Hi, I have a Virtual Tape Library based on HPE Store Once. The tapes have their barcodes, but I see non-fatal errors - which I would like to get rid of - when starting reading and releasing tapes. See some examples:
==== 2023-11-06 07:00:02 mt1it-bkpmgr01-dir JobId 983: Using Device "bareos01-vtl-drv-0" to write. 2023-11-06 07:00:02 mt1it-bkpstg01-fd JobId 983: Connected Storage daemon at mt1it-bkpstg01.:9103, encryption: TLS_AES_256_GCM_SHA384 TLSv1.3 2023-11-06 07:00:02 mt1it-bkpstg01-fd JobId 983: Encryption: TLS_AES_256_GCM_SHA384 TLSv1.3 2023-11-06 07:00:02 mt1it-bkpstg01-fd JobId 983: Extended attribute support is enabled 2023-11-06 07:00:02 mt1it-bkpstg01-sd JobId 983: 3307 Issuing autochanger "unload slot 75, drive 0" command. 2023-11-06 07:00:02 mt1it-bkpstg01-fd JobId 983: ACL support is enabled 2023-11-06 07:00:03 mt1it-bkpstg01-sd JobId 983: 3304 Issuing autochanger "load slot 19, drive 0" command. 2023-11-06 07:00:03 mt1it-bkpstg01-sd JobId 983: 3305 Autochanger "load slot 19, drive 0", status is OK. 2023-11-06 07:00:04 *mt1it-bkpstg01-sd JobId 983: Error: stored/block.cc:1019 Read zero bytes at 187:0 on device "bareos01-vtl-drv-0" (/dev/tape/by-id/scsi-351402ec009730a4a-nst).* 2023-11-06 07:00:05 mt1it-bkpstg01-sd JobId 983: Volume "8FH3A89O" previously written, moving to end of data. ==== ==== 2023-11-06 05:00:02 mt1it-bkpmgr01-dir JobId 982: Using Device "bareos01-vtl-drv-2" to write. 2023-11-06 05:00:02 mt1it-bkpstg01-fd JobId 982: Connected Storage daemon at mt1it-bkpstg01:9103, encryption: TLS_AES_256_GCM_SHA384 TLSv1.3 2023-11-06 05:00:02 mt1it-bkpstg01-fd JobId 982: Encryption: TLS_AES_256_GCM_SHA384 TLSv1.3 2023-11-06 05:00:02 mt1it-bkpstg01-fd JobId 982: Extended attribute support is enabled 2023-11-06 05:00:02 mt1it-bkpstg01-fd JobId 982: ACL support is enabled 2023-11-06 05:00:02 mt1it-bkpstg01-sd JobId 982: 3307 Issuing autochanger "unload slot 81, drive 1" command. 2023-11-06 05:00:03 mt1it-bkpstg01-sd JobId 982: 3304 Issuing autochanger "load slot 55, drive 2" command. 2023-11-06 05:00:03 mt1it-bkpstg01-sd JobId 982: 3305 Autochanger "load slot 55, drive 2", status is OK. *2023-11-06 05:00:03mt1it-bkpstg01-sd JobId 982: Error: Attempt to read past end of tape or file.*2023-11-06 05:00:04 mt1it-bkpstg01-sd JobId 982: Volume "8FH3A8AO" previously written, moving to end of data. 2023-11-06 05:00:04 mt1it-bkpstg01-sd JobId 982: Ready to append to end of Volume "8FH3A8AO" at file=38. ==== === 2023-11-05 12:00:02 | mt1it-bkpmgr01-dir JobId 958: Using Device "bareos01-vtl-drv-4" to write. 2023-11-05 12:00:02 | mt1it-bkpstg01-fd JobId 958: Connected Storage daemon at mt1it-bkpstg01:9103, encryption: TLS_AES_256_GCM_SHA384 TLSv1.3+ 2023-11-05 12:00:02 | mt1it-bkpstg01-fd JobId 958: Encryption: TLS_AES_256_GCM_SHA384 TLSv1.3 2023-11-05 12:00:02 | mt1it-bkpstg01-fd JobId 958: Extended attribute support is enabled 2023-11-05 12:00:02 | mt1it-bkpstg01-fd JobId 958: ACL support is enabled 2023-11-05 12:00:03 | mt1it-bkpstg01-sd JobId 958: 3304 Issuing autochanger "load slot 75, drive 4" command. 2023-11-05 12:00:03 | mt1it-bkpstg01-sd JobId 958: 3305 Autochanger "load slot 75, drive 4", status is OK. * 2023-11-05 12:00:04 | mt1it-bkpstg01-sd JobId 958: Error:* 2023-11-05 12:00:05 | mt1it-bkpstg01-sd JobId 958: Volume "8FH3A8B8" previously written, moving to end of data. 2023-11-05 12:00:05 | mt1it-bkpstg01-sd JobId 958: Ready to append to end of Volume "8FH3A8B8" at file=164. 2023-11-05 13:16:47 | mt1it-bkpstg01-sd JobId 958: Releasing device "bareos01-vtl-drv-4" (/dev/tape/by-id/scsi-351402ec009730a6e-nst). 2023-11-05 13:16:48 | mt1it-bkpstg01-sd JobId 958: Elapsed time=01:16:43, Transfer rate=124.2 M Bytes/second === Here is the configuration of the pool/device from the Director: === Pool { Name = MT1-MSSQLPROD-POOL Pool Type = Backup Recycle = yes AutoPrune = yes Volume Retention = 3650 days Maximum Volumes = 30 Storage = mt1it-bkpstg01-sd:bareos01-vtl } Storage { Name = mt1it-bkpstg01-sd:bareos01-vtl Address = mt1it-bkpstg01 Password = "xxxx" Auto Changer = yes Device = bareos01-vtl Media Type = LTO Allow Compression = no Maximum Concurrent Jobs = 40 # TLS Configuration [...] } === Here is the configuration of one of the drives: === Autochanger { Name = "bareos01-vtl" Changer Device = /dev/tape/by-id/scsi-351402ec009730138 Device = bareos01-vtl-drv-0 Device = bareos01-vtl-drv-1 [...] Changer Command = "/usr/lib/bareos/scripts/mtx-changer %c %o %S %a %d" } Device { Name = "bareos01-vtl-drv-0" DeviceType = tape DriveIndex = 0 ArchiveDevice = /dev/tape/by-id/scsi-351402ec009730a4a-nst MediaType = LTO Check Labels = yes Label Media = yes Maximum Network Buffer Size = 65536 AutoChanger = yes AutomaticMount = yes MaximumFileSize = 25GB Maximum block size = 1048576 Maximum Concurrent Jobs = 6 Always Open = no Auto Inflate = out } === Any tip to get rid of these errors? Thank you. -- You received this message because you are subscribed to the Google Groups "bareos-users" group. To unsubscribe from this group and stop receiving emails from it, send an email to bareos-users+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/bareos-users/4488c3ab-97cb-4cef-8947-cb9a59e3fe12n%40googlegroups.com.