F98
> +
> +#define RR(x) (*(volatile uint32_t*)(x))
> +
why not use regular readl/writel here?
> +int __bare_init s5p_irom_load_mmc(void *dest, uint32_t start_block, uint16_t
> block_count)
> +{
> + typedef uint32_t (*func_t) (int32_t, uint32_t, uint16_t, uint32_t*,
> int8_t);
> + uint32_t chbase = RR(ADDR_V210_SDMMC_BASE);
> + func_t func = (func_t)RR(ADDR_CopySDMMCtoMem);
> + int chan = (chbase - 0xEB000000) >> 20;
> + if (chan != 0 && chan != 2)
> + return 0;
> + return func(chan, start_block, block_count, (uint32_t*)dest, 0) ? 1 : 0;
> +}
> +
> +
> +void __bare_init board_init_lowlevel(void)
> +{
> + uint32_t r;
> +
> +#ifdef CONFIG_S3C_PLL_INIT
> + s5p_init_pll();
> +#endif
Can we do without pll init? If not, the ifdef should not be here.
> +
> + if (get_pc() < 0xD0000000) /* Are we running from iRAM? */
> + return; /* No, we don't. */
> +
> +#ifdef CONFIG_S3C_SDRAM_INIT
> + s5p_init_dram_bank_ddr2(S5P_DMC0_BASE, 0x20E00323, 0, 0);
> +#endif
Does it make sense to run this code without SDRAM setup code? It seems
the ifdef should not be here. Without SDRAM setup code you'll jump to
nirvana below.
> +
> + if (! s5p_irom_load_mmc((void*)TEXT_BASE - 16, 1, (barebox_image_size +
> 16 + 511) / 512))
> + while (1) { } /* hang */
> +
> + /* Jump to SDRAM */
> + r = (unsigned)TEXT_BASE;
> + __asm__ __volatile__("mov pc, %0" : : "r"(r));
> + while (1) { } /* hang */
> +}
> diff --git a/arch/arm/boards/tiny210/tiny210.c
> b/arch/arm/boards/tiny210/tiny210.c
> +static int tiny210_mem_init(void)
> +{
> + arm_add_mem_device("ram0", S3C_SDRAM_BASE, s5p_get_memory_size());
> + return 0;
> +}
> +mem_initcall(tiny210_mem_init);
> +
> +static int tiny210_console_init(void)
> +{
> + /*
> + * configure the UART1 right now, as barebox will
> + * start to send data immediately
> + */
> + s3c_gpio_mode(GPA00_RXD0 | ENABLE_PU);
> + s3c_gpio_mode(GPA01_TXD0);
> + s3c_gpio_mode(GPA02_NCTS0 | ENABLE_PU);
> + s3c_gpio_mode(GPA03_NRTS0);
> +
> + add_generic_device("s3c_serial", -1, NULL,
Please use DEVICE_ID_DYNAMIC instead of -1.
Sascha
--
Pengutronix e.K. | |
Industrial Linux Solutions | http://www.pengutronix.de/ |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox
