Add basic support for the MyirTech MYD-YA15XC-T development board [1]. ... deep-probe: supported due to myir,myc-stm32mp15x stm32mp-init: detected STM32MP151AAC Rev.Z STM32 RCC reset reason POR (MP_RSTSR: 0x00000015) Boot from SD... psci psci.of: detected version 1.1 stpmic1-i2c stpmic10: PMIC Chip Version: 0x21 stm32-usbphyc [email protected]: registered rev:1.0 nand_base: device found, Manufacturer ID: 0x2c, Chip ID: 0xda nand_base: Micron MT29F2G08ABAEAWP nand_base: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 Bad block table found at page 131008, version 0x01 Bad block table found at page 130944, version 0x01 nand_read_bbt: bad block at 0x000000d60000 nand_read_bbt: bad block at 0x000000fa0000 nand_read_bbt: bad block at 0x00000d460000 stm32_sdmmc [email protected]: registered as mmc0 mmc0: detected SD card version 2.0 mmc0: registered mmc0 stm32_sdmmc [email protected]: registered as mmc1 stm32-iwdg [email protected]: probed Product name: MYC-YA151C-256N256D-65-I-T Product serial: TW202103290400145 malloc space: 0xc7ef7a80 -> 0xcfdef4ff (size 127 MiB) envfs: no envfs (magic mismatch) - envfs never written? NOTICE: ubi0: scanning is finished NOTICE: ubi0: registering /dev/nand0.system.ubi NOTICE: ubi0: registering kernel as /dev/nand0.system.ubi.kernel NOTICE: ubi0: registering root as /dev/nand0.system.ubi.root NOTICE: ubi0: registering bbox as /dev/nand0.system.ubi.bbox NOTICE: ubi0: attached mtd0 (name "nand0.system", size 237 MiB) to ubi0 NOTICE: ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes NOTICE: ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 NOTICE: ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 NOTICE: ubi0: good PEBs: 1895, bad PEBs: 5, corrupted PEBs: 0 NOTICE: ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128 NOTICE: ubi0: max/mean erase counter: 1/0, WL threshold: 65536, image sequence number: 3389077539 NOTICE: ubi0: available PEBs: 529, total reserved PEBs: 1366, PEBs reserved for bad PEB handling: 35
Hit m for menu or any to stop autoboot: 2 barebox@MYC-YA151C-256N256D-65-I-T:/ ... [1] https://www.myirtech.com/list.asp?id=659 Signed-off-by: Alexander Shiyan <[email protected]> --- arch/arm/boards/Makefile | 1 + arch/arm/boards/myirtech-stm32/Makefile | 4 + arch/arm/boards/myirtech-stm32/board.c | 143 +++++++ arch/arm/boards/myirtech-stm32/lowlevel.c | 27 ++ arch/arm/dts/Makefile | 1 + arch/arm/dts/stm32mp15x-myirtech-myc.dtsi | 351 +++++++++++++++++ arch/arm/dts/stm32mp15x-myirtech-myd.dts | 458 ++++++++++++++++++++++ arch/arm/mach-stm32mp/Kconfig | 7 + images/Makefile.stm32mp | 2 + 9 files changed, 994 insertions(+) create mode 100644 arch/arm/boards/myirtech-stm32/Makefile create mode 100644 arch/arm/boards/myirtech-stm32/board.c create mode 100644 arch/arm/boards/myirtech-stm32/lowlevel.c create mode 100644 arch/arm/dts/stm32mp15x-myirtech-myc.dtsi create mode 100644 arch/arm/dts/stm32mp15x-myirtech-myd.dts diff --git a/arch/arm/boards/Makefile b/arch/arm/boards/Makefile index 83a3179185..2ff10329b2 100644 --- a/arch/arm/boards/Makefile +++ b/arch/arm/boards/Makefile @@ -140,6 +140,7 @@ obj-$(CONFIG_MACH_SOLIDRUN_MICROSOM) += solidrun-microsom/ obj-$(CONFIG_MACH_STM32MP15XX_DKX) += stm32mp15xx-dkx/ obj-$(CONFIG_MACH_STM32MP13XX_DK) += stm32mp13xx-dk/ obj-$(CONFIG_MACH_LXA_MC1) += lxa-mc1/ +obj-$(CONFIG_MACH_MYIRTECH_STM32MP1) += myirtech-stm32/ obj-$(CONFIG_MACH_STM32MP15X_EV1) += stm32mp15x-ev1/ obj-$(CONFIG_MACH_TECHNEXION_PICO_HOBBIT) += technexion-pico-hobbit/ obj-$(CONFIG_MACH_TECHNEXION_WANDBOARD) += technexion-wandboard/ diff --git a/arch/arm/boards/myirtech-stm32/Makefile b/arch/arm/boards/myirtech-stm32/Makefile new file mode 100644 index 0000000000..511d4971fa --- /dev/null +++ b/arch/arm/boards/myirtech-stm32/Makefile @@ -0,0 +1,4 @@ +# SPDX-License-Identifier: GPL-2.0-only + +lwl-y += lowlevel.o +obj-y += board.o diff --git a/arch/arm/boards/myirtech-stm32/board.c b/arch/arm/boards/myirtech-stm32/board.c new file mode 100644 index 0000000000..187a3b8a59 --- /dev/null +++ b/arch/arm/boards/myirtech-stm32/board.c @@ -0,0 +1,143 @@ +// SPDX-License-Identifier: GPL-2.0+ + +#include <bootsource.h> +#include <common.h> +#include <deep-probe.h> +#include <envfs.h> +#include <environment.h> +#include <globalvar.h> +#include <init.h> +#include <machine_id.h> +#include <net.h> +#include <of.h> +#include <mach/stm32mp/bbu.h> + +struct id_eeprom { + u8 hrcw_primary[0x10]; + u8 pn[64]; + u8 sn[64]; + u8 mac0[6]; + u8 mac1[6]; +} __packed; + +static int stm32mp15x_myirtech_serial_fixup(struct device_node *root, void *unused) +{ + char *serial; + + serial = basprintf("%s", getenv("global.machine_id")); + of_set_property(root, "serial-number", serial, strlen(serial) + 1, 1); + free(serial); + + return 0; +} + +static int stm32mp15x_myirtech_eeprom_init(void) +{ + struct id_eeprom eeprom; + struct cdev *cdev; + char str[64]; + int len; + + if (!of_machine_is_compatible("myir,myc-stm32mp15x")) + return 0; + + cdev = cdev_by_name("eeprom0"); + if (!cdev) { + pr_err("Can't find EEPROM\n"); + return -ENODEV; + } + + if (cdev_read(cdev, &eeprom, sizeof(eeprom), 0, 0) < 0) { + pr_err("Can't read EEPROM\n"); + return -EIO; + } + + len = (eeprom.pn[0] - '0'); + if ((len < 8) || (len > 64)) { + pr_err("Unable to get product name\n"); + return -EINVAL; + } + + strncpy(str, &eeprom.pn[1], len); + str[len] = '\0'; + pr_info("Product name: %s\n", str); + globalvar_add_simple("model", str); + + len = (eeprom.sn[0] - '0'); + if ((len < 8) || (len > 64)) { + pr_err("Unable to get product serial\n"); + return -EINVAL; + } + + strncpy(str, &eeprom.sn[1], len); + str[len] = '\0'; + pr_info("Product serial: %s\n", str); + machine_id_set_hashable(str, len); + of_register_fixup(stm32mp15x_myirtech_serial_fixup, NULL); + + if (!is_valid_ether_addr(eeprom.mac0)) { + int i, j; + + /* Make fixed MAC-address based on serial number */ + memcpy(eeprom.mac0, str, sizeof(eeprom.mac0)); + for (i = sizeof(eeprom.mac0); i < len; i++) + for (j = 0; j < sizeof(eeprom.mac0); j++) + eeprom.mac0[j] ^= str[i]; + } + + eth_register_ethaddr(0, eeprom.mac0); + + return 0; +} +of_populate_initcall(stm32mp15x_myirtech_eeprom_init); + +static int stm32mp15x_myirtech_probe(struct device *dev) +{ + int instance = bootsource_get_instance(), def = -1; + const enum bootsource bs = bootsource_get(); + + barebox_set_hostname("myir-stm32"); + + switch (bs) { + case BOOTSOURCE_MMC: + if (instance == 0) { + of_device_enable_path("/chosen/environment-sd"); + pr_info("Boot from SD...\n"); + } else { + of_device_enable_path("/chosen/environment-emmc"); + pr_info("Boot from eMMC...\n"); + } + def = instance; + break; + case BOOTSOURCE_NAND: + of_device_enable_path("/chosen/environment-nand"); + pr_info("Boot from NAND...\n"); + def = 2; + break; + default: + return 0; + } + + stm32mp_bbu_mmc_register_handler("sd", "/dev/mmc0.ssbl", + (def == 0) ? BBU_HANDLER_FLAG_DEFAULT : 0); + + stm32mp_bbu_mmc_register_handler("emmc", "/dev/mmc1.ssbl", + (def == 1) ? BBU_HANDLER_FLAG_DEFAULT : 0); + + //TODO: NAND + + return 0; +} + +static const struct of_device_id stm32mp15x_myirtech_of_match[] = { + { .compatible = "myir,myc-stm32mp15x" }, + { }, +}; +BAREBOX_DEEP_PROBE_ENABLE(stm32mp15x_myirtech_of_match); + +static struct driver stm32mp15x_myirtech_board_driver = { + .name = "board-myirtech-stm32", + .probe = stm32mp15x_myirtech_probe, + .of_compatible = stm32mp15x_myirtech_of_match, +}; +device_platform_driver(stm32mp15x_myirtech_board_driver); diff --git a/arch/arm/boards/myirtech-stm32/lowlevel.c b/arch/arm/boards/myirtech-stm32/lowlevel.c new file mode 100644 index 0000000000..715a8eeb96 --- /dev/null +++ b/arch/arm/boards/myirtech-stm32/lowlevel.c @@ -0,0 +1,27 @@ +// SPDX-License-Identifier: GPL-2.0+ + +#include <common.h> +#include <mach/stm32mp/entry.h> +#include <debug_ll.h> + +extern char __dtb_z_stm32mp15x_myirtech_myd_start[]; + +static void setup_uart(void) +{ + /* first stage has set up the UART, so nothing to do here */ + putc_ll('>'); +} + +ENTRY_FUNCTION(start_stm32mp15x_myir, r0, r1, r2) +{ + void *fdt; + + stm32mp_cpu_lowlevel_init(); + + if (IS_ENABLED(CONFIG_DEBUG_LL)) + setup_uart(); + + fdt = __dtb_z_stm32mp15x_myirtech_myd_start + get_runtime_offset(); + + stm32mp1_barebox_entry(fdt); +} diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index 81e11bb6a3..b882c4942b 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -143,6 +143,7 @@ lwl-$(CONFIG_MACH_SEEED_ODYSSEY) += stm32mp157c-odyssey.dtb.o lwl-$(CONFIG_MACH_STM32MP15XX_DKX) += stm32mp157c-dk2.dtb.o stm32mp157a-dk1.dtb.o lwl-$(CONFIG_MACH_STM32MP13XX_DK) += stm32mp135f-dk.dtb.o lwl-$(CONFIG_MACH_LXA_MC1) += stm32mp157c-lxa-mc1.dtb.o +lwl-$(CONFIG_MACH_MYIRTECH_STM32MP1) += stm32mp15x-myirtech-myd.dtb.o lwl-$(CONFIG_MACH_STM32MP15X_EV1) += stm32mp157c-ev1.dtb.o lwl-$(CONFIG_MACH_SCB9328) += imx1-scb9328.dtb.o lwl-$(CONFIG_MACH_TECHNEXION_WANDBOARD) += imx6q-wandboard.dtb.o imx6dl-wandboard.dtb.o diff --git a/arch/arm/dts/stm32mp15x-myirtech-myc.dtsi b/arch/arm/dts/stm32mp15x-myirtech-myc.dtsi new file mode 100644 index 0000000000..7f843ad2ab --- /dev/null +++ b/arch/arm/dts/stm32mp15x-myirtech-myc.dtsi @@ -0,0 +1,351 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* SPDX-FileCopyrightText: Alexander Shiyan, <[email protected]> */ + +#include <arm/stm32mp151.dtsi> +#include <arm/stm32mp15-pinctrl.dtsi> +#include <arm/stm32mp15xxac-pinctrl.dtsi> + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/leds/common.h> +#include <dt-bindings/mfd/st,stpmic1.h> + +/ { + model = "MYIR MYC-YA15XC-T"; + compatible = "myir,myc-stm32mp15x", "st,stm32mp151"; + + aliases { + i2c0 = &i2c1; + i2c1 = &i2c2; + i2c2 = &i2c3; + i2c3 = &i2c4; + i2c4 = &i2c5; + i2c5 = &i2c6; + }; + + memory@c0000000 { + device_type = "memory"; + reg = <0xc0000000 0x10000000>; + }; + + reserved-memory { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + mcuram2: mcuram2@10000000 { + compatible = "shared-dma-pool"; + reg = <0x10000000 0x40000>; + no-map; + }; + + vdev0vring0: vdev0vring0@10040000 { + compatible = "shared-dma-pool"; + reg = <0x10040000 0x1000>; + no-map; + }; + + vdev0vring1: vdev0vring1@10041000 { + compatible = "shared-dma-pool"; + reg = <0x10041000 0x1000>; + no-map; + }; + + vdev0buffer: vdev0buffer@10042000 { + compatible = "shared-dma-pool"; + reg = <0x10042000 0x4000>; + no-map; + }; + + mcuram: mcuram@30000000 { + compatible = "shared-dma-pool"; + reg = <0x30000000 0x40000>; + no-map; + }; + + retram: retram@38000000 { + compatible = "shared-dma-pool"; + reg = <0x38000000 0x10000>; + no-map; + }; + + optee: optee@0xde000000 { + reg = <0xde000000 0x02000000>; + no-map; + }; + }; + + vin_som: vin_som { + compatible = "regulator-fixed"; + regulator-name = "vin_som"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + }; + + leds: leds { + compatible = "gpio-leds"; + + led_cpu: led_cpu { + label = "som:cpu"; + color = <LED_COLOR_ID_BLUE>; + default-state = "off"; + function = LED_FUNCTION_CPU; + gpios = <&gpioa 13 (GPIO_ACTIVE_LOW | GPIO_PUSH_PULL)>; + linux,default-trigger = LED_FUNCTION_CPU; + }; + }; +}; + +&bsec { + board_id: board_id@ec { + reg = <0xec 0x4>; + st,non-secure-otp; + }; +}; + +&cpu0 { + cpu-supply = <&vddcore>; +}; + +&dts { + status = "okay"; +}; + +&fmc { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&fmc_pins_a>; + pinctrl-1 = <&fmc_sleep_pins_a>; + status = "okay"; + + nand-controller@4,0 { + status = "okay"; + + nand@0 { + reg = <0>; + nand-on-flash-bbt; + nand-ecc-strength = <4>; + nand-ecc-step-size = <512>; + #address-cells = <1>; + #size-cells = <1>; + + nand_parts: partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "fsbl1"; + reg = <0x0 0x80000>; + }; + + partition@80000 { + label = "fsbl2"; + reg = <0x80000 0x80000>; + }; + + partition@100000 { + label = "matadata1"; + reg = <0x100000 0x80000>; + }; + + partition@180000 { + label = "matadata2"; + reg = <0x180000 0x80000>; + }; + + partition@200000 { + label = "fip-a1"; + reg = <0x200000 0x400000>; + }; + + partition@600000 { + label = "fip-a2"; + reg = <0x600000 0x400000>; + }; + + partition@a00000 { + label = "fip-b1"; + reg = <0xa00000 0x400000>; + }; + + partition@e00000 { + label = "fip-b2"; + reg = <0xe00000 0x400000>; + }; + + partition@1200000 { + label = "system"; + reg = <0x01200000 0>; + }; + }; + }; + }; +}; + +&i2c4 { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&i2c4_pins_a>; + pinctrl-1 = <&i2c4_sleep_pins_a>; + clock-frequency = <400000>; + status = "okay"; + + pmic: stpmic@33 { + compatible = "st,stpmic1"; + reg = <0x33>; + interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>; + interrupt-controller; + #interrupt-cells = <2>; + + regulators { + compatible = "st,stpmic1-regulators"; + buck1-supply = <&vin_som>; + buck2-supply = <&vin_som>; + buck3-supply = <&vin_som>; + buck4-supply = <&vin_som>; + ldo1-supply = <&v3v3>; + ldo4-supply = <&vin_som>; + vref_ddr-supply = <&vin_som>; + boost-supply = <&vin_som>; + pwr_sw1-supply = <&bst_out>; + pwr_sw2-supply = <&bst_out>; + + vddcore: buck1 { + regulator-name = "vddcore"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-initial-mode = <0>; + regulator-over-current-protection; + }; + + vdd_ddr: buck2 { + regulator-name = "vdd_ddr"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-initial-mode = <0>; + regulator-over-current-protection; + }; + + vdd: buck3 { + regulator-name = "vdd"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + st,mask-reset; + regulator-initial-mode = <0>; + regulator-over-current-protection; + }; + + v3v3: buck4 { + regulator-name = "v3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-over-current-protection; + regulator-initial-mode = <0>; + }; + + vdda: ldo1 { + regulator-name = "vdda"; + regulator-min-microvolt = <1700000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vtt_ddr: ldo3 { + regulator-name = "vtt_ddr"; + regulator-always-on; + }; + + vdd_usb: ldo4 { + regulator-name = "vdd_usb"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + vref_ddr: vref_ddr { + regulator-name = "vref_ddr"; + regulator-always-on; + regulator-over-current-protection; + }; + + bst_out: boost { + regulator-name = "bst_out"; + }; + + vbus_otg: pwr_sw1 { + regulator-name = "vbus_otg"; + regulator-active-discharge; + }; + + vbus_sw: pwr_sw2 { + regulator-name = "vbus_sw"; + regulator-active-discharge; + }; + }; + + onkey: onkey { + compatible = "st,stpmic1-onkey"; + interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 0>; + interrupt-names = "onkey-falling", "onkey-rising"; + power-off-time-sec = <10>; + }; + }; + + eeprom: eeprom@50 { + compatible = "atmel,24c32"; + reg = <0x50>; + pagesize = <32>; + num-addresses = <8>; + wp-gpios = <&gpioa 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + }; +}; + +&ipcc { + status = "okay"; +}; + +&iwdg2 { + timeout-sec = <32>; + status = "okay"; +}; + +&m4_rproc { + memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>, + <&vdev0vring1>, <&vdev0buffer>; + mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>, <&ipcc 3>; + mbox-names = "vq0", "vq1", "shutdown", "detach"; + interrupt-parent = <&exti>; + interrupts = <68 IRQ_TYPE_EDGE_RISING>; + status = "okay"; +}; + +&pwr_regulators { + vdd-supply = <&vdd>; + vdd_3v3_usbfs-supply = <&vdd_usb>; +}; + +&rng1 { + status = "okay"; +}; + +&rtc { + status = "okay"; +}; + +&sdmmc2 { + pinctrl-names = "default", "opendrain", "sleep"; + pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a>; + pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_a>; + pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_a>; + non-removable; + no-sd; + no-sdio; + st,neg-edge; + bus-width = <8>; + vmmc-supply = <&v3v3>; + vqmmc-supply = <&vdd>; + mmc-ddr-3_3v; + status = "okay"; +}; diff --git a/arch/arm/dts/stm32mp15x-myirtech-myd.dts b/arch/arm/dts/stm32mp15x-myirtech-myd.dts new file mode 100644 index 0000000000..b15a4312d4 --- /dev/null +++ b/arch/arm/dts/stm32mp15x-myirtech-myd.dts @@ -0,0 +1,458 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* SPDX-FileCopyrightText: Alexander Shiyan, <[email protected]> */ + +/dts-v1/; + +#include "stm32mp15x-myirtech-myc.dtsi" + +#include <dt-bindings/net/qca-ar803x.h> + +/ { + model = "MYIR MYD-YA15XC-T"; + compatible = "myir,myd-stm32mp15x", "myir,myc-stm32mp15x", "st,stm32mp151"; + + aliases { + ethernet0 = ðernet0; + serial0 = &uart4; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + backlight: backlight { + compatible = "pwm-backlight"; + pwms = <&pwm2 0 100000 0>; + brightness-levels = <0 255>; + num-interpolated-steps = <256>; + default-brightness-level = <255>; + }; + + panel: panel { + compatible = "panel-lvds"; + backlight = <&backlight>; + data-mapping = "vesa-24"; + enable-gpios = <&gpioi 3 (GPIO_ACTIVE_HIGH | GPIO_PUSH_PULL)>; + power-supply = <&vdd_3v3>; + height-mm = <0>; + width-mm = <0>; + + port { + panel_in: endpoint { + remote-endpoint = <<dc_ep0_out>; + }; + }; + }; + + vin: vin { + compatible = "regulator-fixed"; + regulator-name = "vin"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + }; + + vdd_3v3: vdd_3v3 { + compatible = "regulator-fixed"; + regulator-name = "vdd_3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + vin-supply = <&v3v3>; + }; +}; + +&leds { + led_live: led_live { + label = "board:live"; + color = <LED_COLOR_ID_BLUE>; + default-state = "off"; + function = LED_FUNCTION_HEARTBEAT; + gpios = <&extgpio 4 GPIO_ACTIVE_LOW>; + linux,default-trigger = LED_FUNCTION_HEARTBEAT; + panic-indicator; + }; +}; + +&vin_som { + vin-supply = <&vin>; +}; + +&i2c2 { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&i2c2_pins &i2c2_pins_z>; + pinctrl-1 = <&i2c2_sleep_pins &i2c2_sleep_pins_z>; + clock-frequency = <400000>; + status = "okay"; + + extgpio: pcf8575@20 { + compatible = "nxp,pcf8575"; + reg = <0x20>; + gpio-controller; + #gpio-cells = <2>; + }; + + typec: stusb1600@28 { + pinctrl-names = "default"; + pinctrl-0 = <&stusb1600_pins>; + compatible = "st,stusb1600"; + reg = <0x28>; + interrupt-parent = <&gpioa>; + interrupts = <10 IRQ_TYPE_EDGE_FALLING>; + vdd-supply = <&vin>; + + connector { + compatible = "usb-c-connector"; + label = "USB-C"; + power-role = "dual"; + power-opmode = "default"; + + port { + con_usbotg_hs_ep: endpoint { + remote-endpoint = <&usbotg_hs_ep>; + }; + }; + }; + }; + + rx8025: rtc@32 { + compatible = "epson,rx8025"; + reg = <0x32>; + }; +}; + +ðernet0 { + pinctrl-0 = <ðernet0_rgmii_pins_a>; + pinctrl-1 = <ðernet0_rgmii_sleep_pins_a>; + pinctrl-names = "default", "sleep"; + max-speed = <1000>; + phy-handle = <&phy0>; + phy-mode = "rgmii-id"; + status = "okay"; + + mdio { + compatible = "snps,dwmac-mdio"; + reset-gpios = <&gpiog 3 (GPIO_ACTIVE_LOW | GPIO_PUSH_PULL)>; + reset-delay-us = <10000>; + reset-post-delay-us = <2000>; + + #address-cells = <1>; + #size-cells = <0>; + + phy0: ethernet-phy@6 { + reg = <6>; + qca,clk-out-frequency = <125000000>; + qca,clk-out-strength = <AR803X_STRENGTH_FULL>; + }; + }; +}; + +<dc { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <<dc_pins>; + pinctrl-1 = <<dc_sleep_pins>; + status = "okay"; + + port { + ltdc_ep0_out: endpoint@0 { + reg = <0>; + remote-endpoint = <&panel_in>; + }; + }; +}; + +&sai1 { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&sai1_pins>; + pinctrl-1 = <&sai1_sleep_pins>; + clocks = <&rcc SAI1>, <&rcc PLL3_Q>, <&rcc PLL3_R>; + clock-names = "pclk", "x8k", "x11k"; + status = "okay"; +}; + +&sdmmc1 { + pinctrl-names = "default", "opendrain", "sleep"; + pinctrl-0 = <&sdmmc1_b4_pins_a>; + pinctrl-1 = <&sdmmc1_b4_od_pins_a>; + pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>; + cd-gpios = <&gpioa 3 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; + disable-wp; + st,neg-edge; + vmmc-supply = <&vdd>; + status = "okay"; +}; + +&spi5 { + pinctrl-names = "default"; + pinctrl-0 = <&spi5_pins>; + cs-gpios = <&gpioh 5 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>, + <&gpiof 13 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; + status = "okay"; +}; + +&timers2 { + status = "okay"; + + pwm2: pwm { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&tim2_pwm_pins>; + pinctrl-1 = <&tim2_pwm_sleep_pins>; + status = "okay"; + }; +}; + +&uart4 { + pinctrl-names = "default", "sleep", "idle"; + pinctrl-0 = <&uart4_pins>; + pinctrl-1 = <&uart4_sleep_pins>; + pinctrl-2 = <&uart4_idle_pins>; + status = "okay"; +}; + +&usbh_ehci { + phys = <&usbphyc_port0>; + phy-names = "usb"; + status = "okay"; +}; + +&usbotg_hs { + phys = <&usbphyc_port1 0>; + phy-names = "usb2-phy"; + usb-role-switch; + vbus-supply = <&vbus_otg>; + status = "okay"; + + port { + usbotg_hs_ep: endpoint { + remote-endpoint = <&con_usbotg_hs_ep>; + }; + }; +}; + +&usbphyc { + status = "okay"; +}; + +&usbphyc_port0 { + phy-supply = <&vdd_usb>; + st,tune-hs-dc-level = <2>; + st,enable-fs-rftime-tuning; + st,enable-hs-rftime-reduction; + st,trim-hs-current = <15>; + st,trim-hs-impedance = <1>; + st,tune-squelch-level = <3>; + st,tune-hs-rx-offset = <2>; + st,no-lsfs-sc; + + connector { + compatible = "usb-a-connector"; + vbus-supply = <&vin>; + }; +}; + +&usbphyc_port1 { + phy-supply = <&vdd_usb>; + st,tune-hs-dc-level = <2>; + st,enable-fs-rftime-tuning; + st,enable-hs-rftime-reduction; + st,trim-hs-current = <15>; + st,trim-hs-impedance = <1>; + st,tune-squelch-level = <3>; + st,tune-hs-rx-offset = <2>; + st,no-lsfs-sc; +}; + +&pinctrl { + i2c2_pins: i2c2-0 { + pins { + pinmux = <STM32_PINMUX('H', 4, AF4)>; /* I2C2_SCL */ + bias-disable; + drive-open-drain; + slew-rate = <0>; + }; + }; + + i2c2_sleep_pins: i2c2-sleep-0 { + pins { + pinmux = <STM32_PINMUX('H', 4, ANALOG)>; /* I2C2_SCL */ + }; + }; + + ltdc_pins: ltdc-0 { + pins { + pinmux = <STM32_PINMUX('G', 7, AF14)>, /* LCD_CLK */ + <STM32_PINMUX('I', 10, AF14)>, /* LCD_HSYNC */ + <STM32_PINMUX('I', 9, AF14)>, /* LCD_VSYNC */ + <STM32_PINMUX('E', 13, AF14)>, /* LCD_DE */ + <STM32_PINMUX('H', 2, AF14)>, /* LCD_R0 */ + <STM32_PINMUX('H', 3, AF14)>, /* LCD_R1 */ + <STM32_PINMUX('H', 8, AF14)>, /* LCD_R2 */ + <STM32_PINMUX('H', 9, AF14)>, /* LCD_R3 */ + <STM32_PINMUX('H', 10, AF14)>, /* LCD_R4 */ + <STM32_PINMUX('H', 11, AF14)>, /* LCD_R5 */ + <STM32_PINMUX('H', 12, AF14)>, /* LCD_R6 */ + <STM32_PINMUX('E', 15, AF14)>, /* LCD_R7 */ + <STM32_PINMUX('E', 14, AF14)>, /* LCD_G0 */ + <STM32_PINMUX('E', 6, AF14)>, /* LCD_G1 */ + <STM32_PINMUX('H', 13, AF14)>, /* LCD_G2 */ + <STM32_PINMUX('H', 14, AF14)>, /* LCD_G3 */ + <STM32_PINMUX('H', 15, AF14)>, /* LCD_G4 */ + <STM32_PINMUX('I', 0, AF14)>, /* LCD_G5 */ + <STM32_PINMUX('I', 1, AF14)>, /* LCD_G6 */ + <STM32_PINMUX('I', 2, AF14)>, /* LCD_G7 */ + <STM32_PINMUX('D', 9, AF14)>, /* LCD_B0 */ + <STM32_PINMUX('G', 12, AF14)>, /* LCD_B1 */ + <STM32_PINMUX('G', 10, AF14)>, /* LCD_B2 */ + <STM32_PINMUX('D', 10, AF14)>, /* LCD_B3 */ + <STM32_PINMUX('I', 4, AF14)>, /* LCD_B4 */ + <STM32_PINMUX('I', 5, AF14)>, /* LCD_B5 */ + <STM32_PINMUX('I', 6, AF14)>, /* LCD_B6 */ + <STM32_PINMUX('I', 7, AF14)>; /* LCD_B7 */ + bias-disable; + drive-push-pull; + slew-rate = <1>; + }; + }; + + ltdc_sleep_pins: ltdc-sleep-0 { + pins { + pinmux = <STM32_PINMUX('G', 7, ANALOG)>, /* LCD_CLK */ + <STM32_PINMUX('I', 10, ANALOG)>, /* LCD_HSYNC */ + <STM32_PINMUX('I', 9, ANALOG)>, /* LCD_VSYNC */ + <STM32_PINMUX('E', 13, ANALOG)>, /* LCD_DE */ + <STM32_PINMUX('H', 2, ANALOG)>, /* LCD_R0 */ + <STM32_PINMUX('H', 3, ANALOG)>, /* LCD_R1 */ + <STM32_PINMUX('H', 8, ANALOG)>, /* LCD_R2 */ + <STM32_PINMUX('H', 9, ANALOG)>, /* LCD_R3 */ + <STM32_PINMUX('H', 10, ANALOG)>, /* LCD_R4 */ + <STM32_PINMUX('H', 11, ANALOG)>, /* LCD_R5 */ + <STM32_PINMUX('H', 12, ANALOG)>, /* LCD_R6 */ + <STM32_PINMUX('E', 15, ANALOG)>, /* LCD_R7 */ + <STM32_PINMUX('E', 14, ANALOG)>, /* LCD_G0 */ + <STM32_PINMUX('E', 6, ANALOG)>, /* LCD_G1 */ + <STM32_PINMUX('H', 13, ANALOG)>, /* LCD_G2 */ + <STM32_PINMUX('H', 14, ANALOG)>, /* LCD_G3 */ + <STM32_PINMUX('H', 15, ANALOG)>, /* LCD_G4 */ + <STM32_PINMUX('I', 0, ANALOG)>, /* LCD_G5 */ + <STM32_PINMUX('I', 1, ANALOG)>, /* LCD_G6 */ + <STM32_PINMUX('I', 2, ANALOG)>, /* LCD_G7 */ + <STM32_PINMUX('D', 9, ANALOG)>, /* LCD_B0 */ + <STM32_PINMUX('G', 12, ANALOG)>, /* LCD_B1 */ + <STM32_PINMUX('G', 10, ANALOG)>, /* LCD_B2 */ + <STM32_PINMUX('D', 10, ANALOG)>, /* LCD_B3 */ + <STM32_PINMUX('I', 4, ANALOG)>, /* LCD_B4 */ + <STM32_PINMUX('I', 5, ANALOG)>, /* LCD_B5 */ + <STM32_PINMUX('I', 6, ANALOG)>, /* LCD_B6 */ + <STM32_PINMUX('I', 7, ANALOG)>; /* LCD_B7 */ + }; + }; + + sai1_pins: sai1-0 { + pins1 { + pinmux = <STM32_PINMUX('B', 2, AF6)>, /* SAI1_SD_A */ + <STM32_PINMUX('F', 8, AF6)>, /* SAI1_SCK_B */ + <STM32_PINMUX('F', 9, AF6)>, /* SAI1_FS_B */ + <STM32_PINMUX('F', 7, AF6)>; /* SAI1_MCLK_B */ + slew-rate = <0>; + drive-push-pull; + bias-disable; + }; + pins2 { + pinmux = <STM32_PINMUX('F', 6, AF6)>; /* SAI1_SD_B */ + bias-disable; + }; + }; + + sai1_sleep_pins: sai1-sleep-0 { + pins { + pinmux = <STM32_PINMUX('B', 2, ANALOG)>, /* SAI1_SD_A */ + <STM32_PINMUX('F', 8, ANALOG)>, /* SAI1_SCK_B */ + <STM32_PINMUX('F', 9, ANALOG)>, /* SAI1_FS_B */ + <STM32_PINMUX('F', 7, ANALOG)>, /* SAI1_MCLK_B */ + <STM32_PINMUX('F', 6, ANALOG)>; /* SAI1_SD_B */ + }; + }; + + spi5_pins: spi5-0 { + pins { + pinmux = <STM32_PINMUX('H', 6, AF5)>, /* SPI5_SCK */ + <STM32_PINMUX('F', 11, AF5)>; /* SPI5_MOSI */ + bias-disable; + drive-push-pull; + slew-rate = <1>; + }; + pins2 { + pinmux = <STM32_PINMUX('H', 7, AF5)>; /* SPI5_MISO */ + bias-disable; + }; + }; + + stusb1600_pins: stusb1600-0 { + pins { + pinmux = <STM32_PINMUX('A', 10, ANALOG)>; /* STUSB1600 IRQ */ + bias-pull-up; + }; + }; + + tim2_pwm_pins: tim2-pwm-0 { + pins { + pinmux = <STM32_PINMUX('G', 8, AF1)>; /* TIM2_CH1 */ + bias-disable; + drive-push-pull; + slew-rate = <0>; + }; + }; + + tim2_pwm_sleep_pins: tim2-pwm-sleep-0 { + pins { + pinmux = <STM32_PINMUX('G', 8, ANALOG)>; /* TIM2_CH1 */ + }; + }; + + uart4_pins: uart4-0 { + pins1 { + pinmux = <STM32_PINMUX('G', 11, AF6)>; /* UART4_TX */ + bias-disable; + drive-push-pull; + slew-rate = <0>; + }; + pins2 { + pinmux = <STM32_PINMUX('A', 11, AF6)>; /* UART4_RX */ + bias-disable; + }; + }; + + uart4_idle_pins: uart4-idle-0 { + pins1 { + pinmux = <STM32_PINMUX('G', 11, ANALOG)>; /* UART4_TX */ + }; + pins2 { + pinmux = <STM32_PINMUX('A', 11, AF6)>; /* UART4_RX */ + bias-disable; + }; + }; + + uart4_sleep_pins: uart4-sleep-0 { + pins1 { + pinmux = <STM32_PINMUX('G', 11, ANALOG)>, /* UART4_TX */ + <STM32_PINMUX('A', 11, ANALOG)>; /* UART4_RX */ + }; + }; +}; + +&pinctrl_z { + i2c2_pins_z: i2c2-0 { + pins { + pinmux = <STM32_PINMUX('Z', 7, AF3)>; /* I2C2_SDA */ + bias-disable; + drive-open-drain; + slew-rate = <0>; + }; + }; + + i2c2_sleep_pins_z: i2c2-sleep-0 { + pins { + pinmux = <STM32_PINMUX('Z', 7, ANALOG)>; /* I2C2_SDA */ + }; + }; +}; diff --git a/arch/arm/mach-stm32mp/Kconfig b/arch/arm/mach-stm32mp/Kconfig index bc0a48d64c..358aad940c 100644 --- a/arch/arm/mach-stm32mp/Kconfig +++ b/arch/arm/mach-stm32mp/Kconfig @@ -29,6 +29,13 @@ config MACH_LXA_MC1 select ARCH_STM32MP157 bool "Linux Automation MC-1 board" +config MACH_MYIRTECH_STM32MP1 + bool "MYIR Tech Limited SOMs" + select ARCH_STM32MP157 + select MACHINE_ID + help + Say Y here if you are using a STM32MP15x based MYIR SOM + config MACH_SEEED_ODYSSEY select ARCH_STM32MP157 bool "Seeed Studio Odyssey" diff --git a/images/Makefile.stm32mp b/images/Makefile.stm32mp index 59d6572207..344dd41eb7 100644 --- a/images/Makefile.stm32mp +++ b/images/Makefile.stm32mp @@ -36,6 +36,8 @@ $(call build_stm32mp_image, CONFIG_MACH_STM32MP15X_EV1, start_stm32mp15x_ev1, st $(call build_stm32mp_image, CONFIG_MACH_LXA_MC1, start_stm32mp157c_lxa_mc1, stm32mp157c-lxa-mc1) +$(call build_stm32mp_image, CONFIG_MACH_MYIRTECH_STM32MP1, start_stm32mp15x_myir, stm32mp15x-myir) + $(call build_stm32mp_image, CONFIG_MACH_PROTONIC_STM32MP1, start_prtt1a, prtt1a) $(call build_stm32mp_image, CONFIG_MACH_PROTONIC_STM32MP1, start_prtt1s, prtt1s) $(call build_stm32mp_image, CONFIG_MACH_PROTONIC_STM32MP1, start_prtt1c, prtt1c) -- 2.39.1
