Ivan Majhen wrote: > Hi. I'm just testing new b43 branch, and there are a lot of progress made > over > softmac version. > I'm sharing network with my friend in building where signal is very weak. I > couldn't connect with softmac version, but with mac80211 connection is good, > no disconnections. It is little slower than ndiswrapper, and link quality > sometimes goes above 100 and goes fast up and down in wavemon. Ndiswrapper > shows max 10. > > ACPI: PCI Interrupt 0000:06:02.0[A] -> GSI 22 (level, low) -> IRQ 21 > ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x0D, vendor 0x4243) > ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x09, vendor 0x4243) > ssb: Core 2 found: PCI (cc 0x804, rev 0x0C, vendor 0x4243) > ssb: Core 3 found: PCMCIA (cc 0x80D, rev 0x07, vendor 0x4243) > ssb: Sonics Silicon Backplane found on PCI device 0000:06:02.0 > b43-phy2: Broadcom 4318 WLAN found > b43-phy2 debug: Found PHY: Analog 3, Type 2, Revision 7 > b43-phy2 debug: Found Radio: Manuf 0x17F, Version 0x2050, Revision 8 > b43-phy2 debug: Radio turned off > b43-phy2 debug: DebugFS (CONFIG_DEBUG_FS) not enabled in kernel config > wmaster0: Selected rate control algorithm 'simple' > b43-phy2 debug: Adding Interface type 2 > b43-phy2 debug: Loading firmware version 351.126 (2006-07-29 05:54:02) > b43-phy2 debug: Radio turned on > b43-phy2 debug: Radio enabled by hardware > b43-phy2 ERROR: bbatt(11) >= size of LO array > b43-phy2 debug: Chip initialized > b43-phy2 debug: 32-bit DMA initialized > b43-phy2 debug: Wireless interface started > HW CONFIG: channel=1 freq=2412 phymode=3 > b43-phy2 debug: Removing Interface type 2 > b43-phy2 debug: Wireless interface stopped > b43-phy2 debug: DMA-32 0x0200 (RX) max used slots: 0/64 > b43-phy2 debug: DMA-32 0x02A0 (TX) max used slots: 0/128 > b43-phy2 debug: DMA-32 0x0280 (TX) max used slots: 0/128 > b43-phy2 debug: DMA-32 0x0260 (TX) max used slots: 0/128 > b43-phy2 debug: DMA-32 0x0240 (TX) max used slots: 0/128 > b43-phy2 debug: DMA-32 0x0220 (TX) max used slots: 0/128 > b43-phy2 debug: DMA-32 0x0200 (TX) max used slots: 0/128 > b43-phy2 debug: Radio turned off > b43-phy2 debug: Radio turned off > b43-phy2 debug: Adding Interface type 2 > b43-phy2 debug: Loading firmware version 351.126 (2006-07-29 05:54:02) > b43-phy2 debug: Radio turned on > b43-phy2 debug: Radio enabled by hardware > b43-phy2 debug: Chip initialized > b43-phy2 debug: 32-bit DMA initialized > b43-phy2 debug: Wireless interface started > HW CONFIG: channel=1 freq=2412 phymode=3 > HW CONFIG: channel=1 freq=2412 phymode=3 > > Is "b43-phy2 ERROR: bbatt(11) >= size of LO array" this error normal?
If you had bothered to look at the archives, you would know the answer to this question! Larry _______________________________________________ Bcm43xx-dev mailing list [email protected] https://lists.berlios.de/mailman/listinfo/bcm43xx-dev
