On Sunday 11 February 2007 15:02, Rafael J. Wysocki wrote: > On Sunday, 11 February 2007 14:07, Michael Buesch wrote: > > On Sunday 11 February 2007 13:56, Rafael J. Wysocki wrote: > > > On Saturday, 10 February 2007 21:33, Larry Finger wrote: > > > > Rafael, > > > > > > > > Rafael J. Wysocki wrote: > > > > > > > > > > I'm running with this patch applied right now, but the association is > > > > > lost > > > > > after the resume anyway. I have to reload bcm43xx to make it > > > > > associate with > > > > > the AP again (no big deal). > > > > > > > > > > > > Please send me the output of iwconfig and ifconfig after the resume, > > > > but before you reload bcm43xx. > > > > > > albercik:~ # iwconfig > > > lo no wireless extensions. > > > > > > eth0 no wireless extensions. > > > > > > eth1 IEEE 802.11b/g ESSID:"DI524" Nickname:"Broadcom 4311" > > > Mode:Managed Frequency=2.484 GHz Access Point: Invalid > > > Bit Rate=1 Mb/s Tx-Power=18 dBm > > > RTS thr:off Fragment thr:off > > > Encryption key:off > > > Link Quality=0/100 Signal level=-256 dBm Noise level=-256 dBm > > > Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 > > > Tx excessive retries:0 Invalid misc:0 Missed beacon:0 > > > > > > albercik:~ # ifconfig eth1 > > > eth1 Link encap:Ethernet HWaddr 00:14:A5:BE:95:31 > > > inet addr:192.168.100.101 Bcast:192.168.100.255 > > > Mask:255.255.255.0 > > > inet6 addr: fe80::214:a5ff:febe:9531/64 Scope:Link > > > UP BROADCAST MULTICAST MTU:1500 Metric:1 > > > RX packets:5137 errors:0 dropped:120 overruns:0 frame:0 > > > TX packets:5703 errors:0 dropped:0 overruns:0 carrier:0 > > > collisions:0 txqueuelen:1000 > > > RX bytes:4569090 (4.3 Mb) TX bytes:156826797 (149.5 Mb) > > > Interrupt:18 > > > > > > albercik:~ # ifconfig eth1 down > > > albercik:~ # ifconfig eth1 up > > > SIOCSIFFLAGS: No such device > > ^^^^^ > > > > I'd like to see dmesg, please. > > Appended. It covers one suspend-resume cycle (suspend to disk). I have > filtered HID-related messages out of it. > > Greetings, > Rafael > > > ton.000e = 0 > usb 3-1: usb auto-resume > ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [0] = 0x00040103 PSSC PPS > PES CCS > usb 3-1: finish resume > usb usb1: usb auto-resume > usb usb1: finish resume > hub 1-0:1.0: hub_resume > ehci_hcd 0000:00:13.2: resume root hub > hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0000 > usb 3-1: usb auto-suspend > hub 1-0:1.0: hub_suspend > usb usb1: usb auto-suspend > PM: Adding info for No Bus:vcs8 > PM: Adding info for No Bus:vcsa8 > SoftMAC: Scanning finished: scanned 14 channels starting with channel 1 > Stopping tasks ... done. > Shrinking memory... -\|/-\|/-\done (113015 pages freed) > Freed 452060 kbytes in 1.44 seconds (313.93 MB/s) > Suspending console(s) > usbhid 3-4:1.0: freeze > usb 3-4: freeze > usbhid 3-4:1.0: suspend > usb 3-4: usb suspend > usbdev3.18: PM: suspend 0->1, parent 3-1 already 2 > usbdev3.18_ep02: PM: suspend 0->1, parent 3-1:1.0 already 2 > usbdev3.18_ep81: PM: suspend 0->1, parent 3-1:1.0 already 2 > usb 3-1:1.0: PM: suspend 2-->1 > usb 3-1:1.0: PM: suspend 2->1, parent 3-1 already 2 > usbdev3.18_ep00: PM: suspend 0->1, parent 3-1 already 2 > usb 3-1: PM: suspend 2-->1 > usb 2-2:1.3: freeze > usb 2-2:1.2: freeze > hci_usb 2-2:1.1: freeze > hci_usb 2-2:1.0: freeze > usb 2-2: freeze > usb 2-2: usb suspend > serio serio6: freeze > platform bluetooth: freeze > hub 3-0:1.0: freeze > usb usb3: freeze > hub 3-0:1.0: hub_suspend > ohci_hcd 0000:00:13.1: suspend root hub > usb usb3: usb suspend > hub 2-0:1.0: freeze > usb usb2: freeze > hub 2-0:1.0: hub_suspend > ohci_hcd 0000:00:13.0: suspend root hub > usb usb2: usb suspend > usbdev1.1: PM: suspend 0->1, parent usb1 already 2 > usbdev1.1_ep81: PM: suspend 0->1, parent 1-0:1.0 already 2 > hub 1-0:1.0: PM: suspend 2-->1 > hub 1-0:1.0: PM: suspend 2->1, parent usb1 already 2 > usbdev1.1_ep00: PM: suspend 0->1, parent usb1 already 2 > usb usb1: PM: suspend 2-->1 > ide-cdrom 0.0: freeze > psmouse serio4: freeze > serio serio3: freeze > serio serio2: freeze > serio serio1: freeze > atkbd serio0: freeze > i8042 i8042: freeze > sd 0:0:0:0: freeze > serial8250 serial8250: freeze > vesafb vesafb.0: freeze > pci_express 0000:00:06.0:pcie03: freeze > pci_express 0000:00:06.0:pcie01: freeze > pci_express 0000:00:06.0:pcie00: freeze > pci_express 0000:00:05.0:pcie03: freeze > pci_express 0000:00:05.0:pcie01: freeze > pci_express 0000:00:05.0:pcie00: freeze > pci_express 0000:00:04.0:pcie03: freeze > pci_express 0000:00:04.0:pcie01: freeze > pci_express 0000:00:04.0:pcie00: freeze > pcspkr pcspkr: freeze > sdhci 0000:02:04.3: freeze > ACPI: PCI interrupt for device 0000:02:04.3 disabled > tifm_7xx1 0000:02:04.2: freeze > ACPI: PCI interrupt for device 0000:02:04.2 disabled > ohci1394 0000:02:04.1: freeze > ohci1394 does not fully support suspend and resume yet > ieee1394: hpsb_bus_reset called while bus reset already in progress > yenta_cardbus 0000:02:04.0: freeze > tg3 0000:02:01.0: freeze > PM: Writing back config space on device 0000:02:01.0 at offset b (was > 3ed173b, writing 30b0103c) > PM: Writing back config space on device 0000:02:01.0 at offset 3 (was 0, > writing 4010) > PM: Writing back config space on device 0000:02:01.0 at offset 2 (was > 2000000, writing 2000003) > PM: Writing back config space on device 0000:02:01.0 at offset 1 (was > 2b00000, writing 2b00006) > PM: Writing back config space on device 0000:02:01.0 at offset 0 (was > 3ed173b, writing 169c14e4) > bcm43xx 0000:30:00.0: freeze > bcm43xx: Suspending... > PM: Removing info for No Bus:hw_random > bcm43xx: Radio turned off > bcm43xx: DMA-32 0x0200 (RX) max used slots: 3/64 > bcm43xx: DMA-32 0x02A0 (TX) max used slots: 0/512 > bcm43xx: DMA-32 0x0280 (TX) max used slots: 0/512 > bcm43xx: DMA-32 0x0260 (TX) max used slots: 0/512 > bcm43xx: DMA-32 0x0240 (TX) max used slots: 0/512 > bcm43xx: DMA-32 0x0220 (TX) max used slots: 3/512 > bcm43xx: DMA-32 0x0200 (TX) max used slots: 0/512 > ACPI: PCI interrupt for device 0000:30:00.0 disabled > bcm43xx: Device suspended. > pci 0000:01:05.0: freeze > k8temp 0000:00:18.3: freeze > pci 0000:00:18.2: freeze > pci 0000:00:18.1: freeze > pci 0000:00:18.0: freeze > pci 0000:00:14.4: freeze > pci 0000:00:14.3: freeze > HDA Intel 0000:00:14.2: freeze > ACPI: PCI interrupt for device 0000:00:14.2 disabled > ATIIXP_IDE 0000:00:14.1: freeze > piix4_smbus 0000:00:14.0: freeze > ehci_hcd 0000:00:13.2: freeze > ACPI: PCI interrupt for device 0000:00:13.2 disabled > ehci_hcd 0000:00:13.2: --> PCI D3 > ohci_hcd 0000:00:13.1: freeze > ACPI: PCI interrupt for device 0000:00:13.1 disabled > ohci_hcd 0000:00:13.1: --> PCI D0/legacy > ohci_hcd 0000:00:13.0: freeze > ACPI: PCI interrupt for device 0000:00:13.0 disabled > ohci_hcd 0000:00:13.0: --> PCI D0/legacy > sata_sil 0000:00:12.0: freeze > pcieport-driver 0000:00:06.0: freeze > pcieport-driver 0000:00:05.0: freeze > pcieport-driver 0000:00:04.0: freeze > pci 0000:00:01.0: freeze > pci 0000:00:00.0: freeze > ACPI Thermal Zone Driver thermal:03: freeze > ACPI Thermal Zone Driver thermal:02: freeze > ACPI Thermal Zone Driver thermal:01: freeze > ACPI Fan Driver PNP0C0B:03: freeze > ACPI Fan Driver PNP0C0B:02: freeze > ACPI: Transitioning device [C351] to D0 > ACPI: Transitioning device [C351] to D0 > ACPI Fan Driver PNP0C0B:01: freeze > ACPI: Transitioning device [C350] to D0 > ACPI: Transitioning device [C350] to D0 > ACPI Fan Driver PNP0C0B:00: freeze > ACPI: Transitioning device [C34F] to D0 > ACPI: Transitioning device [C34F] to D0 > ACPI Power Resource Driver power_resource:06: freeze > ACPI Power Resource Driver power_resource:05: freeze > ACPI Power Resource Driver power_resource:04: freeze > ACPI Power Resource Driver power_resource:03: freeze > acpi thermal:00: freeze > acpi PNP0C02:02: freeze > acpi PNP0C14:00: freeze > ACPI Button Driver PNP0C0D:00: freeze > ACPI Button Driver PNP0C0E:00: freeze > ACPI AC Adapter Driver ACPI0003:00: freeze > ACPI Battery Driver PNP0C0A:01: freeze > ACPI Battery Driver PNP0C0A:00: freeze > acpi HPQ0006:00: freeze > acpi PNP0C02:01: freeze > acpi device:49: freeze > acpi device:48: freeze > acpi device:47: freeze > acpi device:46: freeze > acpi device:45: freeze > acpi device:44: freeze > acpi device:43: freeze > acpi device:42: freeze > acpi device:41: freeze > acpi device:40: freeze > acpi device:3f: freeze > acpi device:3e: freeze > acpi device:3d: freeze > acpi device:3c: freeze > acpi device:3b: freeze > acpi device:3a: freeze > acpi device:39: freeze > acpi device:38: freeze > acpi device:37: freeze > acpi device:36: freeze > acpi device:35: freeze > acpi device:34: freeze > acpi device:33: freeze > ACPI PCI Interrupt Link Driver PNP0C0F:07: freeze > ACPI PCI Interrupt Link Driver PNP0C0F:06: freeze > ACPI PCI Interrupt Link Driver PNP0C0F:05: freeze > ACPI PCI Interrupt Link Driver PNP0C0F:04: freeze > ACPI PCI Interrupt Link Driver PNP0C0F:03: freeze > ACPI PCI Interrupt Link Driver PNP0C0F:02: freeze > ACPI PCI Interrupt Link Driver PNP0C0F:01: freeze > ACPI PCI Interrupt Link Driver PNP0C0F:00: freeze > acpi device:32: freeze > acpi device:31: freeze > acpi device:30: freeze > acpi device:2f: freeze > acpi device:2e: freeze > acpi device:2d: freeze > acpi device:2c: freeze > acpi device:2b: freeze > acpi device:2a: freeze > acpi device:29: freeze > acpi device:28: freeze > acpi device:27: freeze > acpi device:26: freeze > acpi device:25: freeze > acpi device:24: freeze > acpi device:23: freeze > acpi device:22: freeze > acpi device:21: freeze > acpi device:20: freeze > acpi device:1f: freeze > acpi device:1e: freeze > acpi device:1d: freeze > acpi device:1c: freeze > acpi device:1b: freeze > acpi device:1a: freeze > acpi device:19: freeze > acpi device:18: freeze > acpi device:17: freeze > acpi device:16: freeze > acpi device:15: freeze > acpi device:14: freeze > acpi device:13: freeze > acpi device:12: freeze > acpi device:11: freeze > acpi device:10: freeze > acpi PNP0C02:00: freeze > acpi PNP0000:00: freeze > ACPI Power Resource Driver power_resource:02: freeze > acpi SYN0118:00: freeze > acpi PNP0303:00: freeze > acpi PNP0B00:00: freeze > acpi PNP0800:00: freeze > acpi PNP0200:00: freeze > acpi PNP0100:00: freeze > acpi PNP0C04:00: freeze > acpi IFX0102:00: freeze > ACPI Power Resource Driver power_resource:01: freeze > acpi PNP0401:00: freeze > ACPI container driver PNP0A06:00: freeze > ACPI Embedded Controller Driver PNP0C09:00: freeze > acpi device:0f: freeze > acpi device:0e: freeze > ACPI Power Resource Driver power_resource:00: freeze > acpi device:0d: freeze > acpi device:0c: freeze > acpi device:0b: freeze > acpi device:0a: freeze > acpi device:09: freeze > acpi device:08: freeze > acpi device:07: freeze > acpi device:06: freeze > acpi device:05: freeze > acpi device:04: freeze > acpi device:03: freeze > acpi device:02: freeze > acpi video:00: freeze > acpi device:01: freeze > ACPI PCI Root Bridge Driver PNP0A03:00: freeze > acpi PNP0C01:00: freeze > acpi device:00: freeze > ACPI Processor Driver ACPI0007:01: freeze > ACPI Processor Driver ACPI0007:00: freeze > ACPI Button Driver button_power:00: freeze > acpi acpi_system:00: freeze > Disabling non-boot CPUs ... > CPU 1 is now offline > SMP alternatives: switching to UP code > CPU1 is down > platform bluetooth: LATE freeze > i8042 i8042: LATE freeze > serial8250 serial8250: LATE freeze > vesafb vesafb.0: LATE freeze > pcspkr pcspkr: LATE freeze > sdhci 0000:02:04.3: LATE freeze > tifm_7xx1 0000:02:04.2: LATE freeze > ohci1394 0000:02:04.1: LATE freeze > yenta_cardbus 0000:02:04.0: LATE freeze > tg3 0000:02:01.0: LATE freeze > bcm43xx 0000:30:00.0: LATE freeze > pci 0000:01:05.0: LATE freeze > k8temp 0000:00:18.3: LATE freeze > pci 0000:00:18.2: LATE freeze > pci 0000:00:18.1: LATE freeze > pci 0000:00:18.0: LATE freeze > pci 0000:00:14.4: LATE freeze > pci 0000:00:14.3: LATE freeze > HDA Intel 0000:00:14.2: LATE freeze > ATIIXP_IDE 0000:00:14.1: LATE freeze > piix4_smbus 0000:00:14.0: LATE freeze > pcieport-driver 0000:00:06.0: LATE freeze > pcieport-driver 0000:00:05.0: LATE freeze > pcieport-driver 0000:00:04.0: LATE freeze > pci 0000:00:01.0: LATE freeze > pci 0000:00:00.0: LATE freeze > Extended CMOS year: 2000 > swsusp: critical section: > swsusp: Need to copy 95157 pages > swsusp: Normal pages needed: 95157 + 1024 + 20, available pages: 134073 > Extended CMOS year: 2000 > pci 0000:00:00.0: EARLY resume > pci 0000:00:01.0: EARLY resume > pcieport-driver 0000:00:04.0: EARLY resume > pcieport-driver 0000:00:05.0: EARLY resume > pcieport-driver 0000:00:06.0: EARLY resume > sata_sil 0000:00:12.0: EARLY resume > ohci_hcd 0000:00:13.0: EARLY resume > ohci_hcd 0000:00:13.1: EARLY resume > ehci_hcd 0000:00:13.2: EARLY resume > piix4_smbus 0000:00:14.0: EARLY resume > ATIIXP_IDE 0000:00:14.1: EARLY resume > HDA Intel 0000:00:14.2: EARLY resume > pci 0000:00:14.3: EARLY resume > pci 0000:00:14.4: EARLY resume > pci 0000:00:18.0: EARLY resume > pci 0000:00:18.1: EARLY resume > pci 0000:00:18.2: EARLY resume > k8temp 0000:00:18.3: EARLY resume > pci 0000:01:05.0: EARLY resume > bcm43xx 0000:30:00.0: EARLY resume > tg3 0000:02:01.0: EARLY resume > yenta_cardbus 0000:02:04.0: EARLY resume > ohci1394 0000:02:04.1: EARLY resume > tifm_7xx1 0000:02:04.2: EARLY resume > sdhci 0000:02:04.3: EARLY resume > pcspkr pcspkr: EARLY resume > vesafb vesafb.0: EARLY resume > serial8250 serial8250: EARLY resume > i8042 i8042: EARLY resume > platform bluetooth: EARLY resume > Enabling non-boot CPUs ... > SMP alternatives: switching to SMP code > Booting processor 1/2 APIC 0x1 > Initializing CPU#1 > Calibrating delay using timer specific routine.. 3990.23 BogoMIPS > (lpj=7980462) > CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) > CPU: L2 Cache: 512K (64 bytes/line) > CPU: Physical Processor ID: 0 > CPU: Processor Core ID: 1 > AMD Turion(tm) 64 X2 Mobile Technology TL-60 stepping 02 > CPU 1: Syncing TSC to CPU 0. > CPU 1: synchronized TSC with CPU 0 (last diff 0 cycles, maxerr 510 cycles) > powernow-k8: 0 : fid 0xc (2000 MHz), vid 0x13 > powernow-k8: 1 : fid 0xa (1800 MHz), vid 0x15 > powernow-k8: 2 : fid 0x8 (1600 MHz), vid 0x17 > powernow-k8: 3 : fid 0x0 (800 MHz), vid 0x1e > CPU1 is up > acpi acpi_system:00: resuming > ACPI Button Driver button_power:00: resuming > ACPI Processor Driver ACPI0007:00: resuming > ACPI Processor Driver ACPI0007:01: resuming > acpi device:00: resuming > acpi PNP0C01:00: resuming > ACPI PCI Root Bridge Driver PNP0A03:00: resuming > acpi device:01: resuming > acpi video:00: resuming > acpi device:02: resuming > acpi device:03: resuming > acpi device:04: resuming > acpi device:05: resuming > acpi device:06: resuming > acpi device:07: resuming > acpi device:08: resuming > acpi device:09: resuming > acpi device:0a: resuming > acpi device:0b: resuming > acpi device:0c: resuming > acpi device:0d: resuming > ACPI Power Resource Driver power_resource:00: resuming > acpi device:0e: resuming > acpi device:0f: resuming > ACPI Embedded Controller Driver PNP0C09:00: resuming > ACPI container driver PNP0A06:00: resuming > acpi PNP0401:00: resuming > ACPI Power Resource Driver power_resource:01: resuming > acpi IFX0102:00: resuming > acpi PNP0C04:00: resuming > acpi PNP0100:00: resuming > acpi PNP0200:00: resuming > acpi PNP0800:00: resuming > acpi PNP0B00:00: resuming > acpi PNP0303:00: resuming > acpi SYN0118:00: resuming > ACPI Power Resource Driver power_resource:02: resuming > acpi PNP0000:00: resuming > acpi PNP0C02:00: resuming > acpi device:10: resuming > acpi device:11: resuming > acpi device:12: resuming > acpi device:13: resuming > acpi device:14: resuming > acpi device:15: resuming > acpi device:16: resuming > acpi device:17: resuming > acpi device:18: resuming > acpi device:19: resuming > acpi device:1a: resuming > acpi device:1b: resuming > acpi device:1c: resuming > acpi device:1d: resuming > acpi device:1e: resuming > acpi device:1f: resuming > acpi device:20: resuming > acpi device:21: resuming > acpi device:22: resuming > acpi device:23: resuming > acpi device:24: resuming > acpi device:25: resuming > acpi device:26: resuming > acpi device:27: resuming > acpi device:28: resuming > acpi device:29: resuming > acpi device:2a: resuming > acpi device:2b: resuming > acpi device:2c: resuming > acpi device:2d: resuming > acpi device:2e: resuming > acpi device:2f: resuming > acpi device:30: resuming > acpi device:31: resuming > acpi device:32: resuming > ACPI PCI Interrupt Link Driver PNP0C0F:00: resuming > ACPI PCI Interrupt Link Driver PNP0C0F:01: resuming > ACPI PCI Interrupt Link Driver PNP0C0F:02: resuming > ACPI PCI Interrupt Link Driver PNP0C0F:03: resuming > ACPI PCI Interrupt Link Driver PNP0C0F:04: resuming > ACPI PCI Interrupt Link Driver PNP0C0F:05: resuming > ACPI PCI Interrupt Link Driver PNP0C0F:06: resuming > ACPI PCI Interrupt Link Driver PNP0C0F:07: resuming > acpi device:33: resuming > acpi device:34: resuming > acpi device:35: resuming > acpi device:36: resuming > acpi device:37: resuming > acpi device:38: resuming > acpi device:39: resuming > acpi device:3a: resuming > acpi device:3b: resuming > acpi device:3c: resuming > acpi device:3d: resuming > acpi device:3e: resuming > acpi device:3f: resuming > acpi device:40: resuming > acpi device:41: resuming > acpi device:42: resuming > acpi device:43: resuming > acpi device:44: resuming > acpi device:45: resuming > acpi device:46: resuming > acpi device:47: resuming > acpi device:48: resuming > acpi device:49: resuming > acpi PNP0C02:01: resuming > acpi HPQ0006:00: resuming > ACPI Battery Driver PNP0C0A:00: resuming > ACPI Battery Driver PNP0C0A:01: resuming > ACPI AC Adapter Driver ACPI0003:00: resuming > ACPI Button Driver PNP0C0E:00: resuming > ACPI Button Driver PNP0C0D:00: resuming > acpi PNP0C14:00: resuming > acpi PNP0C02:02: resuming > acpi thermal:00: resuming > ACPI Power Resource Driver power_resource:03: resuming > ACPI Power Resource Driver power_resource:04: resuming > ACPI Power Resource Driver power_resource:05: resuming > ACPI Power Resource Driver power_resource:06: resuming > ACPI Fan Driver PNP0C0B:00: resuming > ACPI: Transitioning device [C34F] to D0 > ACPI: Transitioning device [C34F] to D0 > ACPI Fan Driver PNP0C0B:01: resuming > ACPI: Transitioning device [C350] to D0 > ACPI: Transitioning device [C350] to D0 > ACPI Fan Driver PNP0C0B:02: resuming > ACPI: Transitioning device [C351] to D0 > ACPI: Transitioning device [C351] to D0 > ACPI Fan Driver PNP0C0B:03: resuming > ACPI Thermal Zone Driver thermal:01: resuming > ACPI Thermal Zone Driver thermal:02: resuming > ACPI Thermal Zone Driver thermal:03: resuming > pci 0000:00:00.0: resuming > pci 0000:00:01.0: resuming > pcieport-driver 0000:00:04.0: resuming > PCI: Setting latency timer of device 0000:00:04.0 to 64 > pcieport-driver 0000:00:05.0: resuming > PCI: Setting latency timer of device 0000:00:05.0 to 64 > pcieport-driver 0000:00:06.0: resuming > PCI: Setting latency timer of device 0000:00:06.0 to 64 > sata_sil 0000:00:12.0: resuming > ohci_hcd 0000:00:13.0: resuming > ohci_hcd 0000:00:13.0: PCI legacy resume > ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 19 (level, low) -> IRQ 19 > ohci_hcd 0000:00:13.1: resuming > ohci_hcd 0000:00:13.1: PCI legacy resume > ACPI: PCI Interrupt 0000:00:13.1[A] -> GSI 19 (level, low) -> IRQ 19 > ehci_hcd 0000:00:13.2: resuming > ehci_hcd 0000:00:13.2: PCI D0, from previous PCI D3 > ACPI: PCI Interrupt 0000:00:13.2[A] -> GSI 19 (level, low) -> IRQ 19 > PM: Writing back config space on device 0000:00:13.2 at offset 1 (was > 2b00007, writing 2b00017) > ehci_hcd 0000:00:13.2: lost power, restarting > usb usb1: root hub lost power or was reset > ehci_hcd 0000:00:13.2: reset command 080002 (park)=0 ithresh=8 period=1024 > Reset HALT > ehci_hcd 0000:00:13.2: MWI active > piix4_smbus 0000:00:14.0: resuming > ATIIXP_IDE 0000:00:14.1: resuming > ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 16 > HDA Intel 0000:00:14.2: resuming > PM: Writing back config space on device 0000:00:14.2 at offset f (was 10a, > writing a) > PM: Writing back config space on device 0000:00:14.2 at offset 1 (was > 4100006, writing 4100002) > ACPI: PCI Interrupt 0000:00:14.2[A] -> GSI 16 (level, low) -> IRQ 16 > pci 0000:00:14.3: resuming > pci 0000:00:14.4: resuming > PM: Writing back config space on device 0000:00:14.4 at offset 6 (was > 40030200, writing 40060200) > pci 0000:00:18.0: resuming > pci 0000:00:18.1: resuming > pci 0000:00:18.2: resuming > k8temp 0000:00:18.3: resuming > pci 0000:01:05.0: resuming > bcm43xx 0000:30:00.0: resuming > bcm43xx: Resuming... > ACPI: PCI Interrupt 0000:30:00.0[A] -> GSI 18 (level, low) -> IRQ 18 > bcm43xx: PHY connected > bcm43xx: Microcode rev 0x127, pl 0xe (2005-04-18 02:36:27) > bcm43xx: Radio turned on > bcm43xx: Radio enabled by hardware > ata2: SATA link down (SStatus 0 SControl 300) > bcm43xx: Chip initialized > bcm43xx: 32-bit DMA initialized > bcm43xx: Keys cleared > bcm43xx: Selected 802.11 core (phytype 2) > PM: Adding info for No Bus:hw_random > bcm43xx: Device resumed. > tg3 0000:02:01.0: resuming > PM: Writing back config space on device 0000:02:01.0 at offset b (was > 3ed173b, writing 30b0103c) > PM: Writing back config space on device 0000:02:01.0 at offset 3 (was 0, > writing 4010) > PM: Writing back config space on device 0000:02:01.0 at offset 2 (was > 2000000, writing 2000003) > PM: Writing back config space on device 0000:02:01.0 at offset 1 (was > 2b00000, writing 2b00006) > PM: Writing back config space on device 0000:02:01.0 at offset 0 (was > 3ed173b, writing 169c14e4) > SoftMAC: Associate: Scanning for networks first. > yenta_cardbus 0000:02:04.0: resuming > PM: Writing back config space on device 0000:02:04.0 at offset f (was > 3c4010a, writing 5c0010a) > PM: Writing back config space on device 0000:02:04.0 at offset 3 (was 824010, > writing 82a810) > ohci1394 0000:02:04.1: resuming > ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[20] MMIO=[d4011000-d40117ff] > Max Packet=[2048] IR/IT contexts=[4/8] > tifm_7xx1 0000:02:04.2: resuming > ACPI: PCI Interrupt 0000:02:04.2[A] -> GSI 20 (level, low) -> IRQ 20 > sdhci 0000:02:04.3: resuming > ACPI: PCI Interrupt 0000:02:04.3[A] -> GSI 20 (level, low) -> IRQ 20 > pcspkr pcspkr: resuming > pci_express 0000:00:04.0:pcie00: resuming > pci_express 0000:00:04.0:pcie01: resuming > pci_express 0000:00:04.0:pcie03: resuming > pci_express 0000:00:05.0:pcie00: resuming > pci_express 0000:00:05.0:pcie01: resuming > pci_express 0000:00:05.0:pcie03: resuming > pci_express 0000:00:06.0:pcie00: resuming > pci_express 0000:00:06.0:pcie01: resuming > pci_express 0000:00:06.0:pcie03: resuming > vesafb vesafb.0: resuming > serial8250 serial8250: resuming > sd 0:0:0:0: resuming > i8042 i8042: resuming > atkbd serio0: resuming > serio serio1: resuming > serio serio2: resuming > serio serio3: resuming > psmouse serio4: resuming > synaptics reset failed > synaptics reset failed > synaptics reset failed > SoftMAC: Scanning finished: scanned 14 channels starting with channel 1 > ide-cdrom 0.0: resuming > usb usb1: resuming > usb usb1: usb resume > usb usb1: finish resume > hub 1-0:1.0: hub_resume > ehci_hcd 0000:00:13.2: resume root hub after power loss > usb usb2: resuming > usb usb2: usb resume > usb usb2: finish resume > hub 2-0:1.0: hub_resume > ohci_hcd 0000:00:13.0: BIOS/SMM active, control 008 > usb usb2: root hub lost power or was reset > ohci_hcd 0000:00:13.0: resetting from state 'reset', control = 0x8 > ohci_hcd 0000:00:13.0: OHCI controller state > ohci_hcd 0000:00:13.0: OHCI 1.0, NO legacy support registers > ohci_hcd 0000:00:13.0: control 0x083 HCFS=operational CBSR=3 > ohci_hcd 0000:00:13.0: cmdstatus 0x00000 SOC=0 > ohci_hcd 0000:00:13.0: intrstatus 0x00000004 SF > ohci_hcd 0000:00:13.0: intrenable 0x8000005a MIE RHSC UE RD WDH > ohci_hcd 0000:00:13.0: hcca frame #0005 > ohci_hcd 0000:00:13.0: roothub.a 02000204 POTPGT=2 NPS NDP=4(4) > ohci_hcd 0000:00:13.0: roothub.b 00000000 PPCM=0000 DR=0000 > ohci_hcd 0000:00:13.0: roothub.status 00008000 DRWE > ohci_hcd 0000:00:13.0: roothub.portstatus [0] 0x00000100 PPS > ohci_hcd 0000:00:13.0: roothub.portstatus [1] 0x00010100 CSC PPS > ohci_hcd 0000:00:13.0: roothub.portstatus [2] 0x00000100 PPS > ohci_hcd 0000:00:13.0: roothub.portstatus [3] 0x00000100 PPS > ohci_hcd 0000:00:13.0: restart complete > hub 2-0:1.0: resuming > usb usb3: resuming > usb usb3: usb resume > usb usb3: finish resume > hub 3-0:1.0: hub_resume > ohci_hcd 0000:00:13.1: BIOS/SMM active, control 008 > usb usb3: root hub lost power or was reset > ohci_hcd 0000:00:13.1: resetting from state 'reset', control = 0x8 > ohci_hcd 0000:00:13.1: OHCI controller state > ohci_hcd 0000:00:13.1: OHCI 1.0, NO legacy support registers > ohci_hcd 0000:00:13.1: control 0x083 HCFS=operational CBSR=3 > ohci_hcd 0000:00:13.1: cmdstatus 0x00000 SOC=0 > ohci_hcd 0000:00:13.1: intrstatus 0x00000004 SF > ohci_hcd 0000:00:13.1: intrenable 0x8000005a MIE RHSC UE RD WDH > ohci_hcd 0000:00:13.1: hcca frame #0005 > ohci_hcd 0000:00:13.1: roothub.a 02000204 POTPGT=2 NPS NDP=4(4) > ohci_hcd 0000:00:13.1: roothub.b 00000000 PPCM=0000 DR=0000 > ohci_hcd 0000:00:13.1: roothub.status 00008000 DRWE > ohci_hcd 0000:00:13.1: roothub.portstatus [0] 0x00010100 CSC PPS > ohci_hcd 0000:00:13.1: roothub.portstatus [1] 0x00000100 PPS > ohci_hcd 0000:00:13.1: roothub.portstatus [2] 0x00000100 PPS > ohci_hcd 0000:00:13.1: roothub.portstatus [3] 0x00010100 CSC PPS > ohci_hcd 0000:00:13.1: restart complete > hub 3-0:1.0: resuming > platform bluetooth: resuming > serio serio6: resuming > usb 2-2: resuming > usbdev2.10_ep00: PM: resume from 0, parent 2-2 still 1 > hci_usb 2-2:1.0: PM: resume from 1, parent 2-2 still 1 > hci_usb 2-2:1.0: resuming > hci0: PM: resume from 0, parent 2-2:1.0 still 1 > usbdev2.10_ep81: PM: resume from 0, parent 2-2:1.0 still 1 > usbdev2.10_ep82: PM: resume from 0, parent 2-2:1.0 still 1 > usbdev2.10_ep02: PM: resume from 0, parent 2-2:1.0 still 1 > hci_usb 2-2:1.1: PM: resume from 1, parent 2-2 still 1 > hci_usb 2-2:1.1: resuming > usbdev2.10_ep83: PM: resume from 0, parent 2-2:1.1 still 1 > usbdev2.10_ep03: PM: resume from 0, parent 2-2:1.1 still 1 > usb 2-2:1.2: PM: resume from 1, parent 2-2 still 1 > usb 2-2:1.2: resuming > usbdev2.10_ep84: PM: resume from 0, parent 2-2:1.2 still 1 > usbdev2.10_ep04: PM: resume from 0, parent 2-2:1.2 still 1 > usb 2-2:1.3: PM: resume from 1, parent 2-2 still 1 > usb 2-2:1.3: resuming > usbdev2.10: PM: resume from 0, parent 2-2 still 1 > usbdev3.18_ep00: PM: resume from 0, parent 3-1 still 2 > usbdev3.18_ep81: PM: resume from 0, parent 3-1:1.0 still 2 > usbdev3.18_ep02: PM: resume from 0, parent 3-1:1.0 still 2 > usbdev3.18: PM: resume from 0, parent 3-1 still 2 > usb 3-4: resuming > usbdev3.19_ep00: PM: resume from 0, parent 3-4 still 1 > usbhid 3-4:1.0: PM: resume from 1, parent 3-4 still 1 > usbhid 3-4:1.0: resuming > usbdev3.19_ep81: PM: resume from 0, parent 3-4:1.0 still 1 > usbdev3.19: PM: resume from 0, parent 3-4 still 1 > Restarting tasks ... <7>hub 2-0:1.0: state 7 ports 4 chg 0004 evt 001e > ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [0] = 0x00010100 CSC PPS > hub 2-0:1.0: port 1, status 0100, change 0001, 12 Mb/s > done. > PM: Removing info for No Bus:vcs8 > PM: Removing info for No Bus:vcsa8 > ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) > ata1.00: configured for UDMA/100 > SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB) > sda: Write Protect is off > sda: Mode Sense: 00 3a 00 00 > SCSI device sda: write cache: enabled, read cache: enabled, doesn't support > DPO or FUA > hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100 > ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [1] = 0x00010100 CSC PPS > hub 2-0:1.0: port 2, status 0100, change 0001, 12 Mb/s > usb 2-2: USB disconnect, address 10 > usb 2-2: unregistering device > usb 2-2: usb_disable_device nuking all URBs > usb 2-2: unregistering interface 2-2:1.0 > PM: Removing info for No Bus:usbdev2.10_ep81 > usbdev2.10_ep81: ep_device_release called for usbdev2.10_ep81 > PM: Removing info for No Bus:usbdev2.10_ep82 > usbdev2.10_ep82: ep_device_release called for usbdev2.10_ep82 > PM: Removing info for No Bus:usbdev2.10_ep02 > usbdev2.10_ep02: ep_device_release called for usbdev2.10_ep02 > PM: Removing info for No Bus:hci0 > PM: Removing info for usb:2-2:1.0 > usb 2-2:1.0: uevent > usb 2-2: unregistering interface 2-2:1.1 > PM: Removing info for No Bus:usbdev2.10_ep83 > usbdev2.10_ep83: ep_device_release called for usbdev2.10_ep83 > PM: Removing info for No Bus:usbdev2.10_ep03 > usbdev2.10_ep03: ep_device_release called for usbdev2.10_ep03 > PM: Removing info for usb:2-2:1.1 > usb 2-2:1.1: uevent > usb 2-2: unregistering interface 2-2:1.2 > PM: Removing info for No Bus:usbdev2.10_ep84 > usbdev2.10_ep84: ep_device_release called for usbdev2.10_ep84 > PM: Removing info for No Bus:usbdev2.10_ep04 > usbdev2.10_ep04: ep_device_release called for usbdev2.10_ep04 > PM: Removing info for usb:2-2:1.2 > usb 2-2:1.2: uevent > usb 2-2: unregistering interface 2-2:1.3 > PM: Removing info for usb:2-2:1.3 > usb 2-2:1.3: uevent > PM: Removing info for No Bus:usbdev2.10 > PM: Removing info for No Bus:usbdev2.10_ep00 > usbdev2.10_ep00: ep_device_release called for usbdev2.10_ep00 > PM: Removing info for usb:2-2 > usb 2-2: uevent > SoftMAC: Scanning finished: scanned 14 channels starting with channel 1 > hub 2-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x100 > ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [2] = 0x00010100 CSC PPS > hub 2-0:1.0: port 3, status 0100, change 0001, 12 Mb/s > hub 2-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x100 > ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [3] = 0x00010100 CSC PPS > hub 2-0:1.0: port 4, status 0100, change 0001, 12 Mb/s > hub 2-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x100 > hub 3-0:1.0: state 7 ports 4 chg 0012 evt 001e > ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [0] = 0x00010100 CSC PPS > hub 3-0:1.0: port 1, status 0100, change 0001, 12 Mb/s > usb 3-1: USB disconnect, address 18 > usb 3-1: unregistering device > usb 3-1: usb_disable_device nuking all URBs > usb 3-1: unregistering interface 3-1:1.0 > PM: Removing info for No Bus:usbdev3.18_ep81 > usbdev3.18_ep81: ep_device_release called for usbdev3.18_ep81 > PM: Removing info for No Bus:usbdev3.18_ep02 > usbdev3.18_ep02: ep_device_release called for usbdev3.18_ep02 > PM: Removing info for usb:3-1:1.0 > usb 3-1:1.0: uevent > PM: Removing info for No Bus:usbdev3.18 > PM: Removing info for No Bus:usbdev3.18_ep00 > usbdev3.18_ep00: ep_device_release called for usbdev3.18_ep00 > PM: Removing info for usb:3-1 > usb 3-1: uevent > hub 3-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100 > ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [1] = 0x00010100 CSC PPS > hub 3-0:1.0: port 2, status 0100, change 0001, 12 Mb/s > hub 3-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x100 > ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [2] = 0x00010100 CSC PPS > hub 3-0:1.0: port 3, status 0100, change 0001, 12 Mb/s > hub 3-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x100 > ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [3] = 0x00010100 CSC PPS > hub 3-0:1.0: port 4, status 0100, change 0001, 12 Mb/s > usb 3-4: USB disconnect, address 19 > usb 3-4: unregistering device > usb 3-4: usb_disable_device nuking all URBs > usb 3-4: unregistering interface 3-4:1.0 > PM: Removing info for No Bus:usbdev3.19_ep81 > usbdev3.19_ep81: ep_device_release called for usbdev3.19_ep81 > PM: Removing info for usb:3-4:1.0 > usb 3-4:1.0: uevent > PM: Removing info for No Bus:usbdev3.19 > PM: Removing info for No Bus:usbdev3.19_ep00 > usbdev3.19_ep00: ep_device_release called for usbdev3.19_ep00 > PM: Removing info for usb:3-4 > usb 3-4: uevent > hub 3-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x100 > hub 1-0:1.0: state 7 ports 8 chg 0000 evt 010c > ehci_hcd 0000:00:13.2: GetStatus port 2 status 001803 POWER sig=j CSC CONNECT > hub 1-0:1.0: port 2, status 0501, change 0001, 480 Mb/s > hub 1-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x501 > ehci_hcd 0000:00:13.2: port 2 full speed --> companion > ehci_hcd 0000:00:13.2: GetStatus port 2 status 003801 POWER OWNER sig=j > CONNECT > hub 1-0:1.0: port 2 not reset yet, waiting 50ms > ehci_hcd 0000:00:13.2: GetStatus port 2 status 003002 POWER OWNER sig=se0 CSC > ehci_hcd 0000:00:13.2: GetStatus port 3 status 001803 POWER sig=j CSC CONNECT > hub 1-0:1.0: port 3, status 0501, change 0001, 480 Mb/s > hub 1-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x501 > ehci_hcd 0000:00:13.2: port 3 full speed --> companion > ehci_hcd 0000:00:13.2: GetStatus port 3 status 003801 POWER OWNER sig=j > CONNECT > hub 1-0:1.0: port 3 not reset yet, waiting 50ms > ehci_hcd 0000:00:13.2: GetStatus port 3 status 003002 POWER OWNER sig=se0 CSC > ehci_hcd 0000:00:13.2: GetStatus port 8 status 001403 POWER sig=k CSC CONNECT > hub 1-0:1.0: port 8, status 0501, change 0001, 480 Mb/s > hub 1-0:1.0: debounce: port 8: total 100ms stable 100ms status 0x501 > ehci_hcd 0000:00:13.2: port 8 low speed --> companion > ehci_hcd 0000:00:13.2: GetStatus port 8 status 003002 POWER OWNER sig=se0 CSC > hub 2-0:1.0: state 7 ports 4 chg 0000 evt 0004 > ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [1] = 0x00010101 CSC PPS > CCS > hub 2-0:1.0: port 2, status 0101, change 0001, 12 Mb/s > hub 2-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x101 > ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [1] = 0x00100103 PRSC PPS > PES CCS > usb 2-2: new full speed USB device using ohci_hcd and address 11 > ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [1] = 0x00100103 PRSC PPS > PES CCS > usb 2-2: skipped 1 descriptor after interface > usb 2-2: default language 0x0409 > usb 2-2: new device strings: Mfr=1, Product=2, SerialNumber=0 > usb 2-2: Product: HP Integrated Module > usb 2-2: Manufacturer: Broadcom Corp > PM: Adding info for usb:2-2 > usb 2-2: uevent > usb 2-2: usb_probe_device > PM: Adding info for No Bus:usbdev2.11_ep00 > usb 2-2: configuration #1 chosen from 1 choice > usb 2-2: adding 2-2:1.0 (config #1, interface 0) > PM: Adding info for usb:2-2:1.0 > usb 2-2:1.0: uevent > hci_usb 2-2:1.0: usb_probe_interface > hci_usb 2-2:1.0: usb_probe_interface - got id > PM: Adding info for No Bus:hci0 > PM: Adding info for No Bus:usbdev2.11_ep81 > PM: Adding info for No Bus:usbdev2.11_ep82 > PM: Adding info for No Bus:usbdev2.11_ep02 > usb 2-2: adding 2-2:1.1 (config #1, interface 1) > PM: Adding info for usb:2-2:1.1 > usb 2-2:1.1: uevent > PM: Adding info for No Bus:usbdev2.11_ep83 > PM: Adding info for No Bus:usbdev2.11_ep03 > usb 2-2: adding 2-2:1.2 (config #1, interface 2) > PM: Adding info for usb:2-2:1.2 > usb 2-2:1.2: uevent > hci_usb 2-2:1.2: usb_probe_interface > hci_usb 2-2:1.2: usb_probe_interface - got id > PM: Adding info for No Bus:usbdev2.11_ep84 > PM: Adding info for No Bus:usbdev2.11_ep04 > usb 2-2: adding 2-2:1.3 (config #1, interface 3) > PM: Adding info for usb:2-2:1.3 > usb 2-2:1.3: uevent > hci_usb 2-2:1.3: usb_probe_interface > hci_usb 2-2:1.3: usb_probe_interface - got id > PM: Adding info for No Bus:usbdev2.11 > drivers/usb/core/inode.c: creating file '011' > hub 3-0:1.0: state 7 ports 4 chg 0000 evt 0012 > ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [0] = 0x00010101 CSC PPS > CCS > hub 3-0:1.0: port 1, status 0101, change 0001, 12 Mb/s > hub 3-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101 > ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [0] = 0x00100103 PRSC PPS > PES CCS > usb 3-1: new full speed USB device using ohci_hcd and address 20 > ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [0] = 0x00100103 PRSC PPS > PES CCS > usb 3-1: ep0 maxpacket = 8 > usb 3-1: default language 0x0409 > usb 3-1: new device strings: Mfr=0, Product=1, SerialNumber=0 > usb 3-1: Product: Fingerprint Sensor > PM: Adding info for usb:3-1 > usb 3-1: uevent > usb 3-1: usb_probe_device > PM: Adding info for No Bus:usbdev3.20_ep00 > usb 3-1: configuration #1 chosen from 1 choice > usb 3-1: adding 3-1:1.0 (config #1, interface 0) > PM: Adding info for usb:3-1:1.0 > usb 3-1:1.0: uevent > PM: Adding info for No Bus:usbdev3.20_ep81 > PM: Adding info for No Bus:usbdev3.20_ep02 > PM: Adding info for No Bus:usbdev3.20 > drivers/usb/core/inode.c: creating file '020' > ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [3] = 0x00010301 CSC LSDA > PPS CCS > hub 3-0:1.0: port 4, status 0301, change 0001, 1.5 Mb/s > hub 3-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x301 > ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [3] = 0x00100303 PRSC > LSDA PPS PES CCS > usb 3-4: new low speed USB device using ohci_hcd and address 21 > ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [3] = 0x00100303 PRSC > LSDA PPS PES CCS > usb 3-4: skipped 1 descriptor after interface > usb 3-4: default language 0x0409 > usb 3-4: new device strings: Mfr=1, Product=2, SerialNumber=0 > usb 3-4: Product: USB Receiver > usb 3-4: Manufacturer: Logitech > PM: Adding info for usb:3-4 > usb 3-4: uevent > usb 3-4: usb_probe_device > PM: Adding info for No Bus:usbdev3.21_ep00 > usb 3-4: configuration #1 chosen from 1 choice > usb 3-4: adding 3-4:1.0 (config #1, interface 0) > PM: Adding info for usb:3-4:1.0 > usb 3-4:1.0: uevent > usbhid 3-4:1.0: usb_probe_interface > usbhid 3-4:1.0: usb_probe_interface - got id > INPUT[INPUT] > Field(0) > Physical(GenericDesktop.Pointer) > Usage(8) > Button.0001 > Button.0002 > Button.0003 > Button.0004 > Button.0005 > Button.0006 > Button.0007 > Button.0008 > Logical Minimum(0) > Logical Maximum(1) > Report Size(1) > Report Count(8) > Report Offset(0) > Flags( Variable Absolute ) > Field(1) > Physical(GenericDesktop.Pointer) > Usage(3) > GenericDesktop.X > GenericDesktop.Y > GenericDesktop.Wheel > Logical Minimum(-127) > Logical Maximum(127) > Report Size(8) > Report Count(3) > Report Offset(8) > Flags( Variable Relative ) > Field(2) > Physical(GenericDesktop.Pointer) > Usage(1) > Consumer.HorizontalWheel > Logical Minimum(-127) > Logical Maximum(127) > Report Size(8) > Report Count(1) > Report Offset(32) > Flags( Variable Relative ) > Field(3) > Usage(8) > LED.GenericIndicator > LED.GenericIndicator > LED.GenericIndicator > LED.GenericIndicator > LED.GenericIndicator > LED.GenericIndicator > LED.GenericIndicator > LED.GenericIndicator > Logical Minimum(0) > Logical Maximum(1) > Report Size(1) > Report Count(8) > Report Offset(40) > Flags( Variable Absolute ) > Field(4) > Usage(8) > Button.0009 > Button.000a > Button.000b > Button.000c > Button.000d > Button.000e > Button.000f > Button.0010 > Logical Minimum(0) > Logical Maximum(1) > Report Size(1) > Report Count(8) > Report Offset(48) > Flags( Variable Absolute ) > FEATURE[FEATURE] > Field(0) > Usage(1) > GenericDesktop.MotionWakeup > Logical Minimum(0) > Logical Maximum(1) > Report Size(1) > Report Count(1) > Report Offset(0) > Flags( Variable Absolute NoPrefferedState ) > Mapping: Button.0001 ---> Key.LeftBtn > Mapping: Button.0002 ---> Key.RightBtn > Mapping: Button.0003 ---> Key.MiddleBtn > Mapping: Button.0004 ---> Key.SideBtn > Mapping: Button.0005 ---> Key.ExtraBtn > Mapping: Button.0006 ---> Key.ForwardBtn > Mapping: Button.0007 ---> Key.BackBtn > Mapping: Button.0008 ---> Key.TaskBtn > Mapping: GenericDesktop.X ---> Relative.X > Mapping: GenericDesktop.Y ---> Relative.Y > Mapping: GenericDesktop.Wheel ---> Relative.Wheel > Mapping: Consumer.HorizontalWheel ---> Relative.HWheel > Mapping: LED.GenericIndicator ---> LED.Misc > Mapping: LED.GenericIndicator ---> LED.? > Mapping: LED.GenericIndicator ---> LED.? > Mapping: LED.GenericIndicator ---> LED.? > Mapping: LED.GenericIndicator ---> LED.? > Mapping: LED.GenericIndicator ---> LED.? > Mapping: LED.GenericIndicator ---> LED.? > Mapping: LED.GenericIndicator ---> LED.? > Mapping: Button.0009 ---> Key.? > Mapping: Button.000a ---> Key.? > Mapping: Button.000b ---> Key.? > Mapping: Button.000c ---> Key.? > Mapping: Button.000d ---> Key.? > Mapping: Button.000e ---> Key.? > Mapping: Button.000f ---> Key.? > Mapping: Button.0010 ---> Key.? > input: Logitech USB Receiver as /class/input/input16 > hid-pidff: starting pid init > hid-pidff: not a PID device, no output report > input: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:13.1-4 > PM: Adding info for No Bus:usbdev3.21_ep81 > PM: Adding info for No Bus:usbdev3.21 > drivers/usb/core/inode.c: creating file '021' > hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0100 > hub 2-0:1.0: state 7 ports 4 chg 0000 evt 0004 > hub 3-0:1.0: state 7 ports 4 chg 0000 evt 0002 > usb 3-1: usb auto-suspend > SoftMAC: Scanning finished: scanned 14 channels starting with channel 1 > hub 1-0:1.0: hub_suspend > usb usb1: usb auto-suspend > SoftMAC: Scanning finished: scanned 14 channels starting with channel 1 > PM: Removing info for No Bus:hw_random > bcm43xx: Radio turned off > bcm43xx: DMA-32 0x0200 (RX) max used slots: 0/64 > bcm43xx: DMA-32 0x02A0 (TX) max used slots: 0/512 > bcm43xx: DMA-32 0x0280 (TX) max used slots: 0/512 > bcm43xx: DMA-32 0x0260 (TX) max used slots: 0/512 > bcm43xx: DMA-32 0x0240 (TX) max used slots: 0/512 > bcm43xx: DMA-32 0x0220 (TX) max used slots: 56/512 > bcm43xx: DMA-32 0x0200 (TX) max used slots: 0/512 > PM: Adding info for No Bus:0000:30:00.0 > PM: Removing info for No Bus:0000:30:00.0 > PM: Adding info for No Bus:0000:30:00.0 > PM: Removing info for No Bus:0000:30:00.0 > PM: Adding info for No Bus:0000:30:00.0 > PM: Removing info for No Bus:0000:30:00.0 > PM: Adding info for No Bus:0000:30:00.0 > PM: Removing info for No Bus:0000:30:00.0 > bcm43xx: IRQ_READY timeout > bcm43xx: core_up for active 802.11 core failed (-19)
I never tried suspend to disk with the driver. Larry, an idea why the microcode doesn't respond? -- Greetings Michael. _______________________________________________ Bcm43xx-dev mailing list Bcm43xx-dev@lists.berlios.de https://lists.berlios.de/mailman/listinfo/bcm43xx-dev
