On Thursday 25 January 2007 01:21, Peter Chubb wrote: > > Hi, > I tried your tree. It doesn't work too well with my bcm4306 > chip.
Known issues. Thanks for testing. > > I see not one but two interfaces created: eth1 and wlan0_rename. > > eth1 Link encap:UNSPEC HWaddr > 00-03-C9-53-89-50-30-3A-00-00-00-00-00-00-00-00 > BROADCAST MULTICAST MTU:1500 Metric:1 > RX packets:0 errors:0 dropped:0 overruns:0 frame:0 > TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:1000 > RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) > > wlan0_ren Link encap:Ethernet HWaddr 00:03:C9:53:89:50 > MULTICAST MTU:1500 Metric:1 > RX packets:0 errors:0 dropped:0 overruns:0 frame:0 > TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:0 > RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) > > > Dmesg output after "ifconfig wlan0_rename up" is: > > ACPI: PCI Interrupt 0000:02:03.0[A] -> Link [LNKB] -> GSI 5 (level, low) -> > IRQ 5 > ssb: Sonics Silicon Backplane found on PCI device 0000:02:03.0 > ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x04, vendor 0x4243) > ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x05, vendor 0x4243) > ssb: Core 2 found: PCMCIA (cc 0x80D, rev 0x02, vendor 0x4243) > ssb: Core 3 found: V90 (cc 0x807, rev 0x02, vendor 0x4243) > ssb: Core 4 found: PCI (cc 0x804, rev 0x09, vendor 0x4243) > ssb: Switching to ChipCommon core, index 0 > ssb: Switching to PCI core, index 4 > wmaster0: Selected rate control algorithm 'simple' > bcm43xx_d80211: Broadcom 4306 WLAN found > ssb: Switching to IEEE 802.11 core, index 1 > ssb: Switching to PCI core, index 4 > ssb: Switching to IEEE 802.11 core, index 1 > bcm43xx_d80211: Found PHY: Version 2, Type 2, Revision 2 > bcm43xx_d80211: Found Radio: Manuf 0x17F, Version 0x2050, Revision 2 > bcm43xx_d80211: Loading firmware version 319.102 (2005-10-15 22:46:19) > ssb: Switching to ChipCommon core, index 0 > ssb: Switching to IEEE 802.11 core, index 1 > bcm43xx_d80211: Radio turned on > bcm43xx_d80211: Chip initialized > bcm43xx_d80211: 30-bit DMA initialized > bcm43xx_d80211: Wireless interface started > eth1: Does not support passive scan, disabled > wlan0_rename: dropped data frame to not associated station 00:00:00:00:00:00 > wlan0_rename: dropped data frame to not associated station 00:00:00:00:00:00 > wlan0_rename: dropped data frame to not associated station 00:00:00:00:00:00 > > "iwlist scan" shows many access points in range, but neither interface > apparently attached to this card will associate, even if I explicitly > set access point and ESSID: > > # iwconfig wlan0_rename essid nicta_wireless ap 00:13:5F:54:EB:70 > # dmesg > wlan0_rename: Initial auth_alg=0 > wlan0_rename: authenticate with AP 00:13:5f:54:eb:70 > wlan0_rename: RX authentication from 00:13:5f:54:eb:70 (alg=0 transaction=2 > status=0) > wlan0_rename: authenticated > wlan0_rename: associate with AP 00:13:5f:54:eb:70 > wlan0_rename: authentication frame received from 00:13:5f:54:eb:70, but not > in authenticate state - ignored > wlan0_rename: RX AssocResp from 00:13:5f:54:eb:70 (capab=0x421 status=0 > aid=116) > wlan0_rename: associated > eth1: Added STA 00:13:5f:54:eb:70 > wlan0_rename: WMM queue=2 aci=0 acm=0 aifs=3 cWmin=15 cWmax=1023 burst=0 > wlan0_rename: WMM queue=3 aci=1 acm=0 aifs=7 cWmin=15 cWmax=1023 burst=0 > wlan0_rename: WMM queue=1 aci=2 acm=0 aifs=2 cWmin=7 cWmax=15 burst=30 > wlan0_rename: WMM queue=0 aci=3 acm=0 aifs=2 cWmin=3 cWmax=7 burst=15 > wlan0_rename: association frame received from 00:13:5f:54:eb:70, but not in > associate state - ignored > > > -- > Dr Peter Chubb http://www.gelato.unsw.edu.au peterc AT gelato.unsw.edu.au > http://www.ertos.nicta.com.au ERTOS within National ICT Australia > > -- Greetings Michael. _______________________________________________ Bcm43xx-dev mailing list [email protected] https://lists.berlios.de/mailman/listinfo/bcm43xx-dev
