Hi. I'm just testing new b43 branch, and there are a lot of progress made over softmac version. I'm sharing network with my friend in building where signal is very weak. I couldn't connect with softmac version, but with mac80211 connection is good, no disconnections. It is little slower than ndiswrapper, and link quality sometimes goes above 100 and goes fast up and down in wavemon. Ndiswrapper shows max 10.
ACPI: PCI Interrupt 0000:06:02.0[A] -> GSI 22 (level, low) -> IRQ 21 ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x0D, vendor 0x4243) ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x09, vendor 0x4243) ssb: Core 2 found: PCI (cc 0x804, rev 0x0C, vendor 0x4243) ssb: Core 3 found: PCMCIA (cc 0x80D, rev 0x07, vendor 0x4243) ssb: Sonics Silicon Backplane found on PCI device 0000:06:02.0 b43-phy2: Broadcom 4318 WLAN found b43-phy2 debug: Found PHY: Analog 3, Type 2, Revision 7 b43-phy2 debug: Found Radio: Manuf 0x17F, Version 0x2050, Revision 8 b43-phy2 debug: Radio turned off b43-phy2 debug: DebugFS (CONFIG_DEBUG_FS) not enabled in kernel config wmaster0: Selected rate control algorithm 'simple' b43-phy2 debug: Adding Interface type 2 b43-phy2 debug: Loading firmware version 351.126 (2006-07-29 05:54:02) b43-phy2 debug: Radio turned on b43-phy2 debug: Radio enabled by hardware b43-phy2 ERROR: bbatt(11) >= size of LO array b43-phy2 debug: Chip initialized b43-phy2 debug: 32-bit DMA initialized b43-phy2 debug: Wireless interface started HW CONFIG: channel=1 freq=2412 phymode=3 b43-phy2 debug: Removing Interface type 2 b43-phy2 debug: Wireless interface stopped b43-phy2 debug: DMA-32 0x0200 (RX) max used slots: 0/64 b43-phy2 debug: DMA-32 0x02A0 (TX) max used slots: 0/128 b43-phy2 debug: DMA-32 0x0280 (TX) max used slots: 0/128 b43-phy2 debug: DMA-32 0x0260 (TX) max used slots: 0/128 b43-phy2 debug: DMA-32 0x0240 (TX) max used slots: 0/128 b43-phy2 debug: DMA-32 0x0220 (TX) max used slots: 0/128 b43-phy2 debug: DMA-32 0x0200 (TX) max used slots: 0/128 b43-phy2 debug: Radio turned off b43-phy2 debug: Radio turned off b43-phy2 debug: Adding Interface type 2 b43-phy2 debug: Loading firmware version 351.126 (2006-07-29 05:54:02) b43-phy2 debug: Radio turned on b43-phy2 debug: Radio enabled by hardware b43-phy2 debug: Chip initialized b43-phy2 debug: 32-bit DMA initialized b43-phy2 debug: Wireless interface started HW CONFIG: channel=1 freq=2412 phymode=3 HW CONFIG: channel=1 freq=2412 phymode=3 Is "b43-phy2 ERROR: bbatt(11) >= size of LO array" this error normal? _______________________________________________ Bcm43xx-dev mailing list [email protected] https://lists.berlios.de/mailman/listinfo/bcm43xx-dev
