On Mon, May 27, 2019 at 12:00:58PM +0200, Michael Grzeschik wrote: > Signed-off-by: Michael Grzeschik <[email protected]> > --- > v1 -> v2: > > - removed unnecessary chapter in kconfig helptext > - removed platform data setup and teardown callbacks > - removed error path for xzalloc > > drivers/gpio/Kconfig | 16 ++ > drivers/gpio/Makefile | 1 + > drivers/gpio/gpio-pcf857x.c | 261 ++++++++++++++++++++++++++++++++ > include/platform_data/pcf857x.h | 41 +++++ > 4 files changed, 319 insertions(+) > create mode 100644 drivers/gpio/gpio-pcf857x.c > create mode 100644 include/platform_data/pcf857x.h > > diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig > index c535904ed0..9bfa97160c 100644 > --- a/drivers/gpio/Kconfig > +++ b/drivers/gpio/Kconfig > @@ -98,6 +98,22 @@ config GPIO_PCA953X > > 40 bits: pca9505, pca9698 > > +config GPIO_PCF857X > + tristate "PCF857x, PCA{85,96}7x, and MAX732[89] I2C GPIO expanders" > + depends on I2C > + help > + Say yes here to provide access to most "quasi-bidirectional" I2C > + GPIO expanders used for additional digital outputs or inputs. > + Most of these parts are from NXP, though TI is a second source for > + some of them. Compatible models include: > + > + 8 bits: pcf8574, pcf8574a, pca8574, pca8574a, > + pca9670, pca9672, pca9674, pca9674a, > + max7328, max7329 > + > + 16 bits: pcf8575, pcf8575c, pca8575, > + pca9671, pca9673, pca9675 > + > config GPIO_PL061 > bool "PrimeCell PL061 GPIO support" > depends on ARM_AMBA > diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile > index 52280f0bb4..990df01788 100644 > --- a/drivers/gpio/Makefile > +++ b/drivers/gpio/Makefile > @@ -14,6 +14,7 @@ obj-$(CONFIG_GPIO_MALTA_FPGA_I2C) += gpio-malta-fpga-i2c.o > obj-$(CONFIG_GPIO_ORION) += gpio-orion.o > obj-$(CONFIG_GPIO_OMAP) += gpio-omap.o > obj-$(CONFIG_GPIO_PCA953X) += gpio-pca953x.o > +obj-$(CONFIG_GPIO_PCF857X) += gpio-pcf857x.o > obj-$(CONFIG_GPIO_PL061) += gpio-pl061.o > obj-$(CONFIG_GPIO_STMPE) += gpio-stmpe.o > obj-$(CONFIG_GPIO_TEGRA) += gpio-tegra.o > diff --git a/drivers/gpio/gpio-pcf857x.c b/drivers/gpio/gpio-pcf857x.c > new file mode 100644 > index 0000000000..f857a24f8a > --- /dev/null > +++ b/drivers/gpio/gpio-pcf857x.c > @@ -0,0 +1,261 @@ > +/* > + * Driver for pcf857x, pca857x, and pca967x I2C GPIO expanders > + * > + * This code was ported from linux-5.1 kernel by Michael Grzeschik. > + * > + * Copyright (C) 2007 David Brownell > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License as published by > + * the Free Software Foundation; either version 2 of the License, or > + * (at your option) any later version. > + */ > + > +#include <common.h> > +#include <malloc.h> > +#include <driver.h> > +#include <xfuncs.h> > +#include <errno.h> > +#include <i2c/i2c.h> > + > +#include <gpio.h> > +#include <platform_data/pcf857x.h> > + > +static const struct platform_device_id pcf857x_id[] = { > + { "pcf8574", 8 }, > + { "pcf8574a", 8 }, > + { "pca8574", 8 }, > + { "pca9670", 8 }, > + { "pca9672", 8 }, > + { "pca9674", 8 }, > + { "pcf8575", 16 }, > + { "pca8575", 16 }, > + { "pca9671", 16 }, > + { "pca9673", 16 }, > + { "pca9675", 16 }, > + { "max7328", 8 }, > + { "max7329", 8 }, > + { } > +}; > + > +/* > + * The pcf857x, pca857x, and pca967x chips only expose one read and one > + * write register. Writing a "one" bit (to match the reset state) lets > + * that pin be used as an input; it's not an open-drain model, but acts > + * a bit like one. This is described as "quasi-bidirectional"; read the > + * chip documentation for details. > + * > + * Many other I2C GPIO expander chips (like the pca953x models) have > + * more complex register models and more conventional circuitry using > + * push/pull drivers. They often use the same 0x20..0x27 addresses as > + * pcf857x parts, making the "legacy" I2C driver model problematic. > + */ > +struct pcf857x { > + struct gpio_chip chip; > + struct i2c_client *client; > + unsigned out; /* software latch */ > + > + int (*write)(struct i2c_client *client, unsigned data); > + int (*read)(struct i2c_client *client); > +}; > + > +static inline struct pcf857x *to_pcf(struct gpio_chip *gc) > +{ > + return container_of(gc, struct pcf857x, chip); > +} > + > +/*-------------------------------------------------------------------------*/ > + > +/* Talk to 8-bit I/O expander */ > + > +static int i2c_write_le8(struct i2c_client *client, unsigned data) > +{ > + return i2c_smbus_write_byte(client, data); > +} > + > +static int i2c_read_le8(struct i2c_client *client) > +{ > + return (int)i2c_smbus_read_byte(client); > +} > + > +/* Talk to 16-bit I/O expander */ > + > +static int i2c_write_le16(struct i2c_client *client, unsigned word) > +{ > + u8 buf[2] = { word & 0xff, word >> 8, }; > + int ret; > + > + ret = i2c_master_send(client, buf, 2); > + return (ret < 0) ? ret : 0; > +} > + > +static int i2c_read_le16(struct i2c_client *client) > +{ > + u8 buf[2]; > + int ret; > + > + ret = i2c_master_recv(client, buf, 2); > + if (ret < 0) > + return ret; > + return (buf[1] << 8) | buf[0]; > +} > + > +/*-------------------------------------------------------------------------*/ > + > +static int pcf857x_input(struct gpio_chip *chip, unsigned offset) > +{ > + struct pcf857x *gpio = to_pcf(chip); > + int ret; > + > + gpio->out |= (1 << offset); > + ret = gpio->write(gpio->client, gpio->out); > + > + return ret; > +} > + > +static int pcf857x_get(struct gpio_chip *chip, unsigned offset) > +{ > + struct pcf857x *gpio = to_pcf(chip); > + int value; > + > + value = gpio->read(gpio->client); > + return (value < 0) ? value : !!(value & (1 << offset)); > +} > + > +static int pcf857x_output(struct gpio_chip *chip, unsigned offset, int value) > +{ > + struct pcf857x *gpio = to_pcf(chip); > + unsigned bit = 1 << offset; > + int ret; > + > + if (value) > + gpio->out |= bit; > + else > + gpio->out &= ~bit; > + ret = gpio->write(gpio->client, gpio->out); > + > + return ret; > +} > + > +static void pcf857x_set(struct gpio_chip *chip, unsigned offset, int value) > +{ > + pcf857x_output(chip, offset, value); > +} > + > +/*-------------------------------------------------------------------------*/ > + > +static struct gpio_ops pcf857x_gpio_ops = { > + .direction_input = pcf857x_input, > + .direction_output = pcf857x_output, > + .get = pcf857x_get, > + .set = pcf857x_set, > +}; > + > +static int pcf857x_probe(struct device_d *dev) > +{ > + struct i2c_client *client = to_i2c_client(dev); > + struct pcf857x_platform_data *pdata = dev->platform_data; > + struct device_node *np = dev->device_node; > + struct pcf857x *gpio; > + unsigned long driver_data; > + unsigned int n_latch = 0; > + int ret; > + > + if (IS_ENABLED(CONFIG_OF) && np) > + of_property_read_u32(np, "lines-initial-states", &n_latch); > + else if (pdata) > + n_latch = pdata->n_latch; > + > + /* Allocate, initialize, and register this gpio_chip. */ > + gpio = xzalloc(sizeof(*gpio)); > + > + ret = dev_get_drvdata(dev, (const void **)&driver_data); > + if (ret) > + return ret; > + > + gpio->chip.base = pdata ? pdata->gpio_base : -1; > + gpio->chip.ops = &pcf857x_gpio_ops; > + gpio->chip.ngpio = driver_data; > + gpio->chip.dev = &client->dev; > + > + /* NOTE: the OnSemi jlc1562b is also largely compatible with > + * these parts, notably for output. It has a low-resolution > + * DAC instead of pin change IRQs; and its inputs can be the > + * result of comparators. > + */ > + > + /* 8574 addresses are 0x20..0x27; 8574a uses 0x38..0x3f; > + * 9670, 9672, 9764, and 9764a use quite a variety. > + * > + * NOTE: we don't distinguish here between *4 and *4a parts. > + */ > + switch (gpio->chip.ngpio) { > + case 8: > + gpio->write = i2c_write_le8; > + gpio->read = i2c_read_le8; > + break; > + /* '75/'75c addresses are 0x20..0x27, just like the '74; > + * the '75c doesn't have a current source pulling high. > + * 9671, 9673, and 9765 use quite a variety of addresses. > + * > + * NOTE: we don't distinguish here between '75 and '75c parts. > + */ > + case 16: > + gpio->write = i2c_write_le16; > + gpio->read = i2c_read_le16; > + break; > + default: > + dev_warn(&client->dev, "unsupported number of gpios\n"); > + return -EINVAL; > + } > + > + gpio->client = client; > + > + /* NOTE: these chips have strange "quasi-bidirectional" I/O pins. > + * We can't actually know whether a pin is configured (a) as output > + * and driving the signal low, or (b) as input and reporting a low > + * value ... without knowing the last value written since the chip > + * came out of reset (if any). We can't read the latched output. > + * > + * In short, the only reliable solution for setting up pin direction > + * is to do it explicitly. The setup() method can do that, but it > + * may cause transient glitching since it can't know the last value > + * written (some pins may need to be driven low). > + *
Damn, I missed the comment refering to the setup function.
> + * Using n_latch avoids that trouble. When left initialized to zero,
> + * our software copy of the "latch" then matches the chip's all-ones
> + * reset state. Otherwise it flags pins to be driven low.
> + */
> + gpio->out = ~n_latch;
> +
> + ret = gpiochip_add(&gpio->chip);
> + if (ret)
> + return ret;
> +
> + return ret;
> +}
> +
> +static const struct of_device_id pcf857x_dt_ids[] = {
> + { .compatible = "nxp,pcf8574", .data = (void *)8 },
> + { .compatible = "nxp,pcf8574a", .data = (void *)8 },
> + { .compatible = "nxp,pca8574", .data = (void *)8 },
> + { .compatible = "nxp,pca9670", .data = (void *)8 },
> + { .compatible = "nxp,pca9672", .data = (void *)8 },
> + { .compatible = "nxp,pca9674", .data = (void *)8 },
> + { .compatible = "nxp,pcf8575", .data = (void *)16 },
> + { .compatible = "nxp,pca8575", .data = (void *)16 },
> + { .compatible = "nxp,pca9671", .data = (void *)16 },
> + { .compatible = "nxp,pca9673", .data = (void *)16 },
> + { .compatible = "nxp,pca9675", .data = (void *)16 },
> + { .compatible = "maxim,max7328", .data = (void *)8 },
> + { .compatible = "maxim,max7329", .data = (void *)8 },
> + { }
> +};
> +
> +static struct driver_d pcf857x_driver = {
> + .name = "pcf857x",
> + .probe = pcf857x_probe,
> + .of_compatible = DRV_OF_COMPAT(pcf857x_dt_ids),
> + .id_table = pcf857x_id,
> +};
> +device_i2c_driver(pcf857x_driver);
> diff --git a/include/platform_data/pcf857x.h b/include/platform_data/pcf857x.h
> new file mode 100644
> index 0000000000..2ea2b7dd52
> --- /dev/null
> +++ b/include/platform_data/pcf857x.h
> @@ -0,0 +1,41 @@
> +/* SPDX-License-Identifier: GPL-2.0 */
> +#ifndef __LINUX_PCF857X_H
> +#define __LINUX_PCF857X_H
> +
> +#include <linux/types.h>
> +#include <i2c/i2c.h>
> +
> +/**
> + * struct pcf857x_platform_data - data to set up pcf857x driver
> + * @gpio_base: number of the chip's first GPIO
> + * @n_latch: optional bit-inverse of initial register value; if
> + * you leave this initialized to zero the driver will act
> + * like the chip was just reset
> + * @setup: optional callback issued once the GPIOs are valid
> + * @teardown: optional callback issued before the GPIOs are invalidated
> + * @context: optional parameter passed to setup() and teardown()
> + *
Here also to the teardown function. The conext can be removed as well.
> + * In addition to the I2C_BOARD_INFO() state appropriate to each chip,
> + * the i2c_board_info used with the pcf875x driver must provide its
> + * platform_data (pointer to one of these structures) with at least
> + * the gpio_base value initialized.
> + *
> + * The @setup callback may be used with the kind of board-specific glue
> + * which hands the (now-valid) GPIOs to other drivers, or which puts
> + * devices in their initial states using these GPIOs.
> + *
> + * These GPIO chips are only "quasi-bidirectional"; read the chip specs
> + * to understand the behavior. They don't have separate registers to
> + * record which pins are used for input or output, record which output
> + * values are driven, or provide access to input values. That must be
> + * inferred by reading the chip's value and knowing the last value written
> + * to it. If you leave n_latch initialized to zero, that last written
> + * value is presumed to be all ones (as if the chip were just reset).
> + */
> +struct pcf857x_platform_data {
> + unsigned gpio_base;
> + unsigned n_latch;
> + void *context;
> +};
> +
> +#endif /* __LINUX_PCF857X_H */
Basically, the whole file can be removed.
I will send v3.
> --
> 2.20.1
>
>
> _______________________________________________
> barebox mailing list
> [email protected]
> http://lists.infradead.org/mailman/listinfo/barebox
>
--
Pengutronix e.K. | |
Industrial Linux Solutions | http://www.pengutronix.de/ |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
signature.asc
Description: PGP signature
_______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
