Fernando Toledo wrote: > Hi i have a problem to see an Dlink ap900+ in my house (that have the > latest revision "B" firmware and basic ap configuration) > > i have a zd1211 usb dongle and my onboard 4311PCIE (the zydas dongle > connect fine, but not the 4311) > > wlan1 : zd1211rw > eth1: bcm43xx > > i can connect to another ap (Noganet vendor), but not here > > ntbkragnarok:/usr/src# iwlist wlan1 s > wlan1 Scan completed : > Cell 01 - Address: 00:80:C8:AC:AA:06 > ESSID:"docksud" > Protocol:IEEE 802.11b > Mode:Master > Channel:6 > Encryption key:off > Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 22 Mb/s > Quality=100/100 Signal level=82/100 > Extra: Last beacon: 180ms ago > > ntbkragnarok:/usr/src# iwlist eth1 s > eth1 No scan results > ntbkragnarok:/usr/src# > > ACPI: PCI Interrupt 0000:10:00.0[A] -> GSI 17 (level, low) -> IRQ 17 > PCI: Setting latency timer of device 0000:10:00.0 to 64 > bcm43xx: Chip ID 0x4311, rev 0x1 > bcm43xx: Number of cores: 4 > bcm43xx: Core 0: ID 0x800, rev 0x11, vendor 0x4243, enabled > bcm43xx: Core 1: ID 0x812, rev 0xa, vendor 0x4243, disabled > bcm43xx: Core 2: ID 0x817, rev 0x3, vendor 0x4243, disabled > bcm43xx: Core 3: ID 0x820, rev 0x1, vendor 0x4243, enabled > bcm43xx: PHY connected > bcm43xx: Detected PHY: Version: 4, Type 2, Revision 8 > bcm43xx: Detected Radio: ID: 2205017f (Manuf: 17f Ver: 2050 Rev: 2) > bcm43xx: Radio turned off > bcm43xx: Radio turned off > bcm43xx: PHY connected > bcm43xx: Microcode rev 0x127, pl 0xe (2005-04-18 02:36:27) > bcm43xx: Radio turned on > bcm43xx: Radio disabled by hardware > bcm43xx: Chip initialized > bcm43xx: 32-bit DMA initialized > bcm43xx: Keys cleared > bcm43xx: Selected 802.11 core (phytype 2) > bcm43xx: Radio hardware status changed to enabled > SoftMAC: Start scanning with channel: 1 > SoftMAC: Scanning 14 channels > SoftMAC: Scanning finished > SoftMAC: Start scanning with channel: 1 > SoftMAC: Scanning 14 channels > SoftMAC: Scanning finished > SoftMAC: Start scanning with channel: 1 > SoftMAC: Scanning 14 channels > SoftMAC: Scanning finished > > i test it on 2.6.19.2 (with the las two larry patches for 2.6.19.1) > these patch's was apply succesfully on 2.6.19.2 > ntbkragnarok:/usr/src# iwconfig > lo no wireless extensions. > > eth0 no wireless extensions. > > eth1 IEEE 802.11b/g ESSID:"docksud" Nickname:"Broadcom 4311" > Mode:Managed Frequency=2.484 GHz Access Point: Invalid > Bit Rate=1 Mb/s Tx-Power=18 dBm > RTS thr:off Fragment thr:off > Encryption key:off > Link Quality=0/100 Signal level=-256 dBm Noise level=-256 dBm > Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 > Tx excessive retries:0 Invalid misc:0 Missed beacon:0 > > wlan1 IEEE 802.11b/g ESSID:"docksud" Nickname:"zd1211" > Mode:Managed Frequency:2.437 GHz Access Point: > 00:80:C8:AC:AA:06 > Bit Rate=11 Mb/s > Encryption key:off > Link Quality=60/100 Signal level=24/100 > Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 > Tx excessive retries:0 Invalid misc:0 Missed beacon:0
I asked you once before for the output of ifconfig. We have no way to know if your interface is up or down. Larry _______________________________________________ Bcm43xx-dev mailing list [email protected] https://lists.berlios.de/mailman/listinfo/bcm43xx-dev
