Ioannis Nousias wrote: > this is what I get now in dmesg: > > SoftMAC: Scanning finished: scanned 13 channels starting with channel 1 > ieee80211_crypt: registered algorithm 'TKIP' > bcm43xx: set security called, .active_key = 0, .level = 2, .enabled = 1, > .encrypt = 1 > bcm43xx: set security called, .enabled = 1, .encrypt = 1 > eth1: no IPv6 routers present > SoftMAC: sent association request! > bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0 > bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0 > bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0 > bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0 > bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0 > bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0 > bcm43xx: Radio turned off > bcm43xx: DMA-32 0x0260 (RX) max used slots: 1/64 > bcm43xx: DMA-32 0x0200 (RX) max used slots: 1/64 > bcm43xx: DMA-32 0x02A0 (TX) max used slots: 0/512 > bcm43xx: DMA-32 0x0280 (TX) max used slots: 0/512 > bcm43xx: DMA-32 0x0260 (TX) max used slots: 0/512 > bcm43xx: DMA-32 0x0240 (TX) max used slots: 0/512 > bcm43xx: DMA-32 0x0220 (TX) max used slots: 65/512 > bcm43xx: DMA-32 0x0200 (TX) max used slots: 0/512 > bcm43xx: PHY disconnected > bcm43xx: PHY connected > bcm43xx: Microcode rev 0x127, pl 0xe (2005-04-18 02:36:27) > bcm43xx: Radio turned on > bcm43xx: Radio enabled by hardware > bcm43xx: Chip initialized > bcm43xx: 30-bit DMA initialized > bcm43xx: TODO: Incomplete code in keymac_write() at > /home/s0238762/Desktop/bcm43xx-softmac-sa/bcm43xx/bcm43xx_m > ain.c:1144
These messages can be ignored. > bcm43xx: TODO: Incomplete code in keymac_write() at > /home/s0238762/Desktop/bcm43xx-softmac-sa/bcm43xx/bcm43xx_m > ain.c:1146 > ... > bcm43xx: Keys cleared > bcm43xx: Selected 802.11 core (phytype 2) > ADDRCONF(NETDEV_UP): eth1: link is not ready > > > I'm sitting 5meters apart from the router. The signal indication in > NetworkManager is nearly full strength. > > at least we are getting there. Thanks The fact that you are seeing signal in NetworkManager means that scanning is working. Please send the output of the ifconfig and iwconfig commands once NM has tried to connect. What percentage does NM reach before it stops trying? Are you using any encryption? > PS: This standalone one is from April. Are there any recent ones? No - there have not been any changes since 2.6.21-rc1. > PS2: once loaded the module can not be removed. rmmod (or modprobe -r) > do nothing on it. I have not seen this problem before. Are there any messages in the logs or on the console? Larry > > > > _______________________________________________ Bcm43xx-dev mailing list [email protected] https://lists.berlios.de/mailman/listinfo/bcm43xx-dev
