In Linux, '---help---' was deprecated in favor of 'help', and this is checked by the recent checkpatch.pl
See Linux commit 84af7a6194e493fae312a2b7fa5a3b51f76d9282 The number of '---help---' is gradually decreasing in Linux, but there are still lots. However, '---help---' will be completely killed when the time comes. Fortunately, there are only some in Barebox. Replacing them is not hard. Signed-off-by: Masahiro Yamada <[email protected]> --- arch/mips/Kconfig | 2 +- drivers/mtd/devices/Kconfig | 2 +- drivers/net/Kconfig | 4 ++-- drivers/net/phy/Kconfig | 26 +++++++++++++------------- drivers/nvme/host/Kconfig | 2 +- drivers/w1/Kconfig | 4 ++-- 6 files changed, 20 insertions(+), 20 deletions(-) diff --git a/arch/mips/Kconfig b/arch/mips/Kconfig index 5901930a7..936e56fa2 100644 --- a/arch/mips/Kconfig +++ b/arch/mips/Kconfig @@ -35,7 +35,7 @@ config MIPS_RELOCATION_TABLE_SIZE hex "Relocation table size" range 0x100 0x10000 default "0x8000" - ---help--- + help A table of relocation data will be appended to the Barebox binary and parsed in relocate_code() to fix up all offsets in the relocated Barebox. diff --git a/drivers/mtd/devices/Kconfig b/drivers/mtd/devices/Kconfig index 25db10a9b..47296cf51 100644 --- a/drivers/mtd/devices/Kconfig +++ b/drivers/mtd/devices/Kconfig @@ -52,7 +52,7 @@ config MTD_DOCG3 bool "M-Systems Disk-On-Chip G3" select BCH select BITREV - ---help--- + help This provides an MTD device driver for the M-Systems DiskOnChip G3 devices. diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig index 3e3de5a97..beeb4b822 100644 --- a/drivers/net/Kconfig +++ b/drivers/net/Kconfig @@ -108,13 +108,13 @@ config DRIVER_NET_ENC28J60 bool "ENC28J60 support" depends on SPI select PHYLIB - ---help--- + help Support for the Microchip EN28J60 ethernet chip. config DRIVER_NET_ENC28J60_WRITEVERIFY bool "Enable write verify" depends on DRIVER_NET_ENC28J60 - ---help--- + help Enable the verify after the buffer write useful for debugging purpose. If unsure, say N. diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig index c08b8257a..2806af376 100644 --- a/drivers/net/phy/Kconfig +++ b/drivers/net/phy/Kconfig @@ -10,52 +10,52 @@ comment "MII PHY device drivers" config AR8327N_PHY bool "Driver for QCA AR8327N PHYs" - ---help--- + help Currently supports the AR8327N PHY. config AT803X_PHY bool "Driver for Atheros AT803X PHYs" - ---help--- + help Currently supports the AT8030, AT8031 and AT8035 PHYs. config DAVICOM_PHY bool "Driver for Davicom PHYs" - ---help--- + help Currently supports dm9161e and dm9131 config DP83867_PHY tristate "Texas Instruments DP83867 Gigabit PHY" - ---help--- + help Currently supports the DP83867 PHY. config LXT_PHY bool "Driver for the Intel LXT PHYs" - ---help--- + help Currently supports the lxt971 PHY. config MARVELL_PHY tristate "Drivers for Marvell PHYs" - ---help--- + help Add support for various Marvell PHYs (e.g. 88E1121R). config MICREL_PHY bool "Driver for Micrel PHYs" - ---help--- + help Supports the KSZ9021, VSC8201, KS8001 PHYs. config NATIONAL_PHY bool "Driver for National Semiconductor PHYs" - ---help--- + help Currently supports the DP83865 PHY. config REALTEK_PHY bool "Driver for Realtek PHYs" - ---help--- + help Supports the Realtek 821x PHY. config SMSC_PHY bool "Drivers for SMSC PHYs" - ---help--- + help Currently supports the LAN83C185, LAN8187 and LAN8700 PHYs config NET_DSA_MV88E6XXX @@ -69,12 +69,12 @@ comment "MII bus device drivers" config MDIO_MVEBU bool "Driver for MVEBU SoC MDIO bus" depends on ARCH_MVEBU - ---help--- + help Driver for the MDIO bus found on Marvell EBU SoCs. config MDIO_BITBANG bool "Support for bitbanged MDIO buses" - ---help--- + help This module implements the MDIO bus protocol in software, for use by low level drivers that export the ability to drive the relevant pins. @@ -84,7 +84,7 @@ config MDIO_BITBANG config MDIO_GPIO bool "Support for GPIO lib-based bitbanged MDIO buses" depends on MDIO_BITBANG && GPIOLIB - ---help--- + help Supports GPIO lib-based MDIO busses. config MDIO_BUS_MUX diff --git a/drivers/nvme/host/Kconfig b/drivers/nvme/host/Kconfig index 8888c8900..5499f97d7 100644 --- a/drivers/nvme/host/Kconfig +++ b/drivers/nvme/host/Kconfig @@ -5,7 +5,7 @@ config BLK_DEV_NVME bool "NVM Express block device" depends on PCI && BLOCK select NVME_CORE - ---help--- + help The NVM Express driver is for solid state drives directly connected to the PCI or PCI Express bus. If you know you don't have one of these, it is safe to answer N. diff --git a/drivers/w1/Kconfig b/drivers/w1/Kconfig index 4a16197c6..6299f6e16 100644 --- a/drivers/w1/Kconfig +++ b/drivers/w1/Kconfig @@ -1,6 +1,6 @@ menuconfig W1 bool "Dallas's 1-wire support" - ---help--- + help Dallas' 1-wire bus is useful to connect slow 1-pin devices such as iButtons and thermal sensors. @@ -13,7 +13,7 @@ source "drivers/w1/slaves/Kconfig" config W1_DUAL_SEARCH bool "dual search" - ---help--- + help Some device need to be searched twice to be detected endif # W1 -- 2.17.1 _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
