This devicetree is in kernel upstream now. We can drop the barebox version now.
Signed-off-by: Oleksij Rempel <[email protected]> --- arch/arm/dts/stm32mp151-mecio1.dts | 213 +---------------------------- 1 file changed, 2 insertions(+), 211 deletions(-) diff --git a/arch/arm/dts/stm32mp151-mecio1.dts b/arch/arm/dts/stm32mp151-mecio1.dts index 6b50bdd4eff2..124f3079f256 100644 --- a/arch/arm/dts/stm32mp151-mecio1.dts +++ b/arch/arm/dts/stm32mp151-mecio1.dts @@ -1,214 +1,5 @@ // SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) -/* - * Copyright (C) Protonic Holland - * Author: David Jander <[email protected]> - */ /dts-v1/; -#include "arm/st/stm32mp151.dtsi" -#include "arm/st/stm32mp15xc.dtsi" -#include "arm/st/stm32mp15-pinctrl.dtsi" -#include "arm/st/stm32mp15xxaa-pinctrl.dtsi" -#include <dt-bindings/gpio/gpio.h> -#include <dt-bindings/input/input.h> - -/ { - model = "Protonic MECIO1"; - compatible = "prt,mecio1", "st,stm32mp151"; - - chosen { - stdout-path = "serial0:1500000n8"; - }; - - aliases { - serial0 = &uart4; - ethernet0 = ðernet0; - }; - - v3v3: fixed-regulator-v3v3 { - compatible = "regulator-fixed"; - regulator-name = "v3v3"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - }; - - v5v: fixed-regulator-v5v { - compatible = "regulator-fixed"; - regulator-name = "v5v"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - regulator-always-on; - }; - - led { - compatible = "gpio-leds"; - - led-0 { - label = "debug:red"; - gpios = <&gpioa 13 GPIO_ACTIVE_HIGH>; - }; - - led-1 { - label = "debug:green"; - gpios = <&gpioa 14 GPIO_ACTIVE_HIGH>; - linux,default-trigger = "heartbeat"; - }; - }; -}; - -&clk_hse { - clock-frequency = <25000000>; -}; - -&clk_lse { - status = "disabled"; -}; - -&qspi { - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&qspi_clk_pins_a - &qspi_bk1_pins_a - &qspi_cs1_pins_a>; - pinctrl-1 = <&qspi_clk_sleep_pins_a - &qspi_bk1_sleep_pins_a - &qspi_cs1_sleep_pins_a>; - status = "okay"; - - flash@0 { - compatible = "spi-nor"; - reg = <0>; - spi-rx-bus-width = <4>; - spi-max-frequency = <104000000>; - #address-cells = <1>; - #size-cells = <1>; - }; -}; - -&qspi_bk1_pins_a { - pins1 { - bias-pull-up; - drive-push-pull; - slew-rate = <1>; - }; -}; - -ðernet0 { - status = "okay"; - pinctrl-0 = <ðernet0_rgmii_pins_x>; - pinctrl-1 = <ðernet0_rgmii_sleep_pins_x>; - pinctrl-names = "default", "sleep"; - phy-mode = "rgmii-id"; - phy-handle = <&phy0>; - assigned-clocks = <&rcc ETHCK_K>, <&rcc PLL3_Q>; - assigned-clock-parents = <&rcc PLL3_Q>; - assigned-clock-rates = <125000000>; /* Clock PLL4 to 750Mhz in ATF/U-Boot */ - st,eth-clk-sel; - - mdio { - #address-cells = <1>; - #size-cells = <0>; - compatible = "snps,dwmac-mdio"; - - phy0: ethernet-phy@8 { - reg = <8>; - interrupts-extended = <&gpiog 7 IRQ_TYPE_LEVEL_LOW>; - reset-gpios = <&gpiog 10 GPIO_ACTIVE_LOW>; - reset-assert-us = <10>; - reset-deassert-us = <35>; - }; - }; -}; - -&usbotg_hs { - dr_mode = "host"; - pinctrl-0 = <&usbotg_hs_pins_a>; - pinctrl-names = "default"; - phys = <&usbphyc_port1 0>; - phy-names = "usb2-phy"; - vbus-supply = <&v5v>; - status = "okay"; -}; - -&usbphyc { - status = "okay"; -}; - -&usbphyc_port1 { - phy-supply = <&v3v3>; -}; - -&uart4 { - pinctrl-names = "default", "sleep", "idle"; - pinctrl-0 = <&uart4_pins_a>; - pinctrl-1 = <&uart4_sleep_pins_a>; - pinctrl-2 = <&uart4_idle_pins_a>; - /delete-property/dmas; - /delete-property/dma-names; - status = "okay"; -}; - -&uart4_pins_a { - pins1 { - pinmux = <STM32_PINMUX('B', 9, AF8)>; /* UART4_TX */ - bias-disable; - drive-push-pull; - slew-rate = <0>; - }; - pins2 { - pinmux = <STM32_PINMUX('B', 2, AF8)>; /* UART4_RX */ - bias-pull-up; - }; -}; - -&pinctrl { - ethernet0_rgmii_pins_x: rgmii-0 { - pins1 { - pinmux = <STM32_PINMUX('G', 5, AF11)>, /* ETH_RGMII_CLK125 */ - <STM32_PINMUX('G', 4, AF11)>, /* ETH_RGMII_GTX_CLK */ - <STM32_PINMUX('B', 12, AF11)>, /* ETH_RGMII_TXD0 */ - <STM32_PINMUX('B', 13, AF11)>, /* ETH_RGMII_TXD1 */ - <STM32_PINMUX('C', 2, AF11)>, /* ETH_RGMII_TXD2 */ - <STM32_PINMUX('B', 8, AF11)>, /* ETH_RGMII_TXD3 */ - <STM32_PINMUX('B', 11, AF11)>, /* ETH_RGMII_TX_CTL */ - <STM32_PINMUX('C', 1, AF11)>; /* ETH_MDC */ - bias-disable; - drive-push-pull; - slew-rate = <3>; - }; - pins2 { - pinmux = <STM32_PINMUX('A', 2, AF11)>; /* ETH_MDIO */ - bias-disable; - drive-push-pull; - slew-rate = <0>; - }; - pins3 { - pinmux = <STM32_PINMUX('C', 4, AF11)>, /* ETH_RGMII_RXD0 */ - <STM32_PINMUX('C', 5, AF11)>, /* ETH_RGMII_RXD1 */ - <STM32_PINMUX('H', 6, AF11)>, /* ETH_RGMII_RXD2 */ - <STM32_PINMUX('H', 7, AF11)>, /* ETH_RGMII_RXD3 */ - <STM32_PINMUX('A', 1, AF11)>, /* ETH_RGMII_RX_CLK */ - <STM32_PINMUX('A', 7, AF11)>; /* ETH_RGMII_RX_CTL */ - bias-disable; - }; - }; - - ethernet0_rgmii_sleep_pins_x: rgmii-sleep-0 { - pins1 { - pinmux = <STM32_PINMUX('G', 5, ANALOG)>, /* ETH_RGMII_CLK125 */ - <STM32_PINMUX('G', 4, ANALOG)>, /* ETH_RGMII_GTX_CLK */ - <STM32_PINMUX('B', 12, ANALOG)>, /* ETH_RGMII_TXD0 */ - <STM32_PINMUX('B', 13, ANALOG)>, /* ETH_RGMII_TXD1 */ - <STM32_PINMUX('C', 2, ANALOG)>, /* ETH_RGMII_TXD2 */ - <STM32_PINMUX('B', 8, ANALOG)>, /* ETH_RGMII_TXD3 */ - <STM32_PINMUX('B', 11, ANALOG)>, /* ETH_RGMII_TX_CTL */ - <STM32_PINMUX('A', 2, ANALOG)>, /* ETH_MDIO */ - <STM32_PINMUX('C', 1, ANALOG)>, /* ETH_MDC */ - <STM32_PINMUX('C', 4, ANALOG)>, /* ETH_RGMII_RXD0 */ - <STM32_PINMUX('C', 5, ANALOG)>, /* ETH_RGMII_RXD1 */ - <STM32_PINMUX('H', 6, ANALOG)>, /* ETH_RGMII_RXD2 */ - <STM32_PINMUX('H', 7, ANALOG)>, /* ETH_RGMII_RXD3 */ - <STM32_PINMUX('A', 1, ANALOG)>, /* ETH_RGMII_RX_CLK */ - <STM32_PINMUX('A', 7, ANALOG)>; /* ETH_RGMII_RX_CTL */ - }; - }; -}; +#include <arm/st/stm32mp151c-mecio1r0.dts> +#include "stm32mp151.dtsi" -- 2.39.5
