Am Donnerstag, den 23.08.2018, 18:57 -0700 schrieb Andrey Smirnov:
> On Thu, Aug 23, 2018 at 2:59 AM Florian Bäuerle
> <[email protected]> wrote:
> >
> > Signed-off-by: Florian Bäuerle <[email protected]>
> > ---
> > arch/arm/boards/phytec-phycard-imx27/lowlevel.c | 15 +++++++++++++++
> > arch/arm/mach-imx/include/mach/debug_ll.h | 13 +++++++++++++
> > include/serial/imx-uart.h | 5 +++++
> > 3 files changed, 33 insertions(+)
> >
> > diff --git a/arch/arm/boards/phytec-phycard-imx27/lowlevel.c
> > b/arch/arm/boards/phytec-phycard-imx27/lowlevel.c
> > index e1132e0..8244337 100644
> > --- a/arch/arm/boards/phytec-phycard-imx27/lowlevel.c
> > +++ b/arch/arm/boards/phytec-phycard-imx27/lowlevel.c
> > @@ -14,6 +14,8 @@
> > #include <mach/imx-pll.h>
> > #include <mach/esdctl.h>
> > #include <mach/imx-nand.h>
> > +#include <mach/debug_ll.h>
> > +#include <serial/imx-uart.h>
> >
> > #define ESDCTL0_VAL (ESDCTL0_SDE | ESDCTL0_ROW13 | ESDCTL0_COL10)
> >
> > @@ -58,6 +60,18 @@ static void sdram_init(void)
> > MX27_ESDCTL_BASE_ADDR + IMX_ESDCTL0);
> > }
> >
> > +static void setup_uart(void)
> > +{
> > + /* Set PE[12-15] use, direction, function and pull-up */
> > + writel(0xfffc0f27, MX27_GPIO5_BASE_ADDR + 0x20);
> > + writel(0x00005000, MX27_GPIO5_BASE_ADDR);
> > + writel(0x00000000, MX27_GPIO5_BASE_ADDR + 0x38);
> > + writel(0xffff0fff, MX27_GPIO5_BASE_ADDR + 0x40);
> > +
>
> Can constants from iomux-imx27.h be used here?
In theory yes, it could be done with imx_gpio_mode(). I think it's better to
leave it as is, otherwise, we'd need a) the pinctrl driver in
the pbl (probably
too large) or b) do the same as imx_gpio_mode and extract the ORed values from a
newly defined constant and basically
reimplement imx_gpio_mode.
The register offsets are also only defined in drivers/pinctrl/imx-iomux-v1.c
>
> > + imx27_ungate_all_peripherals();
> > + imx27_uart_setup_ll();
> > +}
> > +
> > void __bare_init __naked phytec_phycard_imx27_common_init(void *fdt)
> > {
> > unsigned long r;
> > @@ -97,6 +111,7 @@ void __bare_init __naked
> > phytec_phycard_imx27_common_init(void *fdt)
> > MX27_CSCR_MSHC_SEL, MX27_CCM_BASE_ADDR + MX27_CSCR);
> >
> > sdram_init();
> > + setup_uart();
>
> Majority of the boards gates this to happen on if
> IS_ENABLED(CONFIG_DEBUG_LL) is true, so it might make sense to do the
> same.
you're right.
>
> >
> > imx27_barebox_boot_nand_external(fdt);
> > }
> > diff --git a/arch/arm/mach-imx/include/mach/debug_ll.h
> > b/arch/arm/mach-imx/include/mach/debug_ll.h
> > index 1550e05..6c9b21d 100644
> > --- a/arch/arm/mach-imx/include/mach/debug_ll.h
> > +++ b/arch/arm/mach-imx/include/mach/debug_ll.h
> > @@ -56,6 +56,12 @@
> > #error "unknown i.MX debug uart soc type"
> > #endif
> >
> > +static inline void imx27_uart_setup_ll(void) {
> > + void *base = IOMEM(IMX_UART_BASE(IMX_DEBUG_SOC,
> > + CONFIG_DEBUG_IMX_UART_PORT));
> > + imx27_uart_setup(base);
> > +}
> > +
> > static inline void imx50_uart_setup_ll(void)
> > {
> > void *base = IOMEM(IMX_UART_BASE(IMX_DEBUG_SOC,
> > CONFIG_DEBUG_IMX_UART_PORT));
> > @@ -121,6 +127,7 @@ static inline void PUTC_LL(int c)
> >
> > #else
> >
> > +static inline void imx27_uart_setup_ll(void) {}
> > static inline void imx50_uart_setup_ll(void) {}
> > static inline void imx51_uart_setup_ll(void) {}
> > static inline void imx53_uart_setup_ll(void) {}
> > @@ -138,6 +145,12 @@ static inline void imx_ungate_all_peripherals(void
> > __iomem *ccmbase)
> > writel(0xffffffff, ccmbase + i);
> > }
> >
> > +static inline void imx27_ungate_all_peripherals(void)
> > +{
> > + writel(0xfffffbff, IOMEM(MX27_CCM_BASE_ADDR) + 0x20);
> > + writel(0xfffffffc, IOMEM(MX27_CCM_BASE_ADDR) + 0x24);
> > +}
>
> I think you can use MX27_PCCR0 and MX27_PCCR1 here instead of magic numbers.
yep, thanks.
>
> > +
> > static inline void imx6_ungate_all_peripherals(void)
> > {
> > imx_ungate_all_peripherals(IOMEM(MX6_CCM_BASE_ADDR));
> > diff --git a/include/serial/imx-uart.h b/include/serial/imx-uart.h
> > index c236065..0c033c2 100644
> > --- a/include/serial/imx-uart.h
> > +++ b/include/serial/imx-uart.h
> > @@ -155,6 +155,11 @@ static inline void imx_uart_set_dte(void __iomem
> > *uartbase)
> > writel(ufcr, uartbase + UFCR);
> > }
> >
> > +static inline void imx27_uart_setup(void __iomem *uartbase)
> > +{
> > + imx_uart_setup(uartbase, 66500000);
> > +}
> > +
> > static inline void imx50_uart_setup(void __iomem *uartbase)
> > {
> > imx_uart_setup(uartbase, 66666666);
> > --
> > 1.8.3.1
> >
> >
> > _______________________________________________
> > barebox mailing list
> > [email protected]
> > http://lists.infradead.org/mailman/listinfo/barebox
_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox
