Hello,
I use WPA with wpa_supplicant v0.5.5.
ps -def | grep wpa
root 5975 1 0 19:10 ?
00:00:00 /sbin/wpa_supplicant -Dwext -c/etc/wpa_supplicant/wpa_supplicant.conf
-W -B -ieth1 -P/var/run/wpa_supplicant-eth1.pid
root 5986 1 0 19:10 ?
00:00:00 /bin/wpa_cli -a/etc/wpa_supplicant/wpa_cli.sh
-p/var/run/wpa_supplicant -ieth1 -P/var/run/wpa_cli-eth1.pid -B
root 6638 5986 0 19:46 ?
00:00:00 /bin/sh /etc/wpa_supplicant/wpa_cli.sh eth1 CONNECTED
root 7030 7029 0 19:46 ? 00:00:00 /bin/wpa_cli -ieth1 status
lspci:
06:02.0 Network controller: Broadcom Corporation BCM4318 [AirForce One 54g]
802.11g Wireless LAN Controller (rev 02)
Subsystem: AMBIT Microsystem Corp. Aspire 3022WLMi, 5024WLMi
Flags: bus master, fast devsel, latency 64, IRQ 21
Memory at c0304000 (32-bit, non-prefetchable) [size=8K]
another dmeg output with the beginning:
ACPI: PCI Interrupt 0000:06:02.0[A] -> GSI 21 (level, low) -> IRQ 21
bcm43xx: Chip ID 0x4318, rev 0x2
bcm43xx: Number of cores: 4
bcm43xx: Core 0: ID 0x800, rev 0xd, vendor 0x4243, enabled
bcm43xx: Core 1: ID 0x812, rev 0x9, vendor 0x4243, enabled
bcm43xx: Core 2: ID 0x804, rev 0xc, vendor 0x4243, enabled
bcm43xx: Core 3: ID 0x80d, rev 0x7, vendor 0x4243, enabled
bcm43xx: PHY connected
bcm43xx: Detected PHY: Version: 3, Type 2, Revision 7
bcm43xx: Detected Radio: ID: 8205017f (Manuf: 17f Ver: 2050 Rev: 8)
bcm43xx: Radio turned off
bcm43xx: Radio turned off
bcm43xx: PHY connected
bcm43xx: Microcode rev 0x123, pl 0x21 (2005-01-22 19:48:06)
bcm43xx: Radio turned on
bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at:
drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1496:bcm43xx_find_lopair()
bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at:
drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1496:bcm43xx_find_lopair()
bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at:
drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1496:bcm43xx_find_lopair()
bcm43xx: Chip initialized
bcm43xx: 32-bit DMA initialized
bcm43xx: Keys cleared
bcm43xx: Selected 802.11 core (phytype 2)
bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at:
drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1496:bcm43xx_find_lopair()
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Associate: failed to initiate scan. Is device up?
ADDRCONF(NETDEV_UP): eth1: link is not ready
SoftMAC: empty ratesinfo?
SoftMAC: empty ratesinfo?
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
SoftMAC: Scanning finished
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
SoftMAC: Unable to find matching network after scan!
SoftMAC: Scanning finished
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
SoftMAC: Scanning finished
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
SoftMAC: Scanning finished
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
SoftMAC: Scanning finished
SoftMAC: Unable to find matching network after scan!
SoftMAC: generic IE set to dd160050f20101000050f20201000050f20201000050f202
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
SoftMAC: Queueing Authentication Request to 00:13:10:2f:98:3e
SoftMAC: Cannot associate without being authenticated, requested
authentication
SoftMAC: Sent Authentication Request to 00:13:10:2f:98:3e.
printk: 2 messages suppressed.
SoftMAC: Open Authentication completed with 00:13:10:2f:98:3e
SoftMAC: sent association request!
SoftMAC: Scanning finished
SoftMAC: sent association request!
SoftMAC: associated!
ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
bcm43xx: set security called, .active_key = 0, .level = 2, .enabled =
1, .encrypt = 1
bcm43xx: set security called, .enabled = 1, .encrypt = 1
SoftMAC: Authentication response received from 00:0f:b5:05:4b:b8 but no queue
item exists.
SoftMAC: Authentication response received from 00:13:10:2f:98:3e but no queue
item exists.
Other information needed?
Kind regards,
Christian Hoffmann
On Sunday 24 September 2006 19:30, Michael Buesch wrote:
> On Sunday 24 September 2006 19:06, Christian wrote:
> > Hi,
> >
> > maybe I was a bit too optimistic about 4318 working now with Larry's big
> > 2.6.18 patch. After some reboots, it seems that my card is reconnecting
> > all the time. I turned on softmac debugging to see more.
> >
> > Here's some dmesg output ...
>
> Can you provide more information on how to reproduce this?
> What's your setup? Using WEP? Using WPA? using wpa_supplicant?
>
> > Chris
> > ...
> >
> > ...
> > SoftMAC: Sent Authentication Request to 00:13:10:2f:98:3e.
> > SoftMAC: generic IE set to
> > dd160050f20101000050f20201000050f20201000050f202 SoftMAC: Already
> > associating or associated to 00:13:10:2f:98:3e
> > SoftMAC: sent association request!
> > SoftMAC: associated!
> > bcm43xx: set security called, .active_key = 0, .level = 2, .enabled =
> > 1, .encrypt = 1
> > bcm43xx: set security called, .enabled = 1, .encrypt = 1
> > printk: 2 messages suppressed.
> > SoftMAC: Authentication response received from 00:0f:b5:05:4b:b8 but no
> > queue item exists.
> > SoftMAC: Associate: Scanning for networks first.
> > SoftMAC: Start scanning with channel: 1
> > SoftMAC: Scanning 14 channels
> > bcm43xx: set security called, .enabled = 0, .encrypt = 0
> > bcm43xx: set security called, .enabled = 0, .encrypt = 0
> > bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
> > bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
> > bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
> > SoftMAC: Scanning finished
> > SoftMAC: Queueing Authentication Request to 00:13:10:2f:98:3e
> > SoftMAC: Cannot associate without being authenticated, requested
> > authentication
> > SoftMAC: Sent Authentication Request to 00:13:10:2f:98:3e.
> > SoftMAC: generic IE set to
> > dd160050f20101000050f20201000050f20201000050f202 SoftMAC: Already
> > associating or associated to 00:13:10:2f:98:3e
> > printk: 1 messages suppressed.
> > SoftMAC: Open Authentication completed with 00:13:10:2f:98:3e
> > SoftMAC: sent association request!
> > SoftMAC: associated!
> > bcm43xx: set security called, .active_key = 0, .level = 2, .enabled =
> > 1, .encrypt = 1
> > bcm43xx: set security called, .enabled = 1, .encrypt = 1
> > SoftMAC: Authentication response received from 00:0f:b5:05:4b:b8 but no
> > queue item exists.
> > SoftMAC: Associate: Scanning for networks first.
> > SoftMAC: Start scanning with channel: 1
> > SoftMAC: Scanning 14 channels
> > bcm43xx: set security called, .enabled = 0, .encrypt = 0
> > bcm43xx: set security called, .enabled = 0, .encrypt = 0
> > bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
> > bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
> > bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
> > SoftMAC: Scanning finished
> > SoftMAC: Queueing Authentication Request to 00:13:10:2f:98:3e
> > SoftMAC: Cannot associate without being authenticated, requested
> > authentication
> > SoftMAC: Sent Authentication Request to 00:13:10:2f:98:3e.
> > SoftMAC: generic IE set to
> > dd160050f20101000050f20201000050f20201000050f202 SoftMAC: Already
> > associating or associated to 00:13:10:2f:98:3e
> > printk: 1 messages suppressed.
> > SoftMAC: Open Authentication completed with 00:13:10:2f:98:3e
> > SoftMAC: sent association request!
> > SoftMAC: associated!
> > bcm43xx: set security called, .active_key = 0, .level = 2, .enabled =
> > 1, .encrypt = 1
> > bcm43xx: set security called, .enabled = 1, .encrypt = 1
> > SoftMAC: Associate: Scanning for networks first.
> > SoftMAC: Start scanning with channel: 1
> > SoftMAC: Scanning 14 channels
> > bcm43xx: set security called, .enabled = 0, .encrypt = 0
> > bcm43xx: set security called, .enabled = 0, .encrypt = 0
> > bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
> > bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
> > bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
> > SoftMAC: Scanning finished
> > SoftMAC: Queueing Authentication Request to 00:13:10:2f:98:3e
> > SoftMAC: Cannot associate without being authenticated, requested
> > authentication
> > SoftMAC: Sent Authentication Request to 00:13:10:2f:98:3e.
> > SoftMAC: generic IE set to
> > dd160050f20101000050f20201000050f20201000050f202 SoftMAC: Already
> > associating or associated to 00:13:10:2f:98:3e
> > printk: 2 messages suppressed.
> > SoftMAC: Open Authentication completed with 00:13:10:2f:98:3e
> > SoftMAC: sent association request!
> > SoftMAC: associated!
> > bcm43xx: set security called, .active_key = 0, .level = 2, .enabled =
> > 1, .encrypt = 1
> > bcm43xx: set security called, .enabled = 1, .encrypt = 1
> > SoftMAC: Authentication response received from 00:0f:b5:05:4b:b8 but no
> > queue item exists.
> > SoftMAC: Associate: Scanning for networks first.
> > SoftMAC: Start scanning with channel: 1
> > SoftMAC: Scanning 14 channels
> > bcm43xx: set security called, .enabled = 0, .encrypt = 0
> > bcm43xx: set security called, .enabled = 0, .encrypt = 0
> > bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
> > bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
> > bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
> > SoftMAC: Scanning finished
> > SoftMAC: Queueing Authentication Request to 00:13:10:2f:98:3e
> > SoftMAC: Cannot associate without being authenticated, requested
> > authentication
> > SoftMAC: Sent Authentication Request to 00:13:10:2f:98:3e.
> > SoftMAC: generic IE set to
> > dd160050f20101000050f20201000050f20201000050f202 SoftMAC: Already
> > associating or associated to 00:13:10:2f:98:3e
> > printk: 1 messages suppressed.
> > SoftMAC: Open Authentication completed with 00:13:10:2f:98:3e
> > SoftMAC: sent association request!
> > SoftMAC: associated!
> > bcm43xx: set security called, .active_key = 0, .level = 2, .enabled =
> > 1, .encrypt = 1
> > bcm43xx: set security called, .enabled = 1, .encrypt = 1
> > SoftMAC: Associate: Scanning for networks first.
> > SoftMAC: Start scanning with channel: 1
> > SoftMAC: Scanning 14 channels
> > bcm43xx: set security called, .enabled = 0, .encrypt = 0
> > bcm43xx: set security called, .enabled = 0, .encrypt = 0
> > bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
> > bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
> > bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
> > SoftMAC: Scanning finished
> > SoftMAC: Queueing Authentication Request to 00:13:10:2f:98:3e
> > SoftMAC: Cannot associate without being authenticated, requested
> > authentication
> > SoftMAC: Sent Authentication Request to 00:13:10:2f:98:3e.
> > SoftMAC: generic IE set to
> > dd160050f20101000050f20201000050f20201000050f202 SoftMAC: Already
> > associating or associated to 00:13:10:2f:98:3e
> > printk: 2 messages suppressed.
> > SoftMAC: Open Authentication completed with 00:13:10:2f:98:3e
> > SoftMAC: sent association request!
> > SoftMAC: associated!
> > bcm43xx: set security called, .active_key = 0, .level = 2, .enabled =
> > 1, .encrypt = 1
> > bcm43xx: set security called, .enabled = 1, .encrypt = 1
> > SoftMAC: Authentication response received from 00:0f:b5:05:4b:b8 but no
> > queue item exists.
> > SoftMAC: Associate: Scanning for networks first.
> > SoftMAC: Start scanning with channel: 1
> > SoftMAC: Scanning 14 channels
> > bcm43xx: set security called, .enabled = 0, .encrypt = 0
> > bcm43xx: set security called, .enabled = 0, .encrypt = 0
> > bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
> > bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
> > bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
> > SoftMAC: Scanning finished
> > SoftMAC: Queueing Authentication Request to 00:13:10:2f:98:3e
> > SoftMAC: Cannot associate without being authenticated, requested
> > authentication
> > SoftMAC: Sent Authentication Request to 00:13:10:2f:98:3e.
> > SoftMAC: generic IE set to
> > dd160050f20101000050f20201000050f20201000050f202 SoftMAC: Already
> > associating or associated to 00:13:10:2f:98:3e
> > printk: 1 messages suppressed.
> > SoftMAC: Open Authentication completed with 00:13:10:2f:98:3e
> > SoftMAC: sent association request!
> > SoftMAC: associated!
> > bcm43xx: set security called, .active_key = 0, .level = 2, .enabled =
> > 1, .encrypt = 1
> > bcm43xx: set security called, .enabled = 1, .encrypt = 1
> > SoftMAC: Authentication response received from 00:0f:b5:05:4b:b8 but no
> > queue item exists.
> > SoftMAC: Associate: Scanning for networks first.
> > SoftMAC: Start scanning with channel: 1
> > SoftMAC: Scanning 14 channels
> > bcm43xx: set security called, .enabled = 0, .encrypt = 0
> > bcm43xx: set security called, .enabled = 0, .encrypt = 0
> > bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
> > bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
> > bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
> > SoftMAC: Scanning finished
> > SoftMAC: Queueing Authentication Request to 00:13:10:2f:98:3e
> > SoftMAC: Cannot associate without being authenticated, requested
> > authentication
> > SoftMAC: Sent Authentication Request to 00:13:10:2f:98:3e.
> > SoftMAC: generic IE set to
> > dd160050f20101000050f20201000050f20201000050f202 SoftMAC: Already
> > associating or associated to 00:13:10:2f:98:3e
> > printk: 1 messages suppressed.
> > SoftMAC: Open Authentication completed with 00:13:10:2f:98:3e
> > SoftMAC: sent association request!
> > SoftMAC: associated!
> > bcm43xx: set security called, .active_key = 0, .level = 2, .enabled =
> > 1, .encrypt = 1
> > bcm43xx: set security called, .enabled = 1, .encrypt = 1
> > SoftMAC: Associate: Scanning for networks first.
> > SoftMAC: Start scanning with channel: 1
> > SoftMAC: Scanning 14 channels
> > bcm43xx: set security called, .enabled = 0, .encrypt = 0
> > bcm43xx: set security called, .enabled = 0, .encrypt = 0
> > bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
> > bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
> > bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
> > SoftMAC: Scanning finished
> > SoftMAC: Queueing Authentication Request to 00:13:10:2f:98:3e
> > SoftMAC: Cannot associate without being authenticated, requested
> > authentication
> > SoftMAC: Sent Authentication Request to 00:13:10:2f:98:3e.
> > SoftMAC: generic IE set to
> > dd160050f20101000050f20201000050f20201000050f202 SoftMAC: Already
> > associating or associated to 00:13:10:2f:98:3e
> > printk: 2 messages suppressed.
> > SoftMAC: Open Authentication completed with 00:13:10:2f:98:3e
> > SoftMAC: sent association request!
> > SoftMAC: associated!
> > bcm43xx: set security called, .active_key = 0, .level = 2, .enabled =
> > 1, .encrypt = 1
> > bcm43xx: set security called, .enabled = 1, .encrypt = 1
> > SoftMAC: Authentication response received from 00:0f:b5:05:4b:b8 but no
> > queue item exists.
> > SoftMAC: Associate: Scanning for networks first.
> > SoftMAC: Start scanning with channel: 1
> > SoftMAC: Scanning 14 channels
> > bcm43xx: set security called, .enabled = 0, .encrypt = 0
> > bcm43xx: set security called, .enabled = 0, .encrypt = 0
> > bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
> > bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
> > bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
> > SoftMAC: Scanning finished
> > SoftMAC: Queueing Authentication Request to 00:13:10:2f:98:3e
> > SoftMAC: Cannot associate without being authenticated, requested
> > authentication
> > SoftMAC: Sent Authentication Request to 00:13:10:2f:98:3e.
> > printk: 1 messages suppressed.
> > SoftMAC: Open Authentication completed with 00:13:10:2f:98:3e
> > SoftMAC: sent association request!
> > SoftMAC: generic IE set to
> > dd160050f20101000050f20201000050f20201000050f202 SoftMAC: Already
> > associating or associated to 00:13:10:2f:98:3e
> > SoftMAC: associated!
> > bcm43xx: set security called, .active_key = 0, .level = 2, .enabled =
> > 1, .encrypt = 1
> > bcm43xx: set security called, .enabled = 1, .encrypt = 1
> > SoftMAC: Associate: Scanning for networks first.
> > SoftMAC: Start scanning with channel: 1
> > SoftMAC: Scanning 14 channels
> > bcm43xx: set security called, .enabled = 0, .encrypt = 0
> > bcm43xx: set security called, .enabled = 0, .encrypt = 0
> > bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
> > bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
> > bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
> > SoftMAC: Scanning finished
> > SoftMAC: Queueing Authentication Request to 00:13:10:2f:98:3e
> > SoftMAC: Cannot associate without being authenticated, requested
> > authentication
> > SoftMAC: Sent Authentication Request to 00:13:10:2f:98:3e.
> > SoftMAC: generic IE set to
> > dd160050f20101000050f20201000050f20201000050f202 SoftMAC: Already
> > associating or associated to 00:13:10:2f:98:3e
> > printk: 2 messages suppressed.
> > SoftMAC: Open Authentication completed with 00:13:10:2f:98:3e
> > SoftMAC: sent association request!
> > SoftMAC: associated!
> > bcm43xx: set security called, .active_key = 0, .level = 2, .enabled =
> > 1, .encrypt = 1
> > bcm43xx: set security called, .enabled = 1, .encrypt = 1
> > SoftMAC: Authentication response received from 00:0f:b5:05:4b:b8 but no
> > queue item exists.
> > SoftMAC: Associate: Scanning for networks first.
> > SoftMAC: Start scanning with channel: 1
> > SoftMAC: Scanning 14 channels
> > bcm43xx: set security called, .enabled = 0, .encrypt = 0
> > bcm43xx: set security called, .enabled = 0, .encrypt = 0
> > bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
> > bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
> > bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
> > SoftMAC: Scanning finished
> > SoftMAC: Queueing Authentication Request to 00:13:10:2f:98:3e
> > SoftMAC: Cannot associate without being authenticated, requested
> > authentication
> > SoftMAC: Sent Authentication Request to 00:13:10:2f:98:3e.
> > SoftMAC: generic IE set to
> > dd160050f20101000050f20201000050f20201000050f202 SoftMAC: Already
> > associating or associated to 00:13:10:2f:98:3e
> > printk: 1 messages suppressed.
> > SoftMAC: Open Authentication completed with 00:13:10:2f:98:3e
> > SoftMAC: sent association request!
> > SoftMAC: associated!
> > bcm43xx: set security called, .active_key = 0, .level = 2, .enabled =
> > 1, .encrypt = 1
> > bcm43xx: set security called, .enabled = 1, .encrypt = 1
> > SoftMAC: Authentication response received from 00:0f:b5:05:4b:b8 but no
> > queue item exists.
> > SoftMAC: Associate: Scanning for networks first.
> > SoftMAC: Start scanning with channel: 1
> > SoftMAC: Scanning 14 channels
> > bcm43xx: set security called, .enabled = 0, .encrypt = 0
> > bcm43xx: set security called, .enabled = 0, .encrypt = 0
> > bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
> > bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
> > bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
> > SoftMAC: Scanning finished
> > SoftMAC: Queueing Authentication Request to 00:13:10:2f:98:3e
> > SoftMAC: Cannot associate without being authenticated, requested
> > authentication
> > SoftMAC: Sent Authentication Request to 00:13:10:2f:98:3e.
> > SoftMAC: generic IE set to
> > dd160050f20101000050f20201000050f20201000050f202 SoftMAC: Already
> > associating or associated to 00:13:10:2f:98:3e
> > SoftMAC: sent association request!
> > SoftMAC: associated!
> > bcm43xx: set security called, .active_key = 0, .level = 2, .enabled =
> > 1, .encrypt = 1
> > bcm43xx: set security called, .enabled = 1, .encrypt = 1
> > printk: 2 messages suppressed.
> > SoftMAC: Authentication response received from 00:0f:b5:05:4b:b8 but no
> > queue item exists.
> > SoftMAC: Associate: Scanning for networks first.
> > SoftMAC: Start scanning with channel: 1
> > SoftMAC: Scanning 14 channels
> > bcm43xx: set security called, .enabled = 0, .encrypt = 0
> > bcm43xx: set security called, .enabled = 0, .encrypt = 0
> > bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
> > bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
> > bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
> > SoftMAC: Scanning finished
> > SoftMAC: Queueing Authentication Request to 00:13:10:2f:98:3e
> > SoftMAC: Cannot associate without being authenticated, requested
> > authentication
> > SoftMAC: Sent Authentication Request to 00:13:10:2f:98:3e.
> > SoftMAC: generic IE set to
> > dd160050f20101000050f20201000050f20201000050f202 SoftMAC: Already
> > associating or associated to 00:13:10:2f:98:3e
> > printk: 1 messages suppressed.
> > SoftMAC: Open Authentication completed with 00:13:10:2f:98:3e
> > SoftMAC: sent association request!
> > SoftMAC: associated!
> > bcm43xx: set security called, .active_key = 0, .level = 2, .enabled =
> > 1, .encrypt = 1
> > bcm43xx: set security called, .enabled = 1, .encrypt = 1
> > _______________________________________________
> > Bcm43xx-dev mailing list
> > [email protected]
> > https://lists.berlios.de/mailman/listinfo/bcm43xx-dev
_______________________________________________
Bcm43xx-dev mailing list
[email protected]
https://lists.berlios.de/mailman/listinfo/bcm43xx-dev
