None of the PXA boards has PBL support. This becomes mandatory soon, so remove the boards.
Signed-off-by: Sascha Hauer <[email protected]> --- arch/arm/boards/Makefile | 5 - arch/arm/boards/lubbock/Makefile | 4 - arch/arm/boards/lubbock/board.c | 118 ----- arch/arm/boards/lubbock/env/boot/nor-ubi | 5 - arch/arm/boards/lubbock/env/init/mtdparts-nor | 6 - .../lubbock/env/nv/linux.bootargs.console | 1 - arch/arm/boards/lubbock/lowlevel.c | 194 -------- arch/arm/boards/mainstone/Makefile | 4 - arch/arm/boards/mainstone/board.c | 118 ----- arch/arm/boards/mainstone/env/boot/nor-ubi | 5 - .../boards/mainstone/env/init/mtdparts-nor | 6 - .../mainstone/env/nv/linux.bootargs.console | 1 - arch/arm/boards/mainstone/lowlevel.c | 266 ----------- arch/arm/boards/mioa701/Makefile | 4 - arch/arm/boards/mioa701/board.c | 274 ----------- .../arm/boards/mioa701/env/bin/barebox_update | 11 - arch/arm/boards/mioa701/env/bin/console_mode | 6 - arch/arm/boards/mioa701/env/bin/dps1_unlock | 12 - arch/arm/boards/mioa701/env/bin/dps1_update | 12 - arch/arm/boards/mioa701/env/bin/init | 79 --- .../boards/mioa701/env/bin/mtd_env_override | 4 - .../boards/mioa701/env/bin/sdcard_override | 19 - arch/arm/boards/mioa701/env/config | 6 - arch/arm/boards/mioa701/env/data/dps1.raw.gz | Bin 1324 -> 0 bytes arch/arm/boards/mioa701/gpio0_poweroff.c | 67 --- arch/arm/boards/mioa701/lowlevel.c | 12 - arch/arm/boards/mioa701/mioa701.h | 67 --- .../arm/boards/phytec-phycore-pxa270/Makefile | 4 - arch/arm/boards/phytec-phycore-pxa270/board.c | 171 ------- .../arm/boards/phytec-phycore-pxa270/config.h | 314 ------------ .../env/init/mtdparts-nor | 6 - .../env/nv/linux.bootargs.console | 1 - .../phytec-phycore-pxa270/lowlevel_init.S | 448 ------------------ arch/arm/boards/zylonite/Makefile | 4 - arch/arm/boards/zylonite/board.c | 93 ---- arch/arm/boards/zylonite/env/boot/nand-ubi | 5 - .../boards/zylonite/env/init/mtdparts-nand | 6 - arch/arm/boards/zylonite/env/nv/hostname | 1 - .../zylonite/env/nv/linux.bootargs.base | 1 - .../zylonite/env/nv/linux.bootargs.console | 1 - arch/arm/boards/zylonite/lowlevel.c | 12 - arch/arm/configs/lubbock_defconfig | 100 ---- arch/arm/configs/mainstone_defconfig | 103 ---- arch/arm/configs/mioa701_defconfig | 104 ---- .../configs/phytec-phycore-pxa270_defconfig | 60 --- arch/arm/configs/zylonite310_defconfig | 104 ---- arch/arm/include/asm/mach-types.h | 60 --- arch/arm/mach-pxa/Kconfig | 87 ---- 48 files changed, 2991 deletions(-) delete mode 100644 arch/arm/boards/lubbock/Makefile delete mode 100644 arch/arm/boards/lubbock/board.c delete mode 100644 arch/arm/boards/lubbock/env/boot/nor-ubi delete mode 100644 arch/arm/boards/lubbock/env/init/mtdparts-nor delete mode 100644 arch/arm/boards/lubbock/env/nv/linux.bootargs.console delete mode 100644 arch/arm/boards/lubbock/lowlevel.c delete mode 100644 arch/arm/boards/mainstone/Makefile delete mode 100644 arch/arm/boards/mainstone/board.c delete mode 100644 arch/arm/boards/mainstone/env/boot/nor-ubi delete mode 100644 arch/arm/boards/mainstone/env/init/mtdparts-nor delete mode 100644 arch/arm/boards/mainstone/env/nv/linux.bootargs.console delete mode 100644 arch/arm/boards/mainstone/lowlevel.c delete mode 100644 arch/arm/boards/mioa701/Makefile delete mode 100644 arch/arm/boards/mioa701/board.c delete mode 100644 arch/arm/boards/mioa701/env/bin/barebox_update delete mode 100644 arch/arm/boards/mioa701/env/bin/console_mode delete mode 100644 arch/arm/boards/mioa701/env/bin/dps1_unlock delete mode 100644 arch/arm/boards/mioa701/env/bin/dps1_update delete mode 100644 arch/arm/boards/mioa701/env/bin/init delete mode 100644 arch/arm/boards/mioa701/env/bin/mtd_env_override delete mode 100644 arch/arm/boards/mioa701/env/bin/sdcard_override delete mode 100644 arch/arm/boards/mioa701/env/config delete mode 100644 arch/arm/boards/mioa701/env/data/dps1.raw.gz delete mode 100644 arch/arm/boards/mioa701/gpio0_poweroff.c delete mode 100644 arch/arm/boards/mioa701/lowlevel.c delete mode 100644 arch/arm/boards/mioa701/mioa701.h delete mode 100644 arch/arm/boards/phytec-phycore-pxa270/Makefile delete mode 100644 arch/arm/boards/phytec-phycore-pxa270/board.c delete mode 100644 arch/arm/boards/phytec-phycore-pxa270/config.h delete mode 100644 arch/arm/boards/phytec-phycore-pxa270/env/init/mtdparts-nor delete mode 100644 arch/arm/boards/phytec-phycore-pxa270/env/nv/linux.bootargs.console delete mode 100644 arch/arm/boards/phytec-phycore-pxa270/lowlevel_init.S delete mode 100644 arch/arm/boards/zylonite/Makefile delete mode 100644 arch/arm/boards/zylonite/board.c delete mode 100644 arch/arm/boards/zylonite/env/boot/nand-ubi delete mode 100644 arch/arm/boards/zylonite/env/init/mtdparts-nand delete mode 100644 arch/arm/boards/zylonite/env/nv/hostname delete mode 100644 arch/arm/boards/zylonite/env/nv/linux.bootargs.base delete mode 100644 arch/arm/boards/zylonite/env/nv/linux.bootargs.console delete mode 100644 arch/arm/boards/zylonite/lowlevel.c delete mode 100644 arch/arm/configs/lubbock_defconfig delete mode 100644 arch/arm/configs/mainstone_defconfig delete mode 100644 arch/arm/configs/mioa701_defconfig delete mode 100644 arch/arm/configs/phytec-phycore-pxa270_defconfig delete mode 100644 arch/arm/configs/zylonite310_defconfig diff --git a/arch/arm/boards/Makefile b/arch/arm/boards/Makefile index 022ba9903a..fc7a829900 100644 --- a/arch/arm/boards/Makefile +++ b/arch/arm/boards/Makefile @@ -56,11 +56,8 @@ obj-$(CONFIG_MACH_KAMSTRUP_MX7_CONCENTRATOR) += kamstrup-mx7-concentrator/ obj-$(CONFIG_MACH_KARO_QSXP_ML81) += karo-qsxp-ml81/ obj-$(CONFIG_MACH_KONTRON_SAMX6I) += kontron-samx6i/ obj-$(CONFIG_MACH_LENOVO_IX4_300D) += lenovo-ix4-300d/ -obj-$(CONFIG_MACH_LUBBOCK) += lubbock/ -obj-$(CONFIG_MACH_MAINSTONE) += mainstone/ obj-$(CONFIG_MACH_MARVELL_ARMADA_XP_GP) += marvell-armada-xp-gp/ obj-$(CONFIG_MACH_MARVELL_ARMADA_XP_DB) += marvell-armada-xp-db/ -obj-$(CONFIG_MACH_MIOA701) += mioa701/ obj-$(CONFIG_MACH_MX23EVK) += freescale-mx23-evk/ obj-$(CONFIG_MACH_MX28EVK) += freescale-mx28-evk/ obj-$(CONFIG_MACH_MYIRTECH_X335X) += myirtech-x335x/ @@ -82,7 +79,6 @@ obj-$(CONFIG_MACH_PANDA) += panda/ obj-$(CONFIG_MACH_PCA100) += phytec-phycard-imx27/ obj-$(CONFIG_MACH_PCAAL1) += phytec-phycard-omap3/ obj-$(CONFIG_MACH_PCAAXL2) += phytec-phycard-omap4/ -obj-$(CONFIG_MACH_PCM027) += phytec-phycore-pxa270/ obj-$(CONFIG_MACH_PCM038) += phytec-phycore-imx27/ obj-$(CONFIG_MACH_PCM049) += phytec-phycore-omap4460/ obj-$(CONFIG_MACH_PHYTEC_SOM_AM335X) += phytec-som-am335x/ @@ -162,7 +158,6 @@ obj-$(CONFIG_MACH_USI_TOPKICK) += usi-topkick/ obj-$(CONFIG_MACH_VERSATILEPB) += versatile/ obj-$(CONFIG_MACH_VEXPRESS) += vexpress/ obj-$(CONFIG_MACH_ZEDBOARD) += avnet-zedboard/ -obj-$(CONFIG_MACH_ZYLONITE) += zylonite/ obj-$(CONFIG_MACH_VARISCITE_MX6) += variscite-mx6/ obj-$(CONFIG_MACH_VARISCITE_SOM_MX7) += variscite-som-mx7/ obj-$(CONFIG_MACH_VSCOM_BALTOS) += vscom-baltos/ diff --git a/arch/arm/boards/lubbock/Makefile b/arch/arm/boards/lubbock/Makefile deleted file mode 100644 index da63d2625f..0000000000 --- a/arch/arm/boards/lubbock/Makefile +++ /dev/null @@ -1,4 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0-only - -obj-y += board.o -lwl-y += lowlevel.o diff --git a/arch/arm/boards/lubbock/board.c b/arch/arm/boards/lubbock/board.c deleted file mode 100644 index af046e110a..0000000000 --- a/arch/arm/boards/lubbock/board.c +++ /dev/null @@ -1,118 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-or-later -// SPDX-FileCopyrightText: 2011 Robert Jarzmik <[email protected]> - -#include <common.h> -#include <driver.h> -#include <environment.h> -#include <fs.h> -#include <init.h> -#include <led.h> -#include <gpio.h> -#include <pwm.h> -#include <linux/sizes.h> - -#include <mach/pxa/devices.h> -#include <mach/pxa/mfp-pxa27x.h> -#include <mach/pxa/pxa-regs.h> -#include <mach/pxa/udc_pxa2xx.h> -#include <mach/pxa/mci_pxa2xx.h> - -#include <platform_data/eth-smc91111.h> -#include <asm/armlinux.h> -#include <asm/io.h> -#include <asm/mmu.h> - -#include <asm/mach-types.h> - -#define ECOR 0x8000 -#define ECOR_RESET 0x80 -#define ECOR_LEVEL_IRQ 0x40 -#define ECOR_WR_ATTRIB 0x04 -#define ECOR_ENABLE 0x01 - -#define ECSR 0x8002 -#define ECSR_IOIS8 0x20 -#define ECSR_PWRDWN 0x04 -#define ECSR_INT 0x02 - -static struct smc91c111_pdata smsc91x_pdata = { - .control_setup = 0x0800, - .config_setup = 0x10b2, - .bus_width = 16, - .addr_shift = 2, -}; - -static unsigned long lubbock_pin_config[] = { - GPIO15_nCS_1, /* CS1 - Flash */ - GPIO78_nCS_2, /* CS2 - Baseboard FGPA + SRAM */ - GPIO79_nCS_3, /* CS3 - SMC ethernet */ - GPIO80_nCS_4, /* CS4 - SA1111 */ - - /* LCD - 16bpp DSTN */ - GPIOxx_LCD_DSTN_16BPP, - - /* FFUART */ - GPIO34_FFUART_RXD, - GPIO35_FFUART_CTS, - GPIO36_FFUART_DCD, - GPIO37_FFUART_DSR, - GPIO38_FFUART_RI, - GPIO39_FFUART_TXD, - GPIO40_FFUART_DTR, - GPIO41_FFUART_RTS, -}; - -static int lubbock_devices_init(void) -{ - void *nor0_iospace; - - armlinux_set_architecture(MACH_TYPE_LUBBOCK); - - pxa_add_uart((void *)0x40100000, 0); - pxa_add_pwm((void *)0x40b00000, 0); - - nor0_iospace = map_io_sections(0x0, (void *)0xe0000000, SZ_64M); - add_cfi_flash_device(0, (ulong)nor0_iospace, SZ_64M, 0); - add_cfi_flash_device(1, 0x04000000, SZ_64M, 0); - devfs_add_partition("nor0", SZ_2M, SZ_256K, DEVFS_PARTITION_FIXED, - "env0"); - add_generic_device("smc91c111", DEVICE_ID_DYNAMIC, NULL, - 0x0c000300, 0xff4000, IORESOURCE_MEM, - &smsc91x_pdata); - return 0; -} - -device_initcall(lubbock_devices_init); - -static void smc_init(void) -{ - /* SMC91c96 */ - void __iomem *attaddr = (void __iomem *)0x0e000000; - - writel(ECOR_RESET, attaddr + (ECOR << 2)); - mdelay(100); - writel(0, attaddr + (ECOR << 2)); - writel(ECOR_ENABLE, attaddr + (ECOR << 2)); - - /* force 16-bit mode */ - writel(0, attaddr + (ECSR << 2)); - mdelay(100); -} - -static int lubbock_coredevice_init(void) -{ - barebox_set_model("Lubbock PXA25x"); - barebox_set_hostname("lubbock"); - pxa2xx_mfp_config(ARRAY_AND_SIZE(lubbock_pin_config)); - smc_init(); - return 0; -} -coredevice_initcall(lubbock_coredevice_init); - -static int lubbock_mem_init(void) -{ - arm_add_mem_device("ram0", 0xa0000000, SZ_64M); - add_mem_device("sram0", 0x0a000000, SZ_1M, IORESOURCE_MEM_WRITEABLE); - return 0; -} -mem_initcall(lubbock_mem_init); diff --git a/arch/arm/boards/lubbock/env/boot/nor-ubi b/arch/arm/boards/lubbock/env/boot/nor-ubi deleted file mode 100644 index 533605e86a..0000000000 --- a/arch/arm/boards/lubbock/env/boot/nor-ubi +++ /dev/null @@ -1,5 +0,0 @@ -#!/bin/sh - -global.bootm.image="/dev/nor0.kernel" -#global.bootm.oftree="/env/oftree" -global.linux.bootargs.dyn.root="root=ubi0:linux_root ubi.mtd=nor0.root rootfstype=ubifs" diff --git a/arch/arm/boards/lubbock/env/init/mtdparts-nor b/arch/arm/boards/lubbock/env/init/mtdparts-nor deleted file mode 100644 index b5c4e32411..0000000000 --- a/arch/arm/boards/lubbock/env/init/mtdparts-nor +++ /dev/null @@ -1,6 +0,0 @@ -#!/bin/sh - -mtdparts="2048k@0(nor0.barebox)ro,256k(nor0.barebox-env),256k(nor0.barebox-logo),256k(nor0.barebox-logo2),5120k(nor0.kernel),-(nor0.root)" -kernelname="application-flash" - -mtdparts-add -d nor0 -k ${kernelname} -p ${mtdparts} diff --git a/arch/arm/boards/lubbock/env/nv/linux.bootargs.console b/arch/arm/boards/lubbock/env/nv/linux.bootargs.console deleted file mode 100644 index 476b1fbe49..0000000000 --- a/arch/arm/boards/lubbock/env/nv/linux.bootargs.console +++ /dev/null @@ -1 +0,0 @@ -console=ttyS0,115200 diff --git a/arch/arm/boards/lubbock/lowlevel.c b/arch/arm/boards/lubbock/lowlevel.c deleted file mode 100644 index ef6b544a26..0000000000 --- a/arch/arm/boards/lubbock/lowlevel.c +++ /dev/null @@ -1,194 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-only - -#include <common.h> -#include <init.h> -#include <io.h> - -#include <asm/barebox-arm-head.h> -#include <asm/barebox-arm.h> -#include <linux/sizes.h> -#include <mach/pxa/pxa-regs.h> -#include <mach/pxa/regs-ost.h> - -/* - * Memory settings - */ -#define DEFAULT_MSC0_VAL 0x23d223d2 -#define DEFAULT_MSC1_VAL 0x3ff1a441 -#define DEFAULT_MSC2_VAL 0x7ff17ff1 -#define DEFAULT_MDCNFG_VAL 0x00001ac9 -#define DEFAULT_MDREFR_VAL 0x00018018 -#define DEFAULT_MDMRS_VAL 0x00000000 - -#define DEFAULT_FLYCNFG_VAL 0x00000000 -#define DEFAULT_SXCNFG_VAL 0x00000000 - -/* - * PCMCIA and CF Interfaces - */ -#define DEFAULT_MECR_VAL 0x00000000 -#define DEFAULT_MCMEM0_VAL 0x00010504 -#define DEFAULT_MCMEM1_VAL 0x00010504 -#define DEFAULT_MCATT0_VAL 0x00010504 -#define DEFAULT_MCATT1_VAL 0x00010504 -#define DEFAULT_MCIO0_VAL 0x00004715 -#define DEFAULT_MCIO1_VAL 0x00004715 - -static inline void writelrb(uint32_t val, volatile u32 __iomem *addr) -{ - writel(val, addr); - barrier(); - readl(addr); - barrier(); -} - -static inline void pxa_wait_ticks(int ticks) -{ - writel(0, &OSCR); - while (readl(&OSCR) < ticks) - barrier(); -} - -static inline void pxa2xx_dram_init(void) -{ - uint32_t tmp; - int i; - /* - * 1) Initialize Asynchronous static memory controller - */ - - writelrb(DEFAULT_MSC0_VAL, &MSC0); - writelrb(DEFAULT_MSC1_VAL, &MSC1); - writelrb(DEFAULT_MSC2_VAL, &MSC2); - /* - * 2) Initialize Card Interface - */ - - /* MECR: Memory Expansion Card Register */ - writelrb(DEFAULT_MECR_VAL, &MECR); - /* MCMEM0: Card Interface slot 0 timing */ - writelrb(DEFAULT_MCMEM0_VAL, &MCMEM0); - /* MCMEM1: Card Interface slot 1 timing */ - writelrb(DEFAULT_MCMEM1_VAL, &MCMEM1); - /* MCATT0: Card Interface Attribute Space Timing, slot 0 */ - writelrb(DEFAULT_MCATT0_VAL, &MCATT0); - /* MCATT1: Card Interface Attribute Space Timing, slot 1 */ - writelrb(DEFAULT_MCATT1_VAL, &MCATT1); - /* MCIO0: Card Interface I/O Space Timing, slot 0 */ - writelrb(DEFAULT_MCIO0_VAL, &MCIO0); - /* MCIO1: Card Interface I/O Space Timing, slot 1 */ - writelrb(DEFAULT_MCIO1_VAL, &MCIO1); - - /* - * 3) Configure Fly-By DMA register - */ - - writelrb(DEFAULT_FLYCNFG_VAL, &FLYCNFG); - - /* - * 4) Initialize Timing for Sync Memory (SDCLK0) - */ - - /* - * Before accessing MDREFR we need a valid DRI field, so we set - * this to power on defaults + DRI field. - */ - - /* Read current MDREFR config and zero out DRI */ - tmp = readl(&MDREFR) & ~0xfff; - /* Add user-specified DRI */ - tmp |= DEFAULT_MDREFR_VAL & 0xfff; - /* Configure important bits */ - tmp |= MDREFR_K0RUN | MDREFR_SLFRSH; - tmp &= ~(MDREFR_APD | MDREFR_E1PIN); - - /* Write MDREFR back */ - writelrb(tmp, &MDREFR); - - /* - * 5) Initialize Synchronous Static Memory (Flash/Peripherals) - */ - - /* Initialize SXCNFG register. Assert the enable bits. - * - * Write SXMRS to cause an MRS command to all enabled banks of - * synchronous static memory. Note that SXLCR need not be written - * at this time. - */ - writelrb(DEFAULT_SXCNFG_VAL, &SXCNFG); - - /* - * 6) Initialize SDRAM - */ - - writelrb(DEFAULT_MDREFR_VAL & ~MDREFR_SLFRSH, &MDREFR); - writelrb(DEFAULT_MDREFR_VAL | MDREFR_E1PIN, &MDREFR); - - /* - * 7) Write MDCNFG with MDCNFG:DEx deasserted (set to 0), to configure - * but not enable each SDRAM partition pair. - */ - - writelrb(DEFAULT_MDCNFG_VAL & - ~(MDCNFG_DE0 | MDCNFG_DE1 | MDCNFG_DE2 | MDCNFG_DE3), &MDCNFG); - /* Wait for the clock to the SDRAMs to stabilize, 100..200 usec. */ - pxa_wait_ticks(0x300); - - /* - * 8) Trigger a number (usually 8) refresh cycles by attempting - * non-burst read or write accesses to disabled SDRAM, as commonly - * specified in the power up sequence documented in SDRAM data - * sheets. The address(es) used for this purpose must not be - * cacheable. - */ - for (i = 9; i >= 0; i--) { - writel(i, 0xa0000000); - barrier(); - } - /* - * 9) Write MDCNFG with enable bits asserted (MDCNFG:DEx set to 1). - */ - - tmp = DEFAULT_MDCNFG_VAL & - (MDCNFG_DE0 | MDCNFG_DE1 | MDCNFG_DE2 | MDCNFG_DE3); - tmp |= readl(&MDCNFG); - writelrb(tmp, &MDCNFG); - - /* - * 10) Write MDMRS. - */ - - writelrb(DEFAULT_MDMRS_VAL, &MDMRS); - - /* - * 11) Enable APD - */ - - if (DEFAULT_MDREFR_VAL & MDREFR_APD) { - tmp = readl(&MDREFR); - tmp |= MDREFR_APD; - writelrb(tmp, &MDREFR); - } -} - -void __bare_init __naked barebox_arm_reset_vector(uint32_t r0, uint32_t r1, uint32_t r2) -{ - unsigned long pssr = PSPR; - unsigned long pc = get_pc(); - - arm_cpu_lowlevel_init(); - CKEN |= CKEN_OSTIMER | CKEN_MEMC | CKEN_FFUART; - - /* - * When not running from SDRAM, get it out of self refresh, and/or - * initialize it. - */ - if (!(pc >= 0xa0000000 && pc < 0xb0000000)) - pxa2xx_dram_init(); - - if ((pssr >= 0xa0000000 && pssr < 0xb0000000) || - (pssr >= 0x04000000 && pssr < 0x10000000)) - asm("mov pc, %0" : : "r"(pssr) : ); - - barebox_arm_entry(0xa0000000, SZ_64M, 0); -} diff --git a/arch/arm/boards/mainstone/Makefile b/arch/arm/boards/mainstone/Makefile deleted file mode 100644 index da63d2625f..0000000000 --- a/arch/arm/boards/mainstone/Makefile +++ /dev/null @@ -1,4 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0-only - -obj-y += board.o -lwl-y += lowlevel.o diff --git a/arch/arm/boards/mainstone/board.c b/arch/arm/boards/mainstone/board.c deleted file mode 100644 index 979a4f3609..0000000000 --- a/arch/arm/boards/mainstone/board.c +++ /dev/null @@ -1,118 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-or-later -// SPDX-FileCopyrightText: 2015 Robert Jarzmik <[email protected]> - -#include <common.h> -#include <driver.h> -#include <environment.h> -#include <fs.h> -#include <init.h> -#include <led.h> -#include <gpio.h> -#include <pwm.h> -#include <linux/sizes.h> - -#include <mach/pxa/devices.h> -#include <mach/pxa/mfp-pxa27x.h> -#include <mach/pxa/pxa-regs.h> -#include <mach/pxa/udc_pxa2xx.h> -#include <mach/pxa/mci_pxa2xx.h> - -#include <platform_data/eth-smc91111.h> -#include <asm/armlinux.h> -#include <asm/io.h> -#include <asm/mmu.h> - -#include <asm/mach-types.h> - -static struct smc91c111_pdata smsc91x_pdata = { - .word_aligned_short_writes = true, -}; - -static unsigned long mainstone_pin_config[] = { - GPIO15_nCS_1, /* CS1 - Flash */ - GPIO78_nCS_2, /* CS2 - Baseboard FGPA + SRAM */ - GPIO80_nCS_4, /* CS4 - SMC ethernet */ - - /* Ethernet: static memory VLIO */ - GPIO18_RDY, - - /* PC Card */ - GPIO48_nPOE, - GPIO49_nPWE, - GPIO50_nPIOR, - GPIO51_nPIOW, - GPIO85_nPCE_1, - GPIO54_nPCE_2, - GPIO79_PSKTSEL, - GPIO55_nPREG, - GPIO56_nPWAIT, - GPIO57_nIOIS16, - - /* MMC */ - GPIO32_MMC_CLK, - GPIO112_MMC_CMD, - GPIO92_MMC_DAT_0, - GPIO109_MMC_DAT_1, - GPIO110_MMC_DAT_2, - GPIO111_MMC_DAT_3, - - /* LCD - 16bpp DSTN */ - GPIOxx_LCD_TFT_16BPP, - - /* Backlight */ - GPIO16_PWM0_OUT, - - /* FFUART */ - GPIO34_FFUART_RXD, - GPIO35_FFUART_CTS, - GPIO36_FFUART_DCD, - GPIO37_FFUART_DSR, - GPIO38_FFUART_RI, - GPIO39_FFUART_TXD, - GPIO40_FFUART_DTR, - GPIO41_FFUART_RTS, -}; - -static int mainstone_devices_init(void) -{ - void *nor0_iospace; - - armlinux_set_architecture(MACH_TYPE_MAINSTONE); - - pxa_add_uart((void *)0x40100000, 0); - pxa_add_pwm((void *)0x40b00000, 0); - - nor0_iospace = map_io_sections(0x0, (void *)0xe0000000, SZ_64M); - add_cfi_flash_device(0, (ulong)nor0_iospace, SZ_64M, 0); - add_cfi_flash_device(1, 0x04000000, SZ_64M, 0); - devfs_add_partition("nor0", SZ_2M, SZ_256K, DEVFS_PARTITION_FIXED, - "env0"); - add_generic_device("smc91c111", DEVICE_ID_DYNAMIC, NULL, - 0x10000300, 0xff4000, IORESOURCE_MEM, - &smsc91x_pdata); - return 0; -} - -device_initcall(mainstone_devices_init); - -static int mainstone_coredevice_init(void) -{ - /* - * Put the board in superspeed (520 MHz) to speed-up logo/OS loading. - */ - CCCR = CCCR_A | 0x20290; - - barebox_set_model("Mainstone PXA27x"); - barebox_set_hostname("mainstone"); - pxa2xx_mfp_config(ARRAY_AND_SIZE(mainstone_pin_config)); - return 0; -} -coredevice_initcall(mainstone_coredevice_init); - -static int mainstone_mem_init(void) -{ - arm_add_mem_device("ram0", 0xa0000000, SZ_64M); - add_mem_device("sram0", 0x0a000000, SZ_1M, IORESOURCE_MEM_WRITEABLE); - return 0; -} -mem_initcall(mainstone_mem_init); diff --git a/arch/arm/boards/mainstone/env/boot/nor-ubi b/arch/arm/boards/mainstone/env/boot/nor-ubi deleted file mode 100644 index 533605e86a..0000000000 --- a/arch/arm/boards/mainstone/env/boot/nor-ubi +++ /dev/null @@ -1,5 +0,0 @@ -#!/bin/sh - -global.bootm.image="/dev/nor0.kernel" -#global.bootm.oftree="/env/oftree" -global.linux.bootargs.dyn.root="root=ubi0:linux_root ubi.mtd=nor0.root rootfstype=ubifs" diff --git a/arch/arm/boards/mainstone/env/init/mtdparts-nor b/arch/arm/boards/mainstone/env/init/mtdparts-nor deleted file mode 100644 index b5c4e32411..0000000000 --- a/arch/arm/boards/mainstone/env/init/mtdparts-nor +++ /dev/null @@ -1,6 +0,0 @@ -#!/bin/sh - -mtdparts="2048k@0(nor0.barebox)ro,256k(nor0.barebox-env),256k(nor0.barebox-logo),256k(nor0.barebox-logo2),5120k(nor0.kernel),-(nor0.root)" -kernelname="application-flash" - -mtdparts-add -d nor0 -k ${kernelname} -p ${mtdparts} diff --git a/arch/arm/boards/mainstone/env/nv/linux.bootargs.console b/arch/arm/boards/mainstone/env/nv/linux.bootargs.console deleted file mode 100644 index 476b1fbe49..0000000000 --- a/arch/arm/boards/mainstone/env/nv/linux.bootargs.console +++ /dev/null @@ -1 +0,0 @@ -console=ttyS0,115200 diff --git a/arch/arm/boards/mainstone/lowlevel.c b/arch/arm/boards/mainstone/lowlevel.c deleted file mode 100644 index 29d12f7424..0000000000 --- a/arch/arm/boards/mainstone/lowlevel.c +++ /dev/null @@ -1,266 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-only - -#include <common.h> -#include <init.h> -#include <io.h> - -#include <asm/barebox-arm-head.h> -#include <asm/barebox-arm.h> -#include <linux/sizes.h> -#include <mach/pxa/pxa-regs.h> -#include <mach/pxa/regs-ost.h> - -/* - * Memory settings - */ -#define DEFAULT_MSC0_VAL 0x23F2B8F2 -#define DEFAULT_MSC1_VAL 0x7ff0fff1 -/* - * MSC2: static partitions 4 and 5 - * - * [31] 0 - RBUFF5 - * [30:28] 111 - RRR5 - * [27:24] 1111- RDN5 - * [23:20] 1111- RDF5 - * [19] 0 - RBW5 - * [18:16] 000 - RT5 - * [15] 0 - RBUFF4: Slow device (don't wait for data return) - * [14:12] 111 - RRR4: Toff=(2*RRR + 1)*CLK_MEM (from nCS=1 to next nCS=0) - * [11:8] 1111- RDN4: T=2*RDN*CLK_MEM (from nOE=1 to addr hold) - * [7:4] 1111- RDF4: T=RDF*CLK_MEM of hold nOE/nPWE for read/write - * [3] 0 - RBW4: Bus width is 32 bits - * [2:0] 000 - RT4: Partition is VLIO - */ -#define DEFAULT_MSC2_VAL 0x7ff0fff4 - -/* - * MDCNFG: SDRAM Configuration Register - * - * [31] 0 - Memory map 0/1 uses normal 256 MBytes - * [30] 0 - dcacx2: no extra column addressing - * [29] 0 - reserved - * [28] 0 - SA1111 compatiblity mode - * [27] 0 - latch return data with return clock - * [26] 0 - alternate addressing for pair 2/3 - * [25:24] 00 - timings - * [23] 0 - internal banks in lower partition 2/3 (not used) - * [22:21] 00 - row address bits for partition 2/3 (not used) - * [20:19] 00 - column address bits for partition 2/3 (not used) - * [18] 0 - SDRAM partition 2/3 width is 32 bit - * [17] 0 - SDRAM partition 3 disabled - * [16] 0 - SDRAM partition 2 disabled - * [15] 0 - Stack1 : see stack0 - * [14] 0 - dcacx0 : no extra column addressing - * [13] 0 - stack0 : stack = 0b00 => SDRAM address placed on MA<24:10> - * [12] 0 - SA1110 compatiblity mode - * [11] 1 - always 1 - * [10] 0 - no alternate addressing for pair 0/1 - * [09:08] 10 - tRP=2*MemClk CL=2 tRCD=2*MemClk tRAS=7*MemClk tRC=11*MemClk - * [7] 1 - 4 internal banks in partitions 0/1 - * [06:05] 10 - drac0: 13 row address bits for partition 0/1 - * [04:03] 01 - dcac0: 9 column address bits for partition 0/1 - * [02] 0 - SDRAM partition 0/1 width is 32 bit - * [01] 1 - enable SDRAM partition 1 - * [00] 1 - enable SDRAM partition 0 - * - * Configuration is for 1 bank of 64MBytes (13 rows * 9 cols) - * in bank0, of width 32 bits, with 4 internal banks. - * Timings (in times of SDCLK<1>): tRP = 3clk, CL=3, rRCD=3clk, - * tRAS=7clk, tRC=11clk - */ -#define DEFAULT_MDCNFG_VAL 0x00000acb - -/* - * MDREFR: SDRAM Configuration Register - * - * [25] 0 - K2FREE=0 - * [24] 0 - K1FREE=0 - * [23] 0 - K0FREE=0 - * [22] 0 - SLFRSH=0 - * [21] - * [20] 0 - APD - * [19] 0 - K2DB2=0 - * [18] 0 - K2RUN=0 - * [17] 1 - K1DB2=1 - * [16] 1 - K1RUN=1 - * [15] 0 - EP1IN - * [14] 1 - K0DB2=1 - * [13] 1 - K0RUN=1 - * [12] - * [11..0] 17 - DRI=17 - */ -#define DEFAULT_MDREFR_VAL 0x00036017 -#define DEFAULT_MDMRS_VAL 0x00320032 - -#define DEFAULT_FLYCNFG_VAL 0x00000000 -#define DEFAULT_SXCNFG_VAL 0x40044004 - -/* - * PCMCIA and CF Interfaces - */ -#define DEFAULT_MECR_VAL 0x00000001 -#define DEFAULT_MCMEM0_VAL 0x00014307 -#define DEFAULT_MCMEM1_VAL 0x00014307 -#define DEFAULT_MCATT0_VAL 0x0001c787 -#define DEFAULT_MCATT1_VAL 0x0001c787 -#define DEFAULT_MCIO0_VAL 0x0001430f -#define DEFAULT_MCIO1_VAL 0x0001430f - -static inline void writelrb(uint32_t val, volatile u32 __iomem *addr) -{ - writel(val, addr); - barrier(); - readl(addr); - barrier(); -} - -static inline void pxa_wait_ticks(int ticks) -{ - writel(0, &OSCR); - while (readl(&OSCR) < ticks) - barrier(); -} - -static inline void pxa2xx_dram_init(void) -{ - uint32_t tmp, mask; - int i; - /* - * 1) Initialize Asynchronous static memory controller - */ - - writelrb(DEFAULT_MSC1_VAL, &MSC1); - writelrb(DEFAULT_MSC2_VAL, &MSC2); - /* - * 2) Initialize Card Interface - */ - - /* MECR: Memory Expansion Card Register */ - writelrb(DEFAULT_MECR_VAL, &MECR); - /* MCMEM0: Card Interface slot 0 timing */ - writelrb(DEFAULT_MCMEM0_VAL, &MCMEM0); - /* MCMEM1: Card Interface slot 1 timing */ - writelrb(DEFAULT_MCMEM1_VAL, &MCMEM1); - /* MCATT0: Card Interface Attribute Space Timing, slot 0 */ - writelrb(DEFAULT_MCATT0_VAL, &MCATT0); - /* MCATT1: Card Interface Attribute Space Timing, slot 1 */ - writelrb(DEFAULT_MCATT1_VAL, &MCATT1); - /* MCIO0: Card Interface I/O Space Timing, slot 0 */ - writelrb(DEFAULT_MCIO0_VAL, &MCIO0); - /* MCIO1: Card Interface I/O Space Timing, slot 1 */ - writelrb(DEFAULT_MCIO1_VAL, &MCIO1); - - /* - * 3) Configure Fly-By DMA register - */ - - writelrb(DEFAULT_FLYCNFG_VAL, &FLYCNFG); - - /* - * 4) Initialize Timing for Sync Memory (SDCLK0) - */ - - /* - * Before accessing MDREFR we need a valid DRI field, so we set - * this to power on defaults + DRI field. - */ - - /* Read current MDREFR config and zero out DRI */ - tmp = readl(&MDREFR) & ~0xfff; - tmp |= DEFAULT_MDREFR_VAL & 0xfff; - writelrb(tmp, &MDREFR); - - /* clear the free-running clock bits (clear K0Free, K1Free, K2Free) */ - mask = MDREFR_K0FREE | MDREFR_K1FREE | MDREFR_K2FREE | - MDREFR_K0DB2 | MDREFR_K0DB4 | MDREFR_K1DB2 | MDREFR_K2DB2 | - MDREFR_K0RUN | MDREFR_K1RUN | MDREFR_K2RUN; - tmp &= ~mask; - tmp |= (DEFAULT_MDREFR_VAL & mask); - writelrb(tmp, &MDREFR); - - /* - * 5) Initialize Synchronous Static Memory (Flash/Peripherals) - */ - - /* Initialize SXCNFG register. Assert the enable bits. - * - * Write SXMRS to cause an MRS command to all enabled banks of - * synchronous static memory. Note that SXLCR need not be written - * at this time. - */ - writelrb(DEFAULT_SXCNFG_VAL, &SXCNFG); - - /* - * 6) Initialize SDRAM - */ - - tmp &= ~MDREFR_SLFRSH; - writelrb(tmp, &MDREFR); - tmp |= MDREFR_E1PIN; - writelrb(tmp, &MDREFR); - - /* - * 7) Write MDCNFG with MDCNFG:DEx deasserted (set to 0), to configure - * but not enable each SDRAM partition pair. - */ - - mask = MDCNFG_DE0 | MDCNFG_DE1 | MDCNFG_DE2 | MDCNFG_DE3; - writelrb(DEFAULT_MDCNFG_VAL & ~mask, &MDCNFG); - - /* Wait for the clock to the SDRAMs to stabilize, 100..200 usec. */ - pxa_wait_ticks(0x300); - - /* - * 8) Trigger a number (usually 8) refresh cycles by attempting - * non-burst read or write accesses to disabled SDRAM, as commonly - * specified in the power up sequence documented in SDRAM data - * sheets. The address(es) used for this purpose must not be - * cacheable. - */ - for (i = 9; i >= 0; i--) { - readl(0xa0000000); - barrier(); - } - /* - * 9) Write MDCNFG with enable bits asserted (MDCNFG:DEx set to 1). - */ - - tmp = (readl(&MDCNFG) & ~mask) | (DEFAULT_MDCNFG_VAL & mask); - writelrb(tmp, &MDCNFG); - - /* - * 10) Write MDMRS. - */ - writelrb(DEFAULT_MDMRS_VAL, &MDMRS); - - /* - * 11) Enable APD - */ - if (DEFAULT_MDREFR_VAL & MDREFR_APD) { - tmp = readl(&MDREFR); - tmp |= MDREFR_APD; - writelrb(tmp, &MDREFR); - } -} - -void __bare_init __naked barebox_arm_reset_vector(uint32_t r0, uint32_t r1, uint32_t r2) -{ - unsigned long pssr = PSPR; - unsigned long pc = get_pc(); - - arm_cpu_lowlevel_init(); - CKEN |= CKEN_OSTIMER | CKEN_MEMC | CKEN_FFUART; - - /* - * When not running from SDRAM, get it out of self refresh, and/or - * initialize it. - */ - if (!(pc >= 0xa0000000 && pc < 0xb0000000)) - pxa2xx_dram_init(); - - if ((pssr >= 0xa0000000 && pssr < 0xb0000000) || - (pssr >= 0x04000000 && pssr < 0x10000000)) - asm("mov pc, %0" : : "r"(pssr) : ); - - barebox_arm_entry(0xa0000000, SZ_64M, 0); -} diff --git a/arch/arm/boards/mioa701/Makefile b/arch/arm/boards/mioa701/Makefile deleted file mode 100644 index bf17869fb2..0000000000 --- a/arch/arm/boards/mioa701/Makefile +++ /dev/null @@ -1,4 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0-only - -obj-y += board.o gpio0_poweroff.o -lwl-y += lowlevel.o diff --git a/arch/arm/boards/mioa701/board.c b/arch/arm/boards/mioa701/board.c deleted file mode 100644 index 685c78611b..0000000000 --- a/arch/arm/boards/mioa701/board.c +++ /dev/null @@ -1,274 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-or-later -// SPDX-FileCopyrightText: 2011 Robert Jarzmik <[email protected]> - -#include <common.h> -#include <driver.h> -#include <environment.h> -#include <fs.h> -#include <init.h> -#include <led.h> -#include <gpio.h> -#include <pwm.h> - -#include <mach/pxa/devices.h> -#include <mach/pxa/mfp-pxa27x.h> -#include <mach/pxa/pxa-regs.h> -#include <mach/pxa/udc_pxa2xx.h> -#include <mach/pxa/mci_pxa2xx.h> - -#include <asm/armlinux.h> -#include <asm/io.h> -#include <asm/mach-types.h> -#include <asm/mmu.h> - -#include "mioa701.h" - -/* - * LTM0305A776C LCD panel timings - * - * see: - * - the LTM0305A776C datasheet, - * - and the PXA27x Programmers' manual - */ -static struct pxafb_videomode mioa701_ltm0305a776c = { - { - .pixclock = 220000, /* CLK=4.545 MHz */ - .xres = 240, - .yres = 320, - .hsync_len = 4, - .vsync_len = 2, - .left_margin = 6, - .right_margin = 4, - .upper_margin = 5, - .lower_margin = 3, - }, - .bpp = 16, -}; - -static void mioa701_lcd_power(int on) -{ - gpio_set_value(GPIO87_LCD_POWER, on); -} - -static void mioa701_lcd_backlight(int on) -{ - struct pwm_device *pwm0 = pwm_request("pwm0"); - - /* - * The backlight has a base frequency of 250kHz (<=> 4 ms). - */ - if (on) { - pwm_enable(pwm0); - pwm_config(pwm0, 2000 * 1024, 4000 * 1024); - } else { - pwm_disable(pwm0); - } - pwm_free(pwm0); -} - -static struct pxafb_platform_data mioa701_pxafb_info = { - .mode = &mioa701_ltm0305a776c, - .lcd_conn = LCD_COLOR_TFT_16BPP | LCD_PCLK_EDGE_FALL, - .lcd_power = mioa701_lcd_power, - .backlight_power = mioa701_lcd_backlight, -}; - -#define MIO_LED(_name, _gpio) \ - { .gpio = _gpio, .active_low = 1, .led = { .name = #_name, } } -static struct gpio_led leds[] = { - MIO_LED(charging, GPIO10_LED_nCharging), - MIO_LED(blue, GPIO97_LED_nBlue), - MIO_LED(orange, GPIO98_LED_nOrange), - MIO_LED(vibra, GPIO82_LED_nVibra), - MIO_LED(keyboard, GPIO115_LED_nKeyboard), -}; - - -static int is_usb_connected(void) -{ - return !gpio_get_value(GPIO13_nUSB_DETECT); -} - -static struct pxa2xx_udc_mach_info mioa701_udc_info = { - .udc_is_connected = is_usb_connected, - .gpio_pullup = GPIO22_USB_ENABLE, -}; - -static struct pxamci_platform_data mioa701_mmc_info = { - .gpio_power = GPIO91_SDIO_EN, -}; - -static int mioa701_devices_init(void) -{ - int i; - void *docg3_iospace; - - pxa_add_pwm((void *)0x40b00000, 0); - pxa_add_fb((void *)0x44000000, &mioa701_pxafb_info); - pxa_add_mmc((void *)0x41100000, DEVICE_ID_DYNAMIC, &mioa701_mmc_info); - docg3_iospace = map_io_sections(0x0, (void *)0xe0000000, 0x2000); - add_generic_device("docg3", DEVICE_ID_DYNAMIC, NULL, (ulong) docg3_iospace, - 0x2000, IORESOURCE_MEM, NULL); - armlinux_set_architecture(MACH_TYPE_MIOA701); - - for (i = 0; i < ARRAY_SIZE(leds); i++) - led_gpio_register(&leds[i]); - add_generic_device("pxa27x-udc", 0, NULL, 0x40600000, - 1024, IORESOURCE_MEM, &mioa701_udc_info); - return 0; -} - -device_initcall(mioa701_devices_init); - -static unsigned long mioa701_pin_config[] = { - /* Mio global */ - MIO_CFG_OUT(GPIO9_CHARGE_EN, AF0, DRIVE_LOW), - MIO_CFG_OUT(GPIO18_POWEROFF, AF0, DRIVE_LOW), - MFP_CFG_OUT(GPIO3, AF0, DRIVE_HIGH), - MFP_CFG_OUT(GPIO4, AF0, DRIVE_HIGH), - MIO_CFG_IN(GPIO80_MAYBE_CHARGE_VDROP, AF0), - - /* Backlight PWM 0 */ - GPIO16_PWM0_OUT, - - /* LCD */ - GPIOxx_LCD_TFT_16BPP, - MIO_CFG_OUT(GPIO87_LCD_POWER, AF0, DRIVE_LOW), - - /* MMC */ - GPIO32_MMC_CLK, - GPIO92_MMC_DAT_0, - GPIO109_MMC_DAT_1, - GPIO110_MMC_DAT_2, - GPIO111_MMC_DAT_3, - GPIO112_MMC_CMD, - MIO_CFG_IN(GPIO78_SDIO_RO, AF0), - MIO_CFG_IN(GPIO15_SDIO_INSERT, AF0), - MIO_CFG_OUT(GPIO91_SDIO_EN, AF0, DRIVE_LOW), - - /* USB */ - MIO_CFG_IN(GPIO13_nUSB_DETECT, AF0), - MIO_CFG_OUT(GPIO22_USB_ENABLE, AF0, DRIVE_LOW), - - /* QCI */ - GPIO12_CIF_DD_7, - GPIO17_CIF_DD_6, - GPIO50_CIF_DD_3, - GPIO51_CIF_DD_2, - GPIO52_CIF_DD_4, - GPIO53_CIF_MCLK, - GPIO54_CIF_PCLK, - GPIO55_CIF_DD_1, - GPIO81_CIF_DD_0, - GPIO82_CIF_DD_5, - GPIO84_CIF_FV, - GPIO85_CIF_LV, - - /* Bluetooth */ - MIO_CFG_IN(GPIO14_BT_nACTIVITY, AF0), - GPIO44_BTUART_CTS, - GPIO42_BTUART_RXD, - GPIO45_BTUART_RTS, - GPIO43_BTUART_TXD, - MIO_CFG_OUT(GPIO83_BT_ON, AF0, DRIVE_LOW), - MIO_CFG_OUT(GPIO77_BT_UNKNOWN1, AF0, DRIVE_HIGH), - MIO_CFG_OUT(GPIO86_BT_MAYBE_nRESET, AF0, DRIVE_HIGH), - - /* GPS */ - MIO_CFG_OUT(GPIO23_GPS_UNKNOWN1, AF0, DRIVE_LOW), - MIO_CFG_OUT(GPIO26_GPS_ON, AF0, DRIVE_LOW), - MIO_CFG_OUT(GPIO27_GPS_RESET, AF0, DRIVE_LOW), - MIO_CFG_OUT(GPIO106_GPS_UNKNOWN2, AF0, DRIVE_LOW), - MIO_CFG_OUT(GPIO107_GPS_UNKNOWN3, AF0, DRIVE_LOW), - GPIO46_STUART_RXD, - GPIO47_STUART_TXD, - - /* GSM */ - MIO_CFG_OUT(GPIO24_GSM_MOD_RESET_CMD, AF0, DRIVE_LOW), - MIO_CFG_OUT(GPIO88_GSM_nMOD_ON_CMD, AF0, DRIVE_HIGH), - MIO_CFG_OUT(GPIO90_GSM_nMOD_OFF_CMD, AF0, DRIVE_HIGH), - MIO_CFG_OUT(GPIO114_GSM_nMOD_DTE_UART_STATE, AF0, DRIVE_HIGH), - MIO_CFG_IN(GPIO25_GSM_MOD_ON_STATE, AF0), - MIO_CFG_IN(GPIO113_GSM_EVENT, AF0) | WAKEUP_ON_EDGE_BOTH, - GPIO34_FFUART_RXD, - GPIO35_FFUART_CTS, - GPIO36_FFUART_DCD, - GPIO37_FFUART_DSR, - GPIO39_FFUART_TXD, - GPIO40_FFUART_DTR, - GPIO41_FFUART_RTS, - - /* Sound */ - GPIO28_AC97_BITCLK, - GPIO29_AC97_SDATA_IN_0, - GPIO30_AC97_SDATA_OUT, - GPIO31_AC97_SYNC, - GPIO89_AC97_SYSCLK, - MIO_CFG_IN(GPIO12_HPJACK_INSERT, AF0), - - /* Leds */ - MIO_CFG_OUT(GPIO10_LED_nCharging, AF0, DRIVE_HIGH), - MIO_CFG_OUT(GPIO97_LED_nBlue, AF0, DRIVE_HIGH), - MIO_CFG_OUT(GPIO98_LED_nOrange, AF0, DRIVE_HIGH), - MIO_CFG_OUT(GPIO82_LED_nVibra, AF0, DRIVE_HIGH), - MIO_CFG_OUT(GPIO115_LED_nKeyboard, AF0, DRIVE_HIGH), - - /* Keyboard */ - MIO_CFG_IN(GPIO0_KEY_POWER, AF0) | WAKEUP_ON_EDGE_BOTH, - MIO_CFG_IN(GPIO93_KEY_VOLUME_UP, AF0), - MIO_CFG_IN(GPIO94_KEY_VOLUME_DOWN, AF0), - GPIO100_KP_MKIN_0, - GPIO101_KP_MKIN_1, - GPIO102_KP_MKIN_2, - GPIO103_KP_MKOUT_0, - GPIO104_KP_MKOUT_1, - GPIO105_KP_MKOUT_2, - - /* I2C */ - GPIO117_I2C_SCL, - GPIO118_I2C_SDA, - - /* Unknown */ - MFP_CFG_IN(GPIO20, AF0), - MFP_CFG_IN(GPIO21, AF0), - MFP_CFG_IN(GPIO33, AF0), - MFP_CFG_OUT(GPIO49, AF0, DRIVE_HIGH), - MFP_CFG_OUT(GPIO57, AF0, DRIVE_HIGH), - MFP_CFG_IN(GPIO96, AF0), - MFP_CFG_OUT(GPIO116, AF0, DRIVE_HIGH), -}; - -static int mioa701_coredevice_init(void) -{ - unsigned int cclk; - /* route pins */ - pxa2xx_mfp_config(ARRAY_AND_SIZE(mioa701_pin_config)); - - /* - * Put the board in superspeed (520 MHz) to speed-up logo/OS loading. - * This requires to command the Maxim 1586 to upgrade core voltage to - * 1.475 V, on the power I2C bus (device 0x14). - */ - CKEN |= CKEN_PWRI2C; - CCCR = CCCR_A | 0x20290; - PCFR = PCFR_GPR_EN | PCFR_FVC | PCFR_DC_EN | PCFR_PI2C_EN | PCFR_OPDE; - PCMD(0) = PCMD_LC | 0x1f; - PVCR = 0x14; - - cclk = 0x0b; - asm volatile("mcr p14, 0, %0, c6, c0, 0 @ set CCLK" - : : "r" (cclk) : "cc"); - - barebox_set_model("Scoter Mitac Mio A701"); - barebox_set_hostname("mioa701"); - - return 0; -} -coredevice_initcall(mioa701_coredevice_init); - -static int mioa701_mem_init(void) -{ - arm_add_mem_device("ram0", 0xa0000000, 64 * 1024 * 1024); - return 0; -} -mem_initcall(mioa701_mem_init); diff --git a/arch/arm/boards/mioa701/env/bin/barebox_update b/arch/arm/boards/mioa701/env/bin/barebox_update deleted file mode 100644 index 632c20926a..0000000000 --- a/arch/arm/boards/mioa701/env/bin/barebox_update +++ /dev/null @@ -1,11 +0,0 @@ -#!/bin/sh - -# Page+OOB specific partitions -addpart /dev/mtd0.raw 2162688@405504(barebox) - -if [ -r /barebox.BIP0 ]; then - dps1_unlock - erase /dev/mtd0.raw.barebox - cp -v /barebox.BIPO /dev/mtd0.raw.barebox - dps1_unlock -fi diff --git a/arch/arm/boards/mioa701/env/bin/console_mode b/arch/arm/boards/mioa701/env/bin/console_mode deleted file mode 100644 index aa06e920b4..0000000000 --- a/arch/arm/boards/mioa701/env/bin/console_mode +++ /dev/null @@ -1,6 +0,0 @@ -#!/bin/sh -# Script to run barebox in console mode - -splash /dev/mtd0.barebox-logo2 -echo -echo "Welcome to barebox console" diff --git a/arch/arm/boards/mioa701/env/bin/dps1_unlock b/arch/arm/boards/mioa701/env/bin/dps1_unlock deleted file mode 100644 index 2d7dab8c58..0000000000 --- a/arch/arm/boards/mioa701/env/bin/dps1_unlock +++ /dev/null @@ -1,12 +0,0 @@ -#!/bin/sh -# -# Shell to unlock the DPS1 with "12345678" key. - -mw -b 0x105e 0x31 -mw -b 0x105e 0x32 -mw -b 0x105e 0x33 -mw -b 0x105e 0x34 -mw -b 0x105e 0x35 -mw -b 0x105e 0x36 -mw -b 0x105e 0x37 -mw -b 0x105e 0x38 diff --git a/arch/arm/boards/mioa701/env/bin/dps1_update b/arch/arm/boards/mioa701/env/bin/dps1_update deleted file mode 100644 index e6535eda72..0000000000 --- a/arch/arm/boards/mioa701/env/bin/dps1_update +++ /dev/null @@ -1,12 +0,0 @@ -#!/bin/sh - -# Page+OOB specific partitions -addpart /dev/mtd0.raw 67584@202752(dps1) -uncompress /env/data/dps1.raw.gz /dps1.raw - -if [ -r /dps1.raw ]; then - dps1_unlock - erase /dev/mtd0.raw.dps1 - cp -v /dps1.raw /dev/mtd0.raw.dps1 - dps1_unlock -fi diff --git a/arch/arm/boards/mioa701/env/bin/init b/arch/arm/boards/mioa701/env/bin/init deleted file mode 100644 index e914eae32f..0000000000 --- a/arch/arm/boards/mioa701/env/bin/init +++ /dev/null @@ -1,79 +0,0 @@ -#!/bin/sh - -PATH=/env/bin -export PATH - -. /env/config -addpart /dev/mtd0 $mtdparts - -usbserial -s "Mio A701 usb gadget" - -gpio_get_value 22 -is_usb_connected=$? - -gpio_get_value 93 -is_vol_up=$? - -fb0.enable=1 -# Phase1: Handle Vol-Up key case : drop immediately to console -if [ $is_vol_up != 0 ]; then - console_mode - exit -fi - -# Phase2: Handle Power-On case : debounce PowerUp key or Halt -if [ $global.system.reset = "POR" -o $global.system.reset = "WKE" ]; then - powerup_released=0 - - gpio_get_value 0 - is_power_up=$? - if [ $is_power_up = 0 ]; then - powerup_released=1 - fi - msleep 500 - - gpio_get_value 0 - is_power_up=$? - if [ $is_power_up = 0 ]; then - powerup_released=1 - fi - - if [ $powerup_released = 1 ]; then - echo "Power button not held, halting" - poweroff - fi -fi - -# Phase3: display logo -led keyboard 0 -splash /dev/mtd0.barebox-logo - -# Phase4: check for SD Card override -sdcard_override -if [ $? = 0 ]; then - console_mode - exit -fi - -# Phase5: check for MTD override -mtd_env_override -if [ $? = 0 ]; then - echo "Switching to custom environment" - /env/init - exit -fi - -# Phase6: check for user interrupting auto-boot -echo "No custom environment found" -if [ $is_usb_connected != 0 ]; then - echo -n "Hit any key to stop autoboot: " - timeout -a $autoboot_timeout - if [ $? != 0 ]; then - console_mode - exit - fi -fi - -# Phase7: auto-boot linux kernel -echo "Booting linux kernel on docg3 chip ..." -bootm /dev/mtd0.kernel diff --git a/arch/arm/boards/mioa701/env/bin/mtd_env_override b/arch/arm/boards/mioa701/env/bin/mtd_env_override deleted file mode 100644 index faeb4d0d43..0000000000 --- a/arch/arm/boards/mioa701/env/bin/mtd_env_override +++ /dev/null @@ -1,4 +0,0 @@ -#!/bin/sh - -loadenv /dev/mtd0.barebox-env -exit $? diff --git a/arch/arm/boards/mioa701/env/bin/sdcard_override b/arch/arm/boards/mioa701/env/bin/sdcard_override deleted file mode 100644 index 7003fa967e..0000000000 --- a/arch/arm/boards/mioa701/env/bin/sdcard_override +++ /dev/null @@ -1,19 +0,0 @@ -#!/bin/sh -# Script to switch to execute sdcard environment scripts if available -# -# This enables an override of the default environment if an SD Card -# is inserted, has a FAT filesystem, and has a barebox.env file in -# the root directory. - -mci0.probe=1 -if [ $mci0.probe = 1 ]; then - mkdir /sdcard - mount /dev/disk0.0 /sdcard - if [ -f /sdcard/barebox.env ]; then - loadenv /sdcard/barebox.env /env.sd - /env.sd/bin/init - exit - fi -fi -trigger_error_return_code -exit diff --git a/arch/arm/boards/mioa701/env/config b/arch/arm/boards/mioa701/env/config deleted file mode 100644 index 92014511b4..0000000000 --- a/arch/arm/boards/mioa701/env/config +++ /dev/null @@ -1,6 +0,0 @@ -#!/bin/sh - -autoboot_timeout=3 - -mtdparts="2048k@384k(barebox)ro,256k(barebox-logo),256k(barebox-logo2),128k(barebox-env),5120k(kernel),-(root)" -bootargs="$bootargs mtdparts=docg3.0:$mtdparts ubi.mtd=5 rootfstype=ubifs root=ubi0:linux_root ro" diff --git a/arch/arm/boards/mioa701/env/data/dps1.raw.gz b/arch/arm/boards/mioa701/env/data/dps1.raw.gz deleted file mode 100644 index 9857c83e0718d0268dd8c2082193063cd3dfbc72..0000000000000000000000000000000000000000 GIT binary patch literal 0 HcmV?d00001 literal 1324 zcmV+{1=IQ;iwFo+Y|>Hy17vV>F)ngpcL42GacEUl82`?__vvdcy>1KV9D1A!%r?54 zujjVx?YVHIDc)LT!~!*=OvAMd!UEskb4xU8If)^`PMCj1U=)Nx@$8LJ{t?;=B>dyu zd$_0#WYixLNVng)?@dQE{|fr&{NUp|=eytezH`p^o!>R-L27ATn|L_6uC0cMwyyc{ z^s_hL3^g<~G)&D88X6iJ8vg?Qf6&m-m<yU8H13AeM8EwNhX0hhnK4m}w(i-_H>`77 z_$GG?Z{|<!-}O@e0ls->|H0Sx>_tzVaK?fY_E<n%$XYuWyoYf;^bu$deHglSaW2R} zH)6i3UdYwZ2QY7f?o)Pr-v?dEbAb)pZj5W7cPJaa^+G?5Z_jZx&IN0h3b}(Tzg+MN z^gc)*#Nk<=C3C)o@$&E?kEoa?BZFNUCUGk^kMIgI&G!<0AE(MAY~ZtoFzmeb!O)_Q znHw9Xs<lEgTS%4rtMZxZ5sO3OutocWSTquh;`=Bc3z$tsgAaHrr^QDCcK>%W8rvhm zJNRxa9gtS}yaa7K#{+YH&bMu7deXZUh8-2HLRPI3lCb8k;wU*DFefL;$p($M`!uwr zY{{IoFjnWj+&q1VhTpofgiKB((myY->{e=^IQ-*?VNMILRNn}!qe(PeK6VAe>2%!L z=C8-T*Aw<jyNV`diV3VUFA9$wA)8d))Va_*lpncj=CfBVC+D;Li$$Vd`DYkjP<yc8 zu-Zh#(Cpo9MtOQI73WUwUXHngJ6k|i67F?sZ$?FrWJE`=gyGchkY6BbU*s(ERyYMY ziL;y24|sOx;v4TjT97f=SVvA8u-l#N#ulekx5u$hRfjmF22#&I49w(XzRk0!=|FS_ zbr#FcqNcc$rYvfL{N<V)Lf$8C=f9Ya_CU@CGF<wBXsTA#zC*}!D+^v1pA4qC;m=3x zE?$Ug&}9=f&hlx4&pe#7hL6P<iE7wb7fr^{ordyngTGos<vT*oQ>ri2xZW<sQRg~S zQ}9yAF<aF7MJK~>#z)yqTSR_FzNFhwqg4KUaIWRN*G88DMz#!zeAKH#t%=r_`{Cf; z_9Yuzj*;dE%@3L%G(Tv5(EOnJLGy#=2h9(fA2dJwSNt#&o7W1Dj|*=meweTHL!0?( zz4A#CBoDFg>__>w!k$pJvM77|?Oce1x7G&#KhO_->E`R7xWemnV?Ol^7Fk+&3rW2R zA*WD-9ne*nU&A;?*vqRzURHMWWWt#U(lqF&pq2atdx$s=zNOrWAW^m}Ijh#g&eAph zY`gM%+bLEj(-SeaS;(X_abL<E4?c(g3a5x1<M1m<U*?-@(HSyAR%8l+>J=u0tn3pq zzH=;S$J?;JKp(ougIF&N7iAtkDA7~{a^HhHXyxNU3^hs&j|cN{o)ol_*?Cf#l6;MI z1CXN-;}P^z%Xst_jb-Que#!fi4|(W+f91j+_5SLjx=?BD&ZvK%k;c9ue|bjbqB?Ru z0&l7}+~a`^>nzN}L_sdVoP@w@b>ZJ#HPa8<U(SAdc(j+8yRk~WQ`3q0jC!Qu4jRlI z^baBag)scp=zG_1R6OTA?=weKGup29Ss?g+i+yb?y`@v#-QCo+$=w#3ihKn45_g9_ zuy|4SLsx*u)jU?7pKB?2XPimTsO*s&!f@HCD2~Se1a|V~8`saazpnW~^F!1RnjbV~ iLGy#=2h9%}b3yZi<_FCW8gt<`Kl}}u?I7TQF#rH>#-j-U diff --git a/arch/arm/boards/mioa701/gpio0_poweroff.c b/arch/arm/boards/mioa701/gpio0_poweroff.c deleted file mode 100644 index 41d886d74b..0000000000 --- a/arch/arm/boards/mioa701/gpio0_poweroff.c +++ /dev/null @@ -1,67 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-or-later -// SPDX-FileCopyrightText: 2011 Robert Jarzmik <[email protected]> - -#include <clock.h> -#include <common.h> -#include <init.h> -#include <poweroff.h> -#include <gpio.h> -#include <poller.h> - -#include "mioa701.h" - -#define POWEROFF_SECS (4 * SECOND) - -static void blink_led_keyboard(void) -{ - gpio_set_value(GPIO115_LED_nKeyboard, 0); - mdelay(400); - gpio_set_value(GPIO115_LED_nKeyboard, 1); - mdelay(400); -} - -static void try_poweroff(void) -{ - int poweroff_released = 0; - - blink_led_keyboard(); - poweroff_released |= !gpio_get_value(GPIO0_KEY_POWER); - if (poweroff_released) - return; - - gpio_set_value(GPIO115_LED_nKeyboard, 0); - mdelay(2000); - poweroff_machine(); -} - -static void gpio0_poller_fn(struct poller_struct *poller) -{ - static uint64_t gpio0_start; - static bool gpio0_activated; - - if (!gpio_get_value(GPIO0_KEY_POWER)) { - gpio0_activated = false; - return; - } - - if (gpio0_activated) { - if (is_timeout_non_interruptible(gpio0_start, POWEROFF_SECS)) { - try_poweroff(); - gpio0_activated = false; - } - } else { - gpio0_activated = true; - gpio0_start = get_time_ns(); - } -} - -static struct poller_struct gpio0_poller = { - .func = gpio0_poller_fn, -}; - -static int gpio0_poweroff_probe(void) -{ - return poller_register(&gpio0_poller, "power-button"); -} - -device_initcall(gpio0_poweroff_probe); diff --git a/arch/arm/boards/mioa701/lowlevel.c b/arch/arm/boards/mioa701/lowlevel.c deleted file mode 100644 index 6116990402..0000000000 --- a/arch/arm/boards/mioa701/lowlevel.c +++ /dev/null @@ -1,12 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-only - -#include <common.h> -#include <linux/sizes.h> -#include <asm/barebox-arm-head.h> -#include <asm/barebox-arm.h> - -void __naked barebox_arm_reset_vector(uint32_t r0, uint32_t r1, uint32_t r2) -{ - arm_cpu_lowlevel_init(); - barebox_arm_entry(0xa0000000, SZ_64M, NULL); -} diff --git a/arch/arm/boards/mioa701/mioa701.h b/arch/arm/boards/mioa701/mioa701.h deleted file mode 100644 index 5f6d5e65f7..0000000000 --- a/arch/arm/boards/mioa701/mioa701.h +++ /dev/null @@ -1,67 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-or-later -// SPDX-FileCopyrightText: 2011 Robert Jarzmik <[email protected]> - -#ifndef _MIOA701_H_ -#define _MIOA701_H_ - -#define MIO_CFG_IN(pin, af) \ - ((MFP_CFG_DEFAULT & ~(MFP_AF_MASK | MFP_DIR_MASK)) |\ - (MFP_PIN(pin) | MFP_##af | MFP_DIR_IN)) - -#define MIO_CFG_OUT(pin, af, state) \ - ((MFP_CFG_DEFAULT & ~(MFP_AF_MASK | MFP_DIR_MASK | MFP_LPM_STATE_MASK)) |\ - (MFP_PIN(pin) | MFP_##af | MFP_DIR_OUT | MFP_LPM_##state)) - -/* Global GPIOs */ -#define GPIO9_CHARGE_EN 9 -#define GPIO18_POWEROFF 18 -#define GPIO87_LCD_POWER 87 -#define GPIO96_AC_DETECT 96 -#define GPIO80_MAYBE_CHARGE_VDROP 80 /* Drop of 88mV */ - -/* USB */ -#define GPIO13_nUSB_DETECT 13 -#define GPIO22_USB_ENABLE 22 - -/* SDIO bits */ -#define GPIO78_SDIO_RO 78 -#define GPIO15_SDIO_INSERT 15 -#define GPIO91_SDIO_EN 91 - -/* Bluetooth */ -#define GPIO14_BT_nACTIVITY 14 -#define GPIO83_BT_ON 83 -#define GPIO77_BT_UNKNOWN1 77 -#define GPIO86_BT_MAYBE_nRESET 86 - -/* GPS */ -#define GPIO23_GPS_UNKNOWN1 23 -#define GPIO26_GPS_ON 26 -#define GPIO27_GPS_RESET 27 -#define GPIO106_GPS_UNKNOWN2 106 -#define GPIO107_GPS_UNKNOWN3 107 - -/* GSM */ -#define GPIO24_GSM_MOD_RESET_CMD 24 -#define GPIO88_GSM_nMOD_ON_CMD 88 -#define GPIO90_GSM_nMOD_OFF_CMD 90 -#define GPIO114_GSM_nMOD_DTE_UART_STATE 114 -#define GPIO25_GSM_MOD_ON_STATE 25 -#define GPIO113_GSM_EVENT 113 - -/* SOUND */ -#define GPIO12_HPJACK_INSERT 12 - -/* LEDS */ -#define GPIO10_LED_nCharging 10 -#define GPIO97_LED_nBlue 97 -#define GPIO98_LED_nOrange 98 -#define GPIO82_LED_nVibra 82 -#define GPIO115_LED_nKeyboard 115 - -/* Keyboard */ -#define GPIO0_KEY_POWER 0 -#define GPIO93_KEY_VOLUME_UP 93 -#define GPIO94_KEY_VOLUME_DOWN 94 - -#endif /* _MIOA701_H */ diff --git a/arch/arm/boards/phytec-phycore-pxa270/Makefile b/arch/arm/boards/phytec-phycore-pxa270/Makefile deleted file mode 100644 index e00d1cfd7f..0000000000 --- a/arch/arm/boards/phytec-phycore-pxa270/Makefile +++ /dev/null @@ -1,4 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0-only - -obj-y += board.o -lwl-y += lowlevel_init.o diff --git a/arch/arm/boards/phytec-phycore-pxa270/board.c b/arch/arm/boards/phytec-phycore-pxa270/board.c deleted file mode 100644 index 0283659a4e..0000000000 --- a/arch/arm/boards/phytec-phycore-pxa270/board.c +++ /dev/null @@ -1,171 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-or-later -// SPDX-FileCopyrightText: 2009 Sascha Hauer <[email protected]>, Pengutronix -// SPDX-FileCopyrightText: 2010 Marc Kleine-Budde <[email protected]> - -#include <common.h> -#include <driver.h> -#include <environment.h> -#include <fs.h> -#include <init.h> -#include <linux/sizes.h> - -#include <gpio.h> -#include <mach/pxa/mfp-pxa27x.h> -#include <mach/pxa/pxa-regs.h> -#include <mach/pxa/pxafb.h> -#include <mach/pxa/devices.h> - -#include <asm/armlinux.h> -#include <asm/io.h> -#include <asm/mach-types.h> -#include <asm/mmu.h> - -#define PCM990_CTRL_PHYS (void *)PXA_CS1_PHYS - -#define PCM990_CTRL_REG3 0x0006 /* LCD CTRL REGISTER 3 */ -#define PCM990_CTRL_LCDPWR 0x0001 /* RW LCD Power on */ -#define PCM990_CTRL_LCDON 0x0002 /* RW LCD Latch on */ -#define PCM990_CTRL_LCDPOS1 0x0004 /* RW POS 1 */ -#define PCM990_CTRL_LCDPOS2 0x0008 /* RW POS 2 */ - -static void lcd_power(int on) -{ - void __iomem *ctrl3 = PCM990_CTRL_PHYS + PCM990_CTRL_REG3; - - if (on) - writeb(PCM990_CTRL_LCDPWR | PCM990_CTRL_LCDON, ctrl3); - else - writeb(0x0, ctrl3); -} - -static void backlight_power(int on) -{ - if (on) { - mdelay(20); - gpio_set_value(16, 1); - } else { - gpio_set_value(16, 0); - } -} - -static struct pxafb_videomode pxafb_mode = { - .mode = { - .pixclock = 28000, - .xres = 640, - .yres = 480, - .hsync_len = 20, - .left_margin = 103, - .right_margin = 47, - .vsync_len = 6, - .upper_margin = 28, - .lower_margin = 5, - .sync = 0, - }, - .bpp = 16, -}; - -static struct pxafb_platform_data fb_pdata = { - .mode = &pxafb_mode, - .lcd_conn = LCD_COLOR_TFT_16BPP | LCD_PCLK_EDGE_FALL, - .lcd_power = lcd_power, - .backlight_power = backlight_power, -}; - -static int pcm027_mem_init(void) -{ - arm_add_mem_device("ram0", 0xa0000000, SZ_64M); - - return 0; -} -mem_initcall(pcm027_mem_init); - -static unsigned long pin_config[] = { - /* Chip Selects */ - GPIO20_nSDCS_2, - GPIO21_nSDCS_3, - GPIO15_nCS_1, - GPIO78_nCS_2, - GPIO80_nCS_4, - - /* Variable Latency I/O Ready Pin */ - GPIO18_RDY, - - /* FFUART */ - GPIO85_nPCE_1, /* enables RX */ - GPIO34_FFUART_RXD, - GPIO35_FFUART_CTS, - GPIO36_FFUART_DCD, - GPIO37_FFUART_DSR, - GPIO38_FFUART_RI, - GPIO39_FFUART_TXD, - GPIO40_FFUART_DTR, - GPIO41_FFUART_RTS, - - /* LCD */ - GPIO58_LCD_LDD_0, - GPIO59_LCD_LDD_1, - GPIO60_LCD_LDD_2, - GPIO61_LCD_LDD_3, - GPIO62_LCD_LDD_4, - GPIO63_LCD_LDD_5, - GPIO64_LCD_LDD_6, - GPIO65_LCD_LDD_7, - GPIO66_LCD_LDD_8, - GPIO67_LCD_LDD_9, - GPIO68_LCD_LDD_10, - GPIO69_LCD_LDD_11, - GPIO70_LCD_LDD_12, - GPIO71_LCD_LDD_13, - GPIO72_LCD_LDD_14, - GPIO73_LCD_LDD_15, - GPIO74_LCD_FCLK, - GPIO75_LCD_LCLK, - GPIO76_LCD_PCLK, - GPIO77_LCD_BIAS, - MFP_CFG_OUT(GPIO16, AF0, DRIVE_LOW), /* backlight */ - - /* NIC */ - GPIO33_nCS_5, - GPIO49_nPWE, -}; - -static int pcm027_devices_init(void) -{ - void *cfi_iospace; - - add_generic_device("smc91c111", DEVICE_ID_DYNAMIC, NULL, 0x14000300, 16, - IORESOURCE_MEM, NULL); - - cfi_iospace = map_io_sections(0x0, (void *)0xe0000000, SZ_32M); - add_cfi_flash_device(DEVICE_ID_DYNAMIC, (unsigned long)cfi_iospace, SZ_32M, 0); - - pxa_add_fb((void *)0x44000000, &fb_pdata); - - armlinux_set_architecture(MACH_TYPE_PCM027); - - devfs_add_partition("nor0", 0x00000, SZ_512K, DEVFS_PARTITION_FIXED, "self0"); - devfs_add_partition("nor0", SZ_512K, SZ_256K, DEVFS_PARTITION_FIXED, "env0"); - protect_file("/dev/env0", 1); - - return 0; -} - -device_initcall(pcm027_devices_init); - -static int pcm027_console_init(void) -{ - /* route pins */ - pxa2xx_mfp_config(ARRAY_AND_SIZE(pin_config)); - - /* enable clock */ - CKEN |= CKEN_FFUART; - - barebox_set_model("Phytec phyCORE-PXA270"); - barebox_set_hostname("pcm027"); - - pxa_add_uart((void *)0x40100000, 0); - - return 0; -} - -console_initcall(pcm027_console_init); diff --git a/arch/arm/boards/phytec-phycore-pxa270/config.h b/arch/arm/boards/phytec-phycore-pxa270/config.h deleted file mode 100644 index 6aba53edea..0000000000 --- a/arch/arm/boards/phytec-phycore-pxa270/config.h +++ /dev/null @@ -1,314 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0-or-later */ - -/* - * Copyright (C) 2005 Phytec Messtechnik GmbH - * Juergen Kilb, H. Klaholz <[email protected]> - * - * Copyright (C) 2006 Pengutronix - * Sascha Hauer <[email protected]> - * Robert Schwebel <[email protected]> - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * phyCORE-PXA270 configuration settings - * Set these to 0/1 to enable or disable the features. - */ - -#define PHYCORE_PXA270_USE_K3FLASH 0 - -/* 260 MHz or 520 MHZ */ -#define PHYCORE_PXA270_SPEED 520 - -/********************************************************************* - * CONFIG PXA270 GPIO settings * - *********************************************************************/ - -/* - * GPIO set "1" - * - *** REG GPSR0 - * GP15 == nCS1 is 1 - * GP20 == nSDCS2 is 1 - * GP21 == nSDCS3 is 1 - *** REG GPSR1 - * GP33 == nCS5 is 1 - *** REG GPSR2 - * GP78 == nCS2 is 1 - * GP80 == nCS4 is 1 - */ -#define GPSR0_DFT 0x00308000 -#define GPSR1_DFT 0x00000002 -#define GPSR2_DFT 0x00014000 - -#define CONFIG_GPSR0_VAL GPSR0_DFT -#define CONFIG_GPSR1_VAL GPSR1_DFT -#define CONFIG_GPSR2_VAL GPSR2_DFT -#define CONFIG_GPSR3_VAL GPSR3_DFT - -/* - * set Direction "1" GPIO == output else input - * - ** REG GPDR0 - * GP03 == PWR_SDA is output - * GP04 == PWR_SCL is output - * GP15 == nCS1 is output - * GP20 == nSDCS2 is output - * GP21 == nSDCS3 is output - ** REG GPDR1 - * GP33 == nCS5 is output - ** REG GPDR2 - * GP78 == nCS2 is output - * GP80 == nCS4 is output - * GP90 == LED0 is output - * GP91 == LED1 is output - */ - -#define GPDR0_DFT 0x00308018 -#define GPDR1_DFT 0x00000002 -#define GPDR2_DFT 0x00014000 - -#define CONFIG_GPDR0_VAL GPDR0_DFT -#define CONFIG_GPDR1_VAL GPDR1_DFT -#define CONFIG_GPDR2_VAL GPDR2_DFT - -/* - * set Alternate Funktions - * - ** REG GAFR0_L - * GP15 == nCS1 is AF10 - ** REG GAFR0_U - * GP18 == RDY is AF01 - * GP20 == nSDCS2 is AF01 - * GP21 == nSDCS3 is AF01 - ** REG GAFR1_L - * GP33 == nCS5 is AF10 - ** REG GAFR2_L - * GP78 == nCS2 is AF10 - ** REG GAFR2_U - * GP80 == nCS4 is AF10 - */ - -#define GAFR0_L_DFT 0x80000000 -#define GAFR0_U_DFT 0x00000510 -#define GAFR1_L_DFT 0x00000008 -#define GAFR1_U_DFT 0x00000000 -#define GAFR2_L_DFT 0x20000000 -#define GAFR2_U_DFT 0x00000002 - -#define CONFIG_GAFR0_L_VAL GAFR0_L_DFT -#define CONFIG_GAFR0_U_VAL GAFR0_U_DFT -#define CONFIG_GAFR1_L_VAL GAFR1_L_DFT -#define CONFIG_GAFR1_U_VAL GAFR1_U_DFT -#define CONFIG_GAFR2_L_VAL GAFR2_L_DFT -#define CONFIG_GAFR2_U_VAL GAFR2_U_DFT - - -/* - * Power Manager Sleep Status Register (PSSR) - * - * [6] = 0 OTG pad is not holding it's state - * [5] = 1 Read Disable Hold: receivers of all gpio pins are disabled - * [4] = 1 gpio pins are held in their sleep mode state - * [3] = 0 The processor has not been placed in standby mode by - * configuring the PWRMODE register since STS was cleared - * by a reset or by software. - * [2] = 1 nVDD_FAULT has been asserted and caused the processor to - * enter deep-sleep mode. - * [1] = 1 nBATT_FAULT has been asserted and caused the processor to - * enter deep-sleep mode. - * [0] = 1 The processor was placed in sleep mode by configuring the - * PWRMODE register. - */ - -#define CONFIG_PSSR_VAL 0x37 - - -/********************************************************************* - * CONFIG PXA270 Chipselect settings * - *********************************************************************/ - -/* - * Memory settings - * - * This is the configuration for nCS1/0 -> PLD / flash - * configuration for nCS1: - * [31] 0 - Slower Device - * [30:28] 001 - CS deselect to CS time: 1*(2*MemClk) = 20 ns - * [27:24] 0010 - Address to data valid in bursts: (2+1)*MemClk = 30 ns - * [23:20] 1011 - " for first access: (11+2)*MemClk = 130 ns - * [19] 1 - 16 Bit bus width - * [18:16] 011 - burst RAM or FLASH - * configuration for nCS0 (J3 Flash): - * [15] 0 - Slower Device - * [14:12] 001 - CS deselect to CS time: 1*(2*MemClk) = 20 ns - * [11:08] 0010 - Address to data valid in bursts: (2+1)*MemClk = 30 ns - * [07:04] 1011 - " for first access: (11+2)*MemClk = 130 ns - * [03] 0 - 32 Bit bus width - * [02:00] 011 - burst RAM or FLASH - */ -#if PHYCORE_PXA270_USE_K3FLASH == 0 -#define CONFIG_MSC0_VAL 0x128C1262 -#else -/* configuration for nCS0 (K3 Flash): - * [15] 0 - Slower Device - * [14:12] 001 - CS deselect to CS time: 1*(2*MemClk) = 20 ns - * [11:08] 0010 - Address to data valid in bursts: (2+1)*MemClk = 30 ns - * [07:04] 1011 - " for first access: (11+2)*MemClk = 130 ns - * [03] 0 - 32 Bit bus width - * [02:00] 011 - burst RAM or FLASH - */ -#define CONFIG_MSC0_VAL 0x128C12B3 -#endif - -/* - * This is the configuration for nCS3/2 - * configuration for nCS3: POWER - * - * [31] 0 - Slower Device - * [30:28] 111 - RRR3: CS deselect to CS time: 7*(2*MemClk) = 140 ns - * [27:24] 1111 - RDN3: Address to data valid in bursts: (15+1)*MemClk = 160 ns - * [23:20] 1111 - RDF3: Address for first access: (23+1)*MemClk = 240 ns - * [19] 0 - 32 Bit bus width - * [18:16] 100 - variable latency I/O - * configuration for nCS2: PLD - * [15] 0 - Slower Device - * [14:12] 111 - RRR2: CS deselect to CS time: 7*(2*MemClk) = 140 ns - * [11:08] 1111 - RDN2: Address to data valid in bursts: (15+1)*MemClk = 160 ns - * [07:04] 1111 - RDF2: Address for first access: (23+1)*MemClk = 240 ns - * [03] 1 - 16 Bit bus width - * [02:00] 100 - variable latency I/O - */ -#define CONFIG_MSC1_VAL 0x128c128c - -/* - * This is the configuration for nCS5/4 - * - * configuration for nCS5: LAN Controller - * [31] 0 - Slower Device - * [30:28] 001 - RRR5: CS deselect to CS time: 1*(2*MemClk) = 20 ns - * [27:24] 0010 - RDN5: Address to data valid in bursts: (2+1)*MemClk = 30 ns - * [23:20] 0011 - RDF5: Address for first access: (3+1)*MemClk = 40 ns - * [19] 0 - 32 Bit bus width - * [18:16] 100 - variable latency I/O - * configuration for nCS4: USB - * [15] 0 - Slower Device - * [14:12] 111 - RRR4: CS deselect to CS time: 7*(2*MemClk) = 140 ns - * [11:08] 1111 - RDN4: Address to data valid in bursts: (15+1)*MemClk = 160 ns - * [07:04] 1111 - RDF4: Address for first access: (23+1)*MemClk = 240 ns - * [03] 1 - 16 Bit bus width - * [02:00] 100 - variable latency I/O - */ -#define CONFIG_MSC2_VAL 0x1234128C - -/********************************************************************* - * CONFIG PXA270 SDRAM settings * - *********************************************************************/ - -#define CONFIG_DRAM_BASE 0xa0000000 - - -/* MDCNFG: SDRAM Configuration Register - * - * [31] 0 - Stack1 - * [30] 0 - dcacx2 - * [20] 0 - reserved - * [31:29] 000 - reserved - * [28] 1 - SA1111 compatiblity mode - * [27] 1 - latch return data with return clock - * [26] 0 - alternate addressing for pair 2/3 - * [25:24] 10 - timings - * [23] 1 - internal banks in lower partition 2/3 (not used) - * [22:21] 10 - row address bits for partition 2/3 (not used) - * [20:19] 01 - column address bits for partition 2/3 (not used) - * [18] 0 - SDRAM partition 2/3 width is 32 bit - * [17] 0 - SDRAM partition 3 disabled - * [16] 0 - SDRAM partition 2 disabled - * [15] 0 - Stack1 - * [14] 0 - dcacx0 - * [13] 0 - Stack0 - * [12] 0 - SA1110 compatiblity mode - * [11] 1 - always 1 - * [10] 0 - no alternate addressing for pair 0/1 - * [09:08] 10 - tRP=2*MemClk CL=2 tRCD=2*MemClk tRAS=5*MemClk tRC=8*MemClk - * [7] 1 - 4 internal banks in lower partition pair - * [06:05] 10 - 13 row address bits for partition 0/1 - * [04:03] 01 - 9 column address bits for partition 0/1 - * [02] 0 - SDRAM partition 0/1 width is 32 bit - * [01] 0 - disable SDRAM partition 1 - * [00] 1 - enable SDRAM partition 0 - */ - -/* K4S561633*/ -#define CONFIG_MDCNFG_VAL 0x0AC90AC9 - -/* MDREFR: SDRAM Refresh Control Register - * - * [31] 0 - ALTREFA - * [30] 0 - ALTREFB - * [29] 1 - K0DB4 - * [28] 0 - reserved - * [27] 0 - reserved - * [26] 0 - reserved - * [25] 1 - K2FREE: not free running - * [24] 0 - K1FREE: not free running - * [23] 1 - K0FREE: not free running - * [22] 0 - SLFRSH: self refresh disabled - * [21] 0 - reserved - * [20] 0 - APD: no auto power down - * [19] 0 - K2DB2: SDCLK2 is MemClk - * [18] 0 - K2RUN: disable SDCLK2 - * [17] 0 - K1DB2: SDCLK1 is MemClk - * [16] 1 - K1RUN: enable SDCLK1 - * [15] 1 - E1PIN: SDRAM clock enable - * [14] 1 - K0DB2: SDCLK0 is MemClk - * [13] 0 - K0RUN: disable SDCLK0 - * [12] 0 - RESERVED - * [11:00] 000000011000 - (64ms/8192)*MemClkFreq/32 = 24 - */ -#define CONFIG_MDREFR_VAL 0x2281C018 - -/* MDMRS: Mode Register Set Configuration Register - * - * [31] 0 - reserved - * [30:23] 00000000- MDMRS2: SDRAM2/3 MRS Value. (not used) - * [22:20] 000 - MDCL2: SDRAM2/3 Cas Latency. (not used) - * [19] 0 - MDADD2: SDRAM2/3 burst Type. Fixed to sequential. (not used) - * [18:16] 010 - MDBL2: SDRAM2/3 burst Length. Fixed to 4. (not used) - * [15] 0 - reserved - * [14:07] 00000000- MDMRS0: SDRAM0/1 MRS Value. - * [06:04] 010 - MDCL0: SDRAM0/1 Cas Latency. - * [03] 0 - MDADD0: SDRAM0/1 burst Type. Fixed to sequential. - * [02:00] 010 - MDBL0: SDRAM0/1 burst Length. Fixed to 4. - */ -#define CONFIG_MDMRS_VAL 0x00020022 - -/********************************************************************* - * CONFIG PXA270 Clock generation * - *********************************************************************/ -#define CONFIG_FLYCNFG_VAL 0x00010001 -#define CONFIG_SXCNFG_VAL 0x40044004 -#define CONFIG_CKEN (CKEN_MEMC | CKEN_OSTIMER) - -#if PHYCORE_PXA270_SPEED == 520 -#define CONFIG_CCCR 0x00000290 /* Memory Clock is f. Table; N=2.5, L=16 => 16x13=208, 208x2,5=520 MHz */ -#elif PHYCORE_PXA270_SPEED == 260 -#define CONFIG_CCCR 0x02000288 /* Memory Clock is System-Bus Freq., N=2.5, L=8 => 8x13=104, 104x2,5=260 MHz */ -#else -#error You have specified an illegal speed. -#endif - -/********************************************************************* - * CONFIG PXA270 CF interface * - *********************************************************************/ -#define CONFIG_MECR_VAL 0x00000003 -#define CONFIG_MCMEM0_VAL 0x00010504 -#define CONFIG_MCMEM1_VAL 0x00010504 -#define CONFIG_MCATT0_VAL 0x00010504 -#define CONFIG_MCATT1_VAL 0x00010504 -#define CONFIG_MCIO0_VAL 0x00004715 -#define CONFIG_MCIO1_VAL 0x00004715 - -#endif /* __CONFIG_H */ diff --git a/arch/arm/boards/phytec-phycore-pxa270/env/init/mtdparts-nor b/arch/arm/boards/phytec-phycore-pxa270/env/init/mtdparts-nor deleted file mode 100644 index 4423943211..0000000000 --- a/arch/arm/boards/phytec-phycore-pxa270/env/init/mtdparts-nor +++ /dev/null @@ -1,6 +0,0 @@ -#!/bin/sh - -mtdparts="512k(nor0.barebox),256k(nor0.bareboxenv),4M(nor0.kernel),-(nor0.root)" -kernelname="physmap-flash.0" - -mtdparts-add -d nor0 -k ${kernelname} -p ${mtdparts} diff --git a/arch/arm/boards/phytec-phycore-pxa270/env/nv/linux.bootargs.console b/arch/arm/boards/phytec-phycore-pxa270/env/nv/linux.bootargs.console deleted file mode 100644 index 476b1fbe49..0000000000 --- a/arch/arm/boards/phytec-phycore-pxa270/env/nv/linux.bootargs.console +++ /dev/null @@ -1 +0,0 @@ -console=ttyS0,115200 diff --git a/arch/arm/boards/phytec-phycore-pxa270/lowlevel_init.S b/arch/arm/boards/phytec-phycore-pxa270/lowlevel_init.S deleted file mode 100644 index f8f1a037e0..0000000000 --- a/arch/arm/boards/phytec-phycore-pxa270/lowlevel_init.S +++ /dev/null @@ -1,448 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-or-later - -/* - * This was originally from the Lubbock u-boot port. - * - * Most of this taken from Redboot hal_platform_setup.h with cleanup - * - * NOTE: I haven't clean this up considerably, just enough to get it - * running. See hal_platform_setup.h for the source. See - * board/cradle/lowlevel_init.S for another PXA250 setup that is - * much cleaner. - */ - -#include <config.h> -#include <linux/sizes.h> -#include <mach/pxa/pxa-regs.h> -#include <mach/pxa/regs-ost.h> -#include <mach/pxa/regs-intc.h> -#include <asm/barebox-arm-head.h> -#include "config.h" - -#define GPSR0 0x40E00018 /* GPIO Pin Output Set Register GPIO <31:00> */ -#define GPSR1 0x40E0001C /* GPIO Pin Output Set Register GPIO <63:32> */ -#define GPSR2 0x40E00020 /* GPIO Pin Output Set Register GPIO <80:64> */ - -#define GPCR0 0x40E00024 /* GPIO Pin Output Clear Register GPIO <31:00> */ -#define GPCR1 0x40E00028 /* GPIO Pin Output Clear Register GPIO <63:32> */ -#define GPCR2 0x40E0002C /* GPIO Pin Output Clear Register GPIO <80:64> */ - -#define GPDR0 0x40E0000C /* GPIO Pin Direction Register GPIO <31:0o> */ -#define GPDR1 0x40E00010 /* GPIO Pin Direction Register GPIO <63:32> */ -#define GPDR2 0x40E00014 /* GPIO Pin Direction Register GPIO <80:64> */ - -#define GAFR0_L 0x40E00054 /* GPIO Alternate Function Select Register GPIO <15:00> */ -#define GAFR0_U 0x40E00058 /* GPIO Alternate Function Select Register GPIO <31:16> */ -#define GAFR1_L 0x40E0005C /* GPIO Alternate Function Select Register GPIO <47:32> */ -#define GAFR1_U 0x40E00060 /* GPIO Alternate Function Select Register GPIO <63:48> */ -#define GAFR2_L 0x40E00064 /* GPIO Alternate Function Select Register GPIO <79:64> */ -#define GAFR2_U 0x40E00068 /* GPIO Alternate Function Select Register GPIO <95:80> */ - -/* - * Memory setup - */ -.globl barebox_arm_reset_vector -barebox_arm_reset_vector: - bl arm_cpu_lowlevel_init - - @ Preserve r8/r7 i.e. kernel entry values - - @ Data cache might be active. - @ Be sure to flush kernel binary out of the cache, - @ whatever state it is, before it is turned off. - @ This is done by fetching through currently executed - @ memory to be sure we hit the same cache. - bic r2, pc, #0x1f - add r3, r2, #0x10000 @ 64 kb is quite enough... -1: ldr r0, [r2], #32 - teq r2, r3 - bne 1b - mcr p15, 0, r0, c7, c10, 4 @ drain WB - mcr p15, 0, r0, c7, c7, 0 @ flush I & D caches - - @ disabling MMU and caches - mrc p15, 0, r0, c1, c0, 0 @ read control reg - bic r0, r0, #0x05 @ clear DC, MMU - bic r0, r0, #0x1000 @ clear Icache - mcr p15, 0, r0, c1, c0, 0 - /* set output */ - ldr r0, =GPSR0 - ldr r1, =CONFIG_GPSR0_VAL - str r1, [r0] - - ldr r0, =GPSR1 - ldr r1, =CONFIG_GPSR1_VAL - str r1, [r0] - - ldr r0, =GPSR2 - ldr r1, =CONFIG_GPSR2_VAL - str r1, [r0] - - /* set direction */ - ldr r0, =GPDR0 - ldr r1, =CONFIG_GPDR0_VAL - str r1, [r0] - - ldr r0, =GPDR1 - ldr r1, =CONFIG_GPDR1_VAL - str r1, [r0] - - ldr r0, =GPDR2 - ldr r1, =CONFIG_GPDR2_VAL - str r1, [r0] - - /* alternate function */ - ldr r0, =GAFR0_L - ldr r1, =CONFIG_GAFR0_L_VAL - str r1, [r0] - - ldr r0, =GAFR0_U - ldr r1, =CONFIG_GAFR0_U_VAL - str r1, [r0] - - ldr r0, =GAFR1_L - ldr r1, =CONFIG_GAFR1_L_VAL - str r1, [r0] - - ldr r0, =GAFR1_U - ldr r1, =CONFIG_GAFR1_U_VAL - str r1, [r0] - - ldr r0, =GAFR2_L - ldr r1, =CONFIG_GAFR2_L_VAL - str r1, [r0] - - ldr r0, =GAFR2_U - ldr r1, =CONFIG_GAFR2_U_VAL - str r1, [r0] - - /* enable GPIO pins */ - ldr r0, =PSSR - ldr r1, =CONFIG_PSSR_VAL - str r1, [r0] - - /* -------------------------------------------------------------------- */ - /* Enable memory interface */ - /* */ - /* The sequence below is based on the recommended init steps */ - /* detailed in the Intel PXA250 Operating Systems Developers Guide, */ - /* Chapter 10. */ - /* -------------------------------------------------------------------- */ - - /* -------------------------------------------------------------------- */ - /* Step 1: Wait for at least 200 microsedonds to allow internal */ - /* clocks to settle. Only necessary after hard reset... */ - /* FIXME: can be optimized later */ - /* -------------------------------------------------------------------- */ - - ldr r3, =OSCR /* reset the OS Timer Count to zero */ - mov r2, #0 - str r2, [r3] - ldr r4, =0x300 /* really 0x2E1 is about 200usec, */ - /* so 0x300 should be plenty */ -1: - ldr r2, [r3] - cmp r4, r2 - bgt 1b - - cmp pc, #0xa0000000 - bls mem_init - cmp pc, #0xb0000000 - bhi mem_init - b skip_mem_init - -mem_init: - ldr r1, =MDCNFG /* get memory controller base addr. */ - - /* -------------------------------------------------------------------- */ - /* Step 2a: Initialize Asynchronous static memory controller */ - /* -------------------------------------------------------------------- */ - - /* MSC registers: timing, bus width, mem type */ - - /* MSC0: nCS(0,1) */ - ldr r2, =CONFIG_MSC0_VAL - str r2, [r1, #MSC0_OFFSET] - ldr r2, [r1, #MSC0_OFFSET] /* read back to ensure */ - /* that data latches */ - /* MSC1: nCS(2,3) */ - ldr r2, =CONFIG_MSC1_VAL - str r2, [r1, #MSC1_OFFSET] - ldr r2, [r1, #MSC1_OFFSET] - - /* MSC2: nCS(4,5) */ - ldr r2, =CONFIG_MSC2_VAL - str r2, [r1, #MSC2_OFFSET] - ldr r2, [r1, #MSC2_OFFSET] - - /* -------------------------------------------------------------------- */ - /* Step 2b: Initialize Card Interface */ - /* -------------------------------------------------------------------- */ - - /* MECR: Memory Expansion Card Register */ - ldr r2, =CONFIG_MECR_VAL - str r2, [r1, #MECR_OFFSET] - ldr r2, [r1, #MECR_OFFSET] - - /* MCMEM0: Card Interface slot 0 timing */ - ldr r2, =CONFIG_MCMEM0_VAL - str r2, [r1, #MCMEM0_OFFSET] - ldr r2, [r1, #MCMEM0_OFFSET] - - /* MCMEM1: Card Interface slot 1 timing */ - ldr r2, =CONFIG_MCMEM1_VAL - str r2, [r1, #MCMEM1_OFFSET] - ldr r2, [r1, #MCMEM1_OFFSET] - - /* MCATT0: Card Interface Attribute Space Timing, slot 0 */ - ldr r2, =CONFIG_MCATT0_VAL - str r2, [r1, #MCATT0_OFFSET] - ldr r2, [r1, #MCATT0_OFFSET] - - /* MCATT1: Card Interface Attribute Space Timing, slot 1 */ - ldr r2, =CONFIG_MCATT1_VAL - str r2, [r1, #MCATT1_OFFSET] - ldr r2, [r1, #MCATT1_OFFSET] - - /* MCIO0: Card Interface I/O Space Timing, slot 0 */ - ldr r2, =CONFIG_MCIO0_VAL - str r2, [r1, #MCIO0_OFFSET] - ldr r2, [r1, #MCIO0_OFFSET] - - /* MCIO1: Card Interface I/O Space Timing, slot 1 */ - ldr r2, =CONFIG_MCIO1_VAL - str r2, [r1, #MCIO1_OFFSET] - ldr r2, [r1, #MCIO1_OFFSET] - - /* -------------------------------------------------------------------- */ - /* Step 2c: Write FLYCNFG FIXME: what's that??? */ - /* -------------------------------------------------------------------- */ - ldr r2, =CONFIG_FLYCNFG_VAL - str r2, [r1, #FLYCNFG_OFFSET] - str r2, [r1, #FLYCNFG_OFFSET] - - /* -------------------------------------------------------------------- */ - /* Step 2d: Initialize Timing for Sync Memory (SDCLK0) */ - /* -------------------------------------------------------------------- */ - - /* Before accessing MDREFR we need a valid DRI field, so we set */ - /* this to power on defaults + DRI field. */ - - ldr r4, [r1, #MDREFR_OFFSET] - ldr r2, =0xFFF - bic r4, r4, r2 - - ldr r3, =CONFIG_MDREFR_VAL - and r3, r3, r2 - - orr r4, r4, r3 - str r4, [r1, #MDREFR_OFFSET] /* write back MDREFR */ - - orr r4, r4, #MDREFR_K0RUN - orr r4, r4, #MDREFR_K0DB4 - orr r4, r4, #MDREFR_K0FREE - orr r4, r4, #MDREFR_K2FREE - orr r4, r4, #MDREFR_K0DB2 - orr r4, r4, #MDREFR_K1DB2 - bic r4, r4, #MDREFR_K1FREE - - str r4, [r1, #MDREFR_OFFSET] /* write back MDREFR */ - ldr r4, [r1, #MDREFR_OFFSET] - - /* Note: preserve the mdrefr value in r4 */ - - - /* -------------------------------------------------------------------- */ - /* Step 3: Initialize Synchronous Static Memory (Flash/Peripherals) */ - /* -------------------------------------------------------------------- */ - - /* Initialize SXCNFG register. Assert the enable bits */ - - /* - * Write SXMRS to cause an MRS command to all enabled banks of - * synchronous static memory. Note that SXLCR need not be - * written at this time. - */ - ldr r2, =CONFIG_SXCNFG_VAL - str r2, [r1, #SXCNFG_OFFSET] - - /* -------------------------------------------------------------------- */ - /* Step 4: Initialize SDRAM */ - /* -------------------------------------------------------------------- */ - bic r4, r4, #(MDREFR_K1FREE | MDREFR_K0FREE) - - orr r4, r4, #MDREFR_K1RUN - orr r4, r4, #MDREFR_K2FREE - bic r4, r4, #MDREFR_K2DB2 - str r4, [r1, #MDREFR_OFFSET] - ldr r4, [r1, #MDREFR_OFFSET] - - bic r4, r4, #MDREFR_SLFRSH - str r4, [r1, #MDREFR_OFFSET] - ldr r4, [r1, #MDREFR_OFFSET] - - orr r4, r4, #MDREFR_E1PIN - str r4, [r1, #MDREFR_OFFSET] - ldr r4, [r1, #MDREFR_OFFSET] - - nop - nop - - - /* - * Step 4d: write MDCNFG with MDCNFG:DEx deasserted - * (set to 0), to configure but not enable each SDRAM - * partition pair. - */ - ldr r4, =CONFIG_MDCNFG_VAL - bic r4, r4, #(MDCNFG_DE0|MDCNFG_DE1) - bic r4, r4, #(MDCNFG_DE2|MDCNFG_DE3) - - str r4, [r1, #MDCNFG_OFFSET] /* write back MDCNFG */ - ldr r4, [r1, #MDCNFG_OFFSET] - - - /* - * Step 4e: Wait for the clock to the SDRAMs to stabilize, - * 100..200 usec. - */ - ldr r3, =OSCR /* reset the OS Timer Count to zero */ - mov r2, #0 - str r2, [r3] - ldr r4, =0x300 /* really 0x2E1 is about 200 usec, */ - /* so 0x300 should be plenty */ -1: - ldr r2, [r3] - cmp r4, r2 - bgt 1b - - - /* Step 4f: Trigger a number (usually 8) refresh cycles by */ - /* attempting non-burst read or write accesses to disabled */ - /* SDRAM, as commonly specified in the power up sequence */ - /* documented in SDRAM data sheets. The address(es) used */ - /* for this purpose must not be cacheable. */ - ldr r3, =CONFIG_DRAM_BASE - str r2, [r3] - str r2, [r3] - str r2, [r3] - str r2, [r3] - str r2, [r3] - str r2, [r3] - str r2, [r3] - str r2, [r3] - - - /* - * Step 4g: Write MDCNFG with enable bits asserted - * (MDCNFG:DEx set to 1) - */ - ldr r3, [r1, #MDCNFG_OFFSET] - mov r4, r3 - orr r3, r3, #MDCNFG_DE0 - str r3, [r1, #MDCNFG_OFFSET] - mov r0, r3 - - /* Step 4h: Write MDMRS. */ - ldr r2, =CONFIG_MDMRS_VAL - str r2, [r1, #MDMRS_OFFSET] - - /* enable APD */ - ldr r3, [r1, #MDREFR_OFFSET] - orr r3, r3, #MDREFR_APD - str r3, [r1, #MDREFR_OFFSET] - - /* We are finished with Intel's memory controller initialisation */ -skip_mem_init: - -wakeup: - /* Are we waking from sleep? */ - ldr r0, =RCSR - ldr r1, [r0] - and r1, r1, #(RCSR_GPR | RCSR_SMR | RCSR_WDR | RCSR_HWR) - str r1, [r0] - teq r1, #RCSR_SMR - - bne initirqs - - ldr r0, =PSSR - mov r1, #PSSR_PH - str r1, [r0] - - /* if so, resume at PSPR */ - ldr r0, =PSPR - ldr r1, [r0] - mov pc, r1 - - /* -------------------------------------------------------------------- */ - /* Disable (mask) all interrupts at interrupt controller */ - /* -------------------------------------------------------------------- */ - -initirqs: - mov r1, #0 /* clear int. level register (IRQ, not FIQ) */ - ldr r2, =ICLR - str r1, [r2] - - ldr r2, =ICMR /* mask all interrupts at the controller */ - str r1, [r2] - - /* -------------------------------------------------------------------- */ - /* Clock initialisation */ - /* -------------------------------------------------------------------- */ - -initclks: - /* Disable the peripheral clocks, and set the core clock frequency */ - - /* Turn Off on-chip peripheral clocks (except for memory) */ - /* for re-configuration. */ - ldr r1, =CKEN - ldr r2, =CONFIG_CKEN - str r2, [r1] - - /* ... and write the core clock config register */ - ldr r2, =CONFIG_CCCR - ldr r1, =CCCR - str r2, [r1] - - /* Turn on turbo mode */ - mrc p14, 0, r2, c6, c0, 0 - orr r2, r2, #0xB /* Turbo, Fast-Bus, Freq change */ - mcr p14, 0, r2, c6, c0, 0 - - /* Re-write MDREFR */ - ldr r1, =MDCNFG - ldr r2, [r1, #MDREFR_OFFSET] - str r2, [r1, #MDREFR_OFFSET] - - /* enable the 32Khz oscillator for RTC and PowerManager */ - ldr r1, =OSCC - mov r2, #OSCC_OON - str r2, [r1] - - /* Interrupt init: Mask all interrupts */ - ldr r0, =ICMR /* enable no sources */ - mov r1, #0 - str r1, [r0] - /* FIXME */ - -#ifdef NODEBUG - /* Disable software and data breakpoints */ - mov r0, #0 - mcr p15, 0, r0, c14, c8, 0 /* ibcr0 */ - mcr p15, 0, r0, c14, c9, 0 /* ibcr1 */ - mcr p15, 0, r0, c14, c4, 0 /* dbcon */ - - /* Enable all debug functionality */ - mov r0, #0x80000000 - mcr p14, 0, r0, c10, c0, 0 /* dcsr */ -#endif - - /* -------------------------------------------------------------------- */ - /* End lowlevel_init */ - /* -------------------------------------------------------------------- */ - -endlowlevel_init: - mov r0, #0xa0000000 - mov r1, #SZ_64M - mov r2, #0 - b barebox_arm_entry diff --git a/arch/arm/boards/zylonite/Makefile b/arch/arm/boards/zylonite/Makefile deleted file mode 100644 index da63d2625f..0000000000 --- a/arch/arm/boards/zylonite/Makefile +++ /dev/null @@ -1,4 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0-only - -obj-y += board.o -lwl-y += lowlevel.o diff --git a/arch/arm/boards/zylonite/board.c b/arch/arm/boards/zylonite/board.c deleted file mode 100644 index 04cb34754c..0000000000 --- a/arch/arm/boards/zylonite/board.c +++ /dev/null @@ -1,93 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-or-later -// SPDX-FileCopyrightText: 2014 Robert Jarzmik <[email protected]> - -#include <common.h> - -#include <driver.h> -#include <environment.h> -#include <fs.h> -#include <gpio.h> -#include <init.h> -#include <led.h> -#include <platform_data/eth-smc91111.h> -#include <platform_data/mtd-nand-mrvl.h> -#include <pwm.h> -#include <linux/clk.h> -#include <linux/clkdev.h> -#include <linux/sizes.h> - -#include <mach/pxa/devices.h> -#include <mach/pxa/mfp-pxa3xx.h> -#include <mach/pxa/pxa-regs.h> - -#include <asm/armlinux.h> -#include <asm/io.h> -#include <asm/mmu.h> -#include <asm/mach-types.h> - -static struct smc91c111_pdata smsc91x_pdata; -static struct mrvl_nand_platform_data nand_pdata = { - .keep_config = 0, - .flash_bbt = 1, -}; - -static mfp_cfg_t pxa310_mfp_cfg[] = { - /* FFUART */ - MFP_CFG_LPM(GPIO99, AF1, FLOAT), /* GPIO99_UART1_RXD */ - MFP_CFG_LPM(GPIO100, AF1, FLOAT), /* GPIO100_UART1_RXD */ - MFP_CFG_LPM(GPIO101, AF1, FLOAT), /* GPIO101_UART1_CTS */ - MFP_CFG_LPM(GPIO106, AF1, FLOAT), /* GPIO106_UART1_CTS */ - - /* Ethernet */ - MFP_CFG(GPIO2, AF1), /* GPIO2_nCS3 */ -}; - -static int zylonite_devices_init(void) -{ - struct clk *clk; - - armlinux_set_architecture(MACH_TYPE_ZYLONITE); - pxa_add_uart((void *)0x40100000, 0); - add_generic_device("smc91c111", DEVICE_ID_DYNAMIC, NULL, - 0x14000300, 0x100000, IORESOURCE_MEM, - &smsc91x_pdata); - clk = clk_get_sys("nand", NULL); - if (!IS_ERR(clk)) - clkdev_add_physbase(clk, 0x43100000, NULL); - add_generic_device("mrvl_nand", DEVICE_ID_DYNAMIC, NULL, - 0x43100000, 0x1000, IORESOURCE_MEM, &nand_pdata); - devfs_add_partition("nand0", SZ_1M, SZ_256K, DEVFS_PARTITION_FIXED, - "env0"); - return 0; -} -device_initcall(zylonite_devices_init); - -static int zylonite_coredevice_init(void) -{ - barebox_set_model("Zylonite"); - barebox_set_hostname("zylonite"); - - mfp_init(); - if (cpu_is_pxa310()) - pxa3xx_mfp_config(pxa310_mfp_cfg, ARRAY_SIZE(pxa310_mfp_cfg)); - CKENA |= CKEN_NAND | CKEN_SMC | CKEN_FFUART | CKEN_GPIO; - /* - * Configure Ethernet controller : - * MCS1: setup VLIO on nCS3, with 15 DF_SCLK cycles (max) for hold, - * setup and assertion times - * CSADRCFG3: DFI AA/D multiplexing VLIO, addr split at bit <16>, full - * latched mode, 7 DF_SCLK cycles (max) for nLUA and nLLA. - */ - MSC1 = 0x7ffc0000 | (MSC1 & 0x0000ffff); - CSADRCFG3 = 0x003e080b; - - return 0; -} -coredevice_initcall(zylonite_coredevice_init); - -static int zylonite_mem_init(void) -{ - arm_add_mem_device("ram0", 0x80000000, 64 * 1024 * 1024); - return 0; -} -mem_initcall(zylonite_mem_init); diff --git a/arch/arm/boards/zylonite/env/boot/nand-ubi b/arch/arm/boards/zylonite/env/boot/nand-ubi deleted file mode 100644 index 2231738224..0000000000 --- a/arch/arm/boards/zylonite/env/boot/nand-ubi +++ /dev/null @@ -1,5 +0,0 @@ -#!/bin/sh - -global.bootm.image="/dev/nand0.kernel" -#global.bootm.oftree="/env/oftree" -global.linux.bootargs.dyn.root="root=ubi0:linux_root ubi.mtd=nand.root rootfstype=ubifs" diff --git a/arch/arm/boards/zylonite/env/init/mtdparts-nand b/arch/arm/boards/zylonite/env/init/mtdparts-nand deleted file mode 100644 index 749318b59e..0000000000 --- a/arch/arm/boards/zylonite/env/init/mtdparts-nand +++ /dev/null @@ -1,6 +0,0 @@ -#!/bin/sh - -mtdparts="128k@0(TIMH)ro,128k@128k(OBMI)ro,768k@256k(barebox),256k@1024k(barebox-env),12M@1280k(kernel),38016k@13568k(root)" -kernelname="pxa3xx_nand-0" - -mtdparts-add -d nand0 -k ${kernelname} -p ${mtdparts} diff --git a/arch/arm/boards/zylonite/env/nv/hostname b/arch/arm/boards/zylonite/env/nv/hostname deleted file mode 100644 index 6e6d865eda..0000000000 --- a/arch/arm/boards/zylonite/env/nv/hostname +++ /dev/null @@ -1 +0,0 @@ -zylonite diff --git a/arch/arm/boards/zylonite/env/nv/linux.bootargs.base b/arch/arm/boards/zylonite/env/nv/linux.bootargs.base deleted file mode 100644 index 317f8b16a1..0000000000 --- a/arch/arm/boards/zylonite/env/nv/linux.bootargs.base +++ /dev/null @@ -1 +0,0 @@ -ram=64M diff --git a/arch/arm/boards/zylonite/env/nv/linux.bootargs.console b/arch/arm/boards/zylonite/env/nv/linux.bootargs.console deleted file mode 100644 index 476b1fbe49..0000000000 --- a/arch/arm/boards/zylonite/env/nv/linux.bootargs.console +++ /dev/null @@ -1 +0,0 @@ -console=ttyS0,115200 diff --git a/arch/arm/boards/zylonite/lowlevel.c b/arch/arm/boards/zylonite/lowlevel.c deleted file mode 100644 index 972fd34761..0000000000 --- a/arch/arm/boards/zylonite/lowlevel.c +++ /dev/null @@ -1,12 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-only - -#include <common.h> -#include <linux/sizes.h> -#include <asm/barebox-arm-head.h> -#include <asm/barebox-arm.h> - -void __naked barebox_arm_reset_vector(uint32_t r0, uint32_t r1, uint32_t r2) -{ - arm_cpu_lowlevel_init(); - barebox_arm_entry(0x80000000, SZ_64M, NULL); -} diff --git a/arch/arm/configs/lubbock_defconfig b/arch/arm/configs/lubbock_defconfig deleted file mode 100644 index 78f2236648..0000000000 --- a/arch/arm/configs/lubbock_defconfig +++ /dev/null @@ -1,100 +0,0 @@ -CONFIG_ARCH_PXA=y -CONFIG_AEABI=y -CONFIG_ARM_BOARD_APPEND_ATAG=y -CONFIG_ARM_OPTIMZED_STRING_FUNCTIONS=y -CONFIG_ARM_UNWIND=y -# CONFIG_BANNER is not set -CONFIG_MMU=y -CONFIG_BAREBOX_MAX_IMAGE_SIZE=0x100000 -CONFIG_BAREBOX_MAX_BARE_INIT_SIZE=0x80000 -CONFIG_MALLOC_SIZE=0x1000000 -CONFIG_EXPERIMENTAL=y -CONFIG_MODULES=y -CONFIG_KALLSYMS=y -CONFIG_PROMPT="lubbock-barebox:" -CONFIG_HUSH_FANCY_PROMPT=y -CONFIG_CMDLINE_EDITING=y -CONFIG_AUTO_COMPLETE=y -CONFIG_MENU=y -CONFIG_BOOTM_SHOW_TYPE=y -CONFIG_BOOTM_VERBOSE=y -CONFIG_BOOTM_INITRD=y -CONFIG_BOOTM_OFTREE=y -CONFIG_CONSOLE_ACTIVATE_ALL=y -CONFIG_DEFAULT_ENVIRONMENT_GENERIC_NEW=y -CONFIG_DEFAULT_ENVIRONMENT_PATH="arch/arm/boards/lubbock/env" -CONFIG_RESET_SOURCE=y -CONFIG_CMD_DMESG=y -CONFIG_LONGHELP=y -CONFIG_CMD_IOMEM=y -CONFIG_CMD_MEMINFO=y -CONFIG_CMD_GO=y -CONFIG_CMD_LOADB=y -CONFIG_CMD_LOADS=y -CONFIG_CMD_LOADY=y -CONFIG_CMD_RESET=y -CONFIG_CMD_SAVES=y -CONFIG_CMD_PARTITION=y -CONFIG_CMD_UBIFORMAT=y -CONFIG_CMD_EXPORT=y -CONFIG_CMD_LOADENV=y -CONFIG_CMD_PRINTENV=y -CONFIG_CMD_SAVEENV=y -CONFIG_CMD_FILETYPE=y -CONFIG_CMD_LN=y -CONFIG_CMD_UNCOMPRESS=y -CONFIG_CMD_LET=y -CONFIG_CMD_MSLEEP=y -CONFIG_CMD_SLEEP=y -CONFIG_CMD_DHCP=y -CONFIG_CMD_MIITOOL=y -CONFIG_CMD_PING=y -CONFIG_CMD_TFTP=y -CONFIG_CMD_ECHO_E=y -CONFIG_CMD_EDIT=y -CONFIG_CMD_MENU=y -CONFIG_CMD_MENU_MANAGEMENT=y -CONFIG_CMD_READLINE=y -CONFIG_CMD_TIMEOUT=y -CONFIG_CMD_CRC=y -CONFIG_CMD_CRC_CMP=y -CONFIG_CMD_MEMTEST=y -CONFIG_CMD_MM=y -CONFIG_CMD_DETECT=y -CONFIG_CMD_FLASH=y -CONFIG_CMD_GPIO=y -CONFIG_CMD_LED=y -CONFIG_CMD_POWEROFF=y -CONFIG_CMD_LSMOD=y -CONFIG_CMD_OF_NODE=y -CONFIG_CMD_OF_PROPERTY=y -CONFIG_CMD_OFTREE=y -CONFIG_CMD_TIME=y -CONFIG_NET=y -CONFIG_NET_NETCONSOLE=y -CONFIG_OFDEVICE=y -CONFIG_OF_BAREBOX_DRIVERS=y -CONFIG_DRIVER_SERIAL_PXA=y -CONFIG_DRIVER_NET_SMC91111=y -# CONFIG_SPI is not set -CONFIG_MTD=y -CONFIG_DRIVER_CFI=y -# CONFIG_DRIVER_CFI_AMD is not set -CONFIG_CFI_BUFFER_WRITE=y -CONFIG_MTD_UBI=y -CONFIG_MCI=y -CONFIG_MCI_PXA=y -CONFIG_LED=y -CONFIG_LED_GPIO=y -CONFIG_KEYBOARD_GPIO=y -CONFIG_GENERIC_PHY=y -CONFIG_FS_CRAMFS=y -CONFIG_FS_EXT4=y -CONFIG_FS_TFTP=y -CONFIG_FS_FAT=y -CONFIG_FS_FAT_WRITE=y -CONFIG_FS_FAT_LFN=y -CONFIG_FS_UBIFS=y -CONFIG_FS_UBIFS_COMPRESSION_LZO=y -CONFIG_FS_UBIFS_COMPRESSION_ZLIB=y -CONFIG_BZLIB=y diff --git a/arch/arm/configs/mainstone_defconfig b/arch/arm/configs/mainstone_defconfig deleted file mode 100644 index d452885e6d..0000000000 --- a/arch/arm/configs/mainstone_defconfig +++ /dev/null @@ -1,103 +0,0 @@ -CONFIG_ARCH_PXA=y -CONFIG_ARCH_PXA27X=y -CONFIG_AEABI=y -CONFIG_ARM_BOARD_APPEND_ATAG=y -CONFIG_ARM_OPTIMZED_STRING_FUNCTIONS=y -CONFIG_ARM_UNWIND=y -# CONFIG_BANNER is not set -CONFIG_MMU=y -CONFIG_BAREBOX_MAX_IMAGE_SIZE=0x100000 -CONFIG_BAREBOX_MAX_BARE_INIT_SIZE=0x80000 -CONFIG_MALLOC_SIZE=0x1000000 -CONFIG_EXPERIMENTAL=y -CONFIG_MODULES=y -CONFIG_KALLSYMS=y -CONFIG_PROMPT="mainstone-barebox:" -CONFIG_HUSH_FANCY_PROMPT=y -CONFIG_CMDLINE_EDITING=y -CONFIG_AUTO_COMPLETE=y -CONFIG_MENU=y -CONFIG_BOOTM_SHOW_TYPE=y -CONFIG_BOOTM_VERBOSE=y -CONFIG_BOOTM_INITRD=y -CONFIG_BOOTM_OFTREE=y -CONFIG_CONSOLE_ACTIVATE_ALL=y -CONFIG_DEFAULT_ENVIRONMENT_GENERIC_NEW=y -CONFIG_DEFAULT_ENVIRONMENT_PATH="arch/arm/boards/mainstone/env" -CONFIG_RESET_SOURCE=y -CONFIG_CMD_DMESG=y -CONFIG_LONGHELP=y -CONFIG_CMD_IOMEM=y -CONFIG_CMD_MEMINFO=y -CONFIG_CMD_GO=y -CONFIG_CMD_LOADB=y -CONFIG_CMD_LOADS=y -CONFIG_CMD_LOADY=y -CONFIG_CMD_RESET=y -CONFIG_CMD_SAVES=y -CONFIG_CMD_PARTITION=y -CONFIG_CMD_UBIFORMAT=y -CONFIG_CMD_EXPORT=y -CONFIG_CMD_LOADENV=y -CONFIG_CMD_PRINTENV=y -CONFIG_CMD_MAGICVAR=y -CONFIG_CMD_MAGICVAR_HELP=y -CONFIG_CMD_SAVEENV=y -CONFIG_CMD_FILETYPE=y -CONFIG_CMD_LN=y -CONFIG_CMD_UNCOMPRESS=y -CONFIG_CMD_LET=y -CONFIG_CMD_MSLEEP=y -CONFIG_CMD_SLEEP=y -CONFIG_CMD_DHCP=y -CONFIG_CMD_MIITOOL=y -CONFIG_CMD_PING=y -CONFIG_CMD_TFTP=y -CONFIG_CMD_ECHO_E=y -CONFIG_CMD_EDIT=y -CONFIG_CMD_MENU=y -CONFIG_CMD_MENU_MANAGEMENT=y -CONFIG_CMD_READLINE=y -CONFIG_CMD_TIMEOUT=y -CONFIG_CMD_CRC=y -CONFIG_CMD_CRC_CMP=y -CONFIG_CMD_MEMTEST=y -CONFIG_CMD_MM=y -CONFIG_CMD_DETECT=y -CONFIG_CMD_FLASH=y -CONFIG_CMD_GPIO=y -CONFIG_CMD_LED=y -CONFIG_CMD_POWEROFF=y -CONFIG_CMD_LSMOD=y -CONFIG_CMD_OF_NODE=y -CONFIG_CMD_OF_PROPERTY=y -CONFIG_CMD_OFTREE=y -CONFIG_CMD_TIME=y -CONFIG_NET=y -CONFIG_NET_NETCONSOLE=y -CONFIG_OFDEVICE=y -CONFIG_OF_BAREBOX_DRIVERS=y -CONFIG_DRIVER_SERIAL_PXA=y -CONFIG_DRIVER_NET_SMC91111=y -# CONFIG_SPI is not set -CONFIG_MTD=y -CONFIG_DRIVER_CFI=y -# CONFIG_DRIVER_CFI_AMD is not set -CONFIG_CFI_BUFFER_WRITE=y -CONFIG_MTD_UBI=y -CONFIG_MCI=y -CONFIG_MCI_PXA=y -CONFIG_LED=y -CONFIG_LED_GPIO=y -CONFIG_KEYBOARD_GPIO=y -CONFIG_GENERIC_PHY=y -CONFIG_FS_CRAMFS=y -CONFIG_FS_EXT4=y -CONFIG_FS_TFTP=y -CONFIG_FS_FAT=y -CONFIG_FS_FAT_WRITE=y -CONFIG_FS_FAT_LFN=y -CONFIG_FS_UBIFS=y -CONFIG_FS_UBIFS_COMPRESSION_LZO=y -CONFIG_FS_UBIFS_COMPRESSION_ZLIB=y -CONFIG_BZLIB=y diff --git a/arch/arm/configs/mioa701_defconfig b/arch/arm/configs/mioa701_defconfig deleted file mode 100644 index 991fca0d7b..0000000000 --- a/arch/arm/configs/mioa701_defconfig +++ /dev/null @@ -1,104 +0,0 @@ -CONFIG_ARCH_PXA=y -CONFIG_ARCH_PXA27X=y -CONFIG_AEABI=y -CONFIG_ARM_BOARD_APPEND_ATAG=y -CONFIG_ARM_OPTIMZED_STRING_FUNCTIONS=y -CONFIG_ARM_UNWIND=y -# CONFIG_BANNER is not set -CONFIG_MMU=y -CONFIG_BAREBOX_MAX_IMAGE_SIZE=0x100000 -CONFIG_BAREBOX_MAX_BARE_INIT_SIZE=0x80000 -CONFIG_MALLOC_SIZE=0x1000000 -CONFIG_EXPERIMENTAL=y -CONFIG_MODULES=y -CONFIG_KALLSYMS=y -CONFIG_HUSH_FANCY_PROMPT=y -CONFIG_CMDLINE_EDITING=y -CONFIG_AUTO_COMPLETE=y -CONFIG_MENU=y -CONFIG_BOOTM_SHOW_TYPE=y -CONFIG_BOOTM_VERBOSE=y -CONFIG_BOOTM_INITRD=y -CONFIG_BOOTM_OFTREE=y -CONFIG_FLEXIBLE_BOOTARGS=y -CONFIG_DEFAULT_ENVIRONMENT_PATH="arch/arm/boards/mioa701/env" -CONFIG_RESET_SOURCE=y -CONFIG_LONGHELP=y -CONFIG_CMD_IOMEM=y -CONFIG_CMD_MEMINFO=y -CONFIG_CMD_BOOT=y -CONFIG_CMD_GO=y -CONFIG_CMD_LOADB=y -CONFIG_CMD_LOADS=y -CONFIG_CMD_LOADY=y -CONFIG_CMD_RESET=y -CONFIG_CMD_SAVES=y -CONFIG_CMD_PARTITION=y -CONFIG_CMD_AUTOMOUNT=y -CONFIG_CMD_UBIFORMAT=y -CONFIG_CMD_EXPORT=y -CONFIG_CMD_GLOBAL=y -CONFIG_CMD_PRINTENV=y -CONFIG_CMD_SAVEENV=y -CONFIG_CMD_BASENAME=y -CONFIG_CMD_DIRNAME=y -CONFIG_CMD_FILETYPE=y -CONFIG_CMD_LN=y -CONFIG_CMD_READLINK=y -CONFIG_CMD_UNCOMPRESS=y -CONFIG_CMD_GETOPT=y -CONFIG_CMD_LET=y -CONFIG_CMD_MSLEEP=y -CONFIG_CMD_SLEEP=y -CONFIG_CMD_ECHO_E=y -CONFIG_CMD_EDIT=y -CONFIG_CMD_LOGIN=y -CONFIG_CMD_MENU=y -CONFIG_CMD_MENU_MANAGEMENT=y -CONFIG_CMD_PASSWD=y -CONFIG_CMD_SPLASH=y -CONFIG_CMD_READLINE=y -CONFIG_CMD_TIMEOUT=y -CONFIG_CMD_CRC=y -CONFIG_CMD_CRC_CMP=y -CONFIG_CMD_MEMTEST=y -CONFIG_CMD_MM=y -CONFIG_CMD_DETECT=y -CONFIG_CMD_FLASH=y -CONFIG_CMD_GPIO=y -CONFIG_CMD_LED=y -CONFIG_CMD_POWEROFF=y -CONFIG_CMD_LSMOD=y -CONFIG_CMD_OF_NODE=y -CONFIG_CMD_OF_PROPERTY=y -CONFIG_CMD_OFTREE=y -CONFIG_CMD_TIME=y -CONFIG_OFDEVICE=y -CONFIG_OF_BAREBOX_DRIVERS=y -CONFIG_DRIVER_SERIAL_PXA=y -# CONFIG_SPI is not set -CONFIG_MTD=y -CONFIG_MTD_RAW_DEVICE=y -CONFIG_MTD_DOCG3=y -CONFIG_MTD_UBI=y -CONFIG_USB_GADGET=y -CONFIG_USB_GADGET_SERIAL=y -CONFIG_VIDEO=y -CONFIG_DRIVER_VIDEO_PXA=y -CONFIG_MCI=y -CONFIG_MCI_PXA=y -CONFIG_LED=y -CONFIG_LED_GPIO=y -CONFIG_KEYBOARD_GPIO=y -CONFIG_FS_CRAMFS=y -CONFIG_FS_EXT4=y -CONFIG_FS_FAT=y -CONFIG_FS_FAT_WRITE=y -CONFIG_FS_FAT_LFN=y -CONFIG_FS_UBIFS=y -CONFIG_FS_UBIFS_COMPRESSION_LZO=y -CONFIG_FS_UBIFS_COMPRESSION_ZLIB=y -CONFIG_BZLIB=y -CONFIG_BMP=y -CONFIG_PNG=y -CONFIG_DIGEST_SHA256_GENERIC=y diff --git a/arch/arm/configs/phytec-phycore-pxa270_defconfig b/arch/arm/configs/phytec-phycore-pxa270_defconfig deleted file mode 100644 index 370902c3c1..0000000000 --- a/arch/arm/configs/phytec-phycore-pxa270_defconfig +++ /dev/null @@ -1,60 +0,0 @@ -CONFIG_ARCH_PXA=y -CONFIG_ARCH_PXA27X=y -CONFIG_MACH_PCM027=y -CONFIG_AEABI=y -CONFIG_ARM_OPTIMZED_STRING_FUNCTIONS=y -CONFIG_ARM_UNWIND=y -CONFIG_MMU=y -CONFIG_MALLOC_SIZE=0x1000000 -CONFIG_MALLOC_TLSF=y -CONFIG_KALLSYMS=y -CONFIG_HUSH_FANCY_PROMPT=y -CONFIG_CMDLINE_EDITING=y -CONFIG_AUTO_COMPLETE=y -CONFIG_BOOTM_SHOW_TYPE=y -CONFIG_BOOTM_VERBOSE=y -CONFIG_BOOTM_INITRD=y -CONFIG_BOOTM_OFTREE=y -CONFIG_BOOTM_OFTREE_UIMAGE=y -CONFIG_PARTITION=y -CONFIG_DEFAULT_ENVIRONMENT_GENERIC_NEW=y -CONFIG_DEFAULT_ENVIRONMENT_PATH="arch/arm/boards/phytec-phycore-pxa270/env" -CONFIG_LONGHELP=y -CONFIG_CMD_IOMEM=y -CONFIG_CMD_MEMINFO=y -# CONFIG_CMD_BOOTU is not set -CONFIG_CMD_GO=y -CONFIG_CMD_RESET=y -CONFIG_CMD_UIMAGE=y -CONFIG_CMD_PARTITION=y -CONFIG_CMD_EXPORT=y -CONFIG_CMD_PRINTENV=y -CONFIG_CMD_MAGICVAR=y -CONFIG_CMD_MAGICVAR_HELP=y -CONFIG_CMD_SAVEENV=y -CONFIG_CMD_UNCOMPRESS=y -CONFIG_CMD_SLEEP=y -CONFIG_CMD_DHCP=y -CONFIG_CMD_PING=y -CONFIG_CMD_TFTP=y -CONFIG_CMD_ECHO_E=y -CONFIG_CMD_EDIT=y -CONFIG_CMD_SPLASH=y -CONFIG_CMD_READLINE=y -CONFIG_CMD_TIMEOUT=y -CONFIG_CMD_CRC=y -CONFIG_CMD_CRC_CMP=y -CONFIG_CMD_FLASH=y -CONFIG_CMD_GPIO=y -CONFIG_CMD_OFTREE=y -CONFIG_CMD_TIME=y -CONFIG_NET=y -CONFIG_DRIVER_SERIAL_PXA=y -CONFIG_DRIVER_NET_SMC91111=y -# CONFIG_SPI is not set -CONFIG_MTD=y -CONFIG_DRIVER_CFI=y -CONFIG_VIDEO=y -CONFIG_DRIVER_VIDEO_PXA=y -CONFIG_FS_TFTP=y -CONFIG_LZO_DECOMPRESS=y diff --git a/arch/arm/configs/zylonite310_defconfig b/arch/arm/configs/zylonite310_defconfig deleted file mode 100644 index cdbd135081..0000000000 --- a/arch/arm/configs/zylonite310_defconfig +++ /dev/null @@ -1,104 +0,0 @@ -CONFIG_ARCH_PXA=y -CONFIG_ARCH_PXA3XX=y -CONFIG_AEABI=y -CONFIG_ARM_BOARD_APPEND_ATAG=y -CONFIG_ARM_OPTIMZED_STRING_FUNCTIONS=y -CONFIG_ARM_UNWIND=y -# CONFIG_BANNER is not set -CONFIG_MMU=y -CONFIG_BAREBOX_MAX_IMAGE_SIZE=0x100000 -CONFIG_BAREBOX_MAX_BARE_INIT_SIZE=0x80000 -CONFIG_MALLOC_SIZE=0x800000 -CONFIG_EXPERIMENTAL=y -CONFIG_MODULES=y -CONFIG_KALLSYMS=y -CONFIG_PROMPT="zylonite-barebox:" -CONFIG_HUSH_FANCY_PROMPT=y -CONFIG_CMDLINE_EDITING=y -CONFIG_AUTO_COMPLETE=y -CONFIG_MENU=y -CONFIG_BOOTM_SHOW_TYPE=y -CONFIG_BOOTM_VERBOSE=y -CONFIG_BOOTM_INITRD=y -CONFIG_BOOTM_OFTREE=y -CONFIG_CONSOLE_ACTIVATE_ALL=y -CONFIG_DEFAULT_ENVIRONMENT_GENERIC_NEW=y -CONFIG_DEFAULT_ENVIRONMENT_PATH="arch/arm/boards/zylonite/env" -CONFIG_RESET_SOURCE=y -CONFIG_DEFAULT_LOGLEVEL=8 -CONFIG_CMD_DMESG=y -CONFIG_LONGHELP=y -CONFIG_CMD_IOMEM=y -CONFIG_CMD_MEMINFO=y -CONFIG_CMD_GO=y -CONFIG_CMD_LOADB=y -CONFIG_CMD_LOADS=y -CONFIG_CMD_LOADY=y -CONFIG_CMD_RESET=y -CONFIG_CMD_SAVES=y -CONFIG_CMD_PARTITION=y -CONFIG_CMD_UBIFORMAT=y -CONFIG_CMD_EXPORT=y -CONFIG_CMD_LOADENV=y -CONFIG_CMD_PRINTENV=y -CONFIG_CMD_SAVEENV=y -CONFIG_CMD_CMP=y -CONFIG_CMD_FILETYPE=y -CONFIG_CMD_LN=y -CONFIG_CMD_UNCOMPRESS=y -CONFIG_CMD_LET=y -CONFIG_CMD_MSLEEP=y -CONFIG_CMD_SLEEP=y -CONFIG_CMD_DHCP=y -CONFIG_CMD_MIITOOL=y -CONFIG_CMD_PING=y -CONFIG_CMD_TFTP=y -CONFIG_CMD_ECHO_E=y -CONFIG_CMD_EDIT=y -CONFIG_CMD_LOGIN=y -CONFIG_CMD_MENU=y -CONFIG_CMD_MENU_MANAGEMENT=y -CONFIG_CMD_PASSWD=y -CONFIG_CMD_READLINE=y -CONFIG_CMD_TIMEOUT=y -CONFIG_CMD_CRC=y -CONFIG_CMD_CRC_CMP=y -CONFIG_CMD_MEMTEST=y -CONFIG_CMD_MM=y -CONFIG_CMD_DETECT=y -CONFIG_CMD_FLASH=y -CONFIG_CMD_GPIO=y -CONFIG_CMD_POWEROFF=y -CONFIG_CMD_2048=y -CONFIG_CMD_LSMOD=y -CONFIG_CMD_OF_NODE=y -CONFIG_CMD_OF_PROPERTY=y -CONFIG_CMD_OFTREE=y -CONFIG_CMD_TIME=y -CONFIG_NET=y -CONFIG_NET_NETCONSOLE=y -CONFIG_OFDEVICE=y -CONFIG_OF_BAREBOX_DRIVERS=y -CONFIG_DRIVER_SERIAL_PXA=y -CONFIG_DRIVER_NET_SMC91111=y -# CONFIG_SPI is not set -CONFIG_MTD=y -CONFIG_NAND=y -CONFIG_NAND_MRVL_NFC=y -CONFIG_MTD_UBI=y -CONFIG_MCI=y -CONFIG_KEYBOARD_GPIO=y -CONFIG_PWM=y -# CONFIG_PINCTRL is not set -CONFIG_FS_CRAMFS=y -CONFIG_FS_EXT4=y -CONFIG_FS_TFTP=y -CONFIG_FS_NFS=y -CONFIG_FS_FAT=y -CONFIG_FS_FAT_WRITE=y -CONFIG_FS_FAT_LFN=y -CONFIG_FS_UBIFS=y -CONFIG_FS_UBIFS_COMPRESSION_LZO=y -CONFIG_FS_UBIFS_COMPRESSION_ZLIB=y -CONFIG_BZLIB=y -CONFIG_DIGEST_SHA256_GENERIC=y diff --git a/arch/arm/include/asm/mach-types.h b/arch/arm/include/asm/mach-types.h index 3b902aa021..259dc9568a 100644 --- a/arch/arm/include/asm/mach-types.h +++ b/arch/arm/include/asm/mach-types.h @@ -77,18 +77,6 @@ extern unsigned int __machine_arch_type; #define MACH_TYPE_PCAAXS1 4526 #define MACH_TYPE_PFLA03 4575 -#ifdef CONFIG_ARCH_LUBBOCK -# ifdef machine_arch_type -# undef machine_arch_type -# define machine_arch_type __machine_arch_type -# else -# define machine_arch_type MACH_TYPE_LUBBOCK -# endif -# define machine_is_lubbock() (machine_arch_type == MACH_TYPE_LUBBOCK) -#else -# define machine_is_lubbock() (0) -#endif - #ifdef CONFIG_ARCH_VERSATILE_PB # ifdef machine_arch_type # undef machine_arch_type @@ -113,18 +101,6 @@ extern unsigned int __machine_arch_type; # define machine_is_csb337() (0) #endif -#ifdef CONFIG_MACH_MAINSTONE -# ifdef machine_arch_type -# undef machine_arch_type -# define machine_arch_type __machine_arch_type -# else -# define machine_arch_type MACH_TYPE_MAINSTONE -# endif -# define machine_is_mainstone() (machine_arch_type == MACH_TYPE_MAINSTONE) -#else -# define machine_is_mainstone() (0) -#endif - #ifdef CONFIG_MACH_NOMADIK # ifdef machine_arch_type # undef machine_arch_type @@ -161,18 +137,6 @@ extern unsigned int __machine_arch_type; # define machine_is_at91rm9200ek() (0) #endif -#ifdef CONFIG_MACH_PCM027 -# ifdef machine_arch_type -# undef machine_arch_type -# define machine_arch_type __machine_arch_type -# else -# define machine_arch_type MACH_TYPE_PCM027 -# endif -# define machine_is_pcm027() (machine_arch_type == MACH_TYPE_PCM027) -#else -# define machine_is_pcm027() (0) -#endif - #ifdef CONFIG_MACH_AT91SAM9261EK # ifdef machine_arch_type # undef machine_arch_type @@ -221,30 +185,6 @@ extern unsigned int __machine_arch_type; # define machine_is_at91sam9263ek() (0) #endif -#ifdef CONFIG_MACH_ZYLONITE -# ifdef machine_arch_type -# undef machine_arch_type -# define machine_arch_type __machine_arch_type -# else -# define machine_arch_type MACH_TYPE_ZYLONITE -# endif -# define machine_is_zylonite() (machine_arch_type == MACH_TYPE_ZYLONITE) -#else -# define machine_is_zylonite() (0) -#endif - -#ifdef CONFIG_MACH_MIOA701 -# ifdef machine_arch_type -# undef machine_arch_type -# define machine_arch_type __machine_arch_type -# else -# define machine_arch_type MACH_TYPE_MIOA701 -# endif -# define machine_is_mioa701() (machine_arch_type == MACH_TYPE_MIOA701) -#else -# define machine_is_mioa701() (0) -#endif - #ifdef CONFIG_MACH_PM9263 # ifdef machine_arch_type # undef machine_arch_type diff --git a/arch/arm/mach-pxa/Kconfig b/arch/arm/mach-pxa/Kconfig index a506c8e892..53becd51d4 100644 --- a/arch/arm/mach-pxa/Kconfig +++ b/arch/arm/mach-pxa/Kconfig @@ -2,14 +2,6 @@ if ARCH_PXA -config ARCH_TEXT_BASE - hex - default 0xa0000000 if MACH_MIOA701 - default 0xa3f00000 if MACH_PCM027 - default 0xa3d00000 if MACH_LUBBOCK - default 0xa3d00000 if MACH_MAINSTONE - default 0x83f00000 if MACH_ZYLONITE - # ---------------------------------------------------------- config ARCH_PXA2XX @@ -41,83 +33,4 @@ config ARCH_PXA3XX endchoice -# ---------------------------------------------------------- - -if ARCH_PXA25X - -choice - prompt "PXA25x Board Type" - bool - -config MACH_LUBBOCK - bool "Lubbock board" - select PWM - help - Say Y here if you are using a Lubbock board -endchoice - -endif - -# ---------------------------------------------------------- - -if ARCH_PXA27X - -choice - prompt "PXA27x Board Type" - bool - -config MACH_MAINSTONE - bool "Mainstone board" - select PWM - help - Say Y here if you are using a Mainstone board -config MACH_MIOA701 - bool "Mitac Mio A701" - select PWM - select POLLER - help - Say Y here if you are using a Mitac Mio A701 smartphone - -config MACH_PCM027 - bool "Phytec phyCORE-PXA270" - help - Say Y here if you are using a Phytec phyCORE PXA270 - board -endchoice - -if MACH_MIOA701 -config BCH_CONST_M - int - default 14 if MACH_MIOA701 -config BCH_CONST_T - int - default 4 if MACH_MIOA701 -endif - -endif - -# ---------------------------------------------------------- - -if ARCH_PXA3XX - -config MACH_ZYLONITE - bool - -choice - prompt "PXA3xx Board Type" - -config MACH_ZYLONITE_PXA310 - bool "Zylonite board based on a PXA310 pxa SoC" - help - Say Y here if you are using a Zylonite board, based - on a PXA31x SoC. - select ARCH_PXA310 - select MACH_ZYLONITE - -endchoice - -endif - -# ---------------------------------------------------------- - endif -- 2.39.2
