> > OK, after bootup with v2.5.25-rc3-git I get this, looks sane to me: > > [ 32.474786] b43-phy0: Loading firmware version 351.126 (2006-07-29 > 05:54:02) > [ 32.474797] b43-phy0 warning: You are using an old firmware image. > Support for old firmware will be removed in July 2008. > [ 32.474802] b43-phy0 warning: You must go to > http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and > download the latest firmware (version 4). > [ 30.137115] warning: `avahi-daemon' uses 32-bit capabilities (legacy > support in use) > [ 32.774279] PM: Adding info for No Bus:vcs7 > [ 32.774317] PM: Adding info for No Bus:vcsa7 > [ 31.049445] PM: Adding info for No Bus:hw_random > [ 31.062460] b43-phy0: Radio hardware status changed to DISABLED > [ 31.773470] b43-phy0: Radio turned on by software > [ 31.773475] b43-phy0: The hardware RF-kill button still turns the > radio physically off. Press the button to turn it on. > [ 45.919959] NET: Registered protocol family 17 > [ 54.874707] NET: Registered protocol family 10 > [ 54.875253] lo: Disabled Privacy Extensions > [ 54.878600] ADDRCONF(NETDEV_UP): wlan0: link is not ready > [ 67.096841] eth0: no IPv6 routers present > > As for the original question I had, interrupts seem sane too. > > [EMAIL PROTECTED]:~$ cat /proc/interrupts|grep "19:" > 19: 0 185 IO-APIC-fasteoi b43 >
Forgot to mension that rfkill-led is behaving as I described earlier, and has been for as long as I can remember. I don't have specific kernel versions, sorry. It is always blue, as in wlan active, except if I disable wireless in knetworkmanager. Killswitch doesn't affect the led. disable wireless in knetworkmanager, radio hw disabled, led turns red [ 1333.692522] PM: Removing info for No Bus:event7 [ 1333.716523] PM: Removing info for No Bus:input7 [ 1333.716600] PM: Removing info for No Bus:rfkill0 [ 1333.728542] PM: Removing info for No Bus:hw_random [ 1378.346660] PM: Adding info for No Bus:rfkill1 [ 1378.708529] PM: Adding info for No Bus:input8 [ 1378.708568] input: b43-phy0 as /class/input/input8 [ 1378.757574] PM: Adding info for No Bus:event7 [ 1378.949550] b43-phy0: Loading firmware version 351.126 (2006-07-29 05:54:02) [ 1378.949563] b43-phy0 warning: You are using an old firmware image. Support for old firmware will be removed in July 2008. [ 1378.949567] b43-phy0 warning: You must go to http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the latest firmware (version 4). enable wireless again, radio hw still disabled, led turns blue [ 1380.606214] PM: Adding info for No Bus:hw_random [ 1380.685925] b43-phy0: Radio hardware status changed to DISABLED [ 1380.698005] ADDRCONF(NETDEV_UP): wlan0: link is not ready flipping switch a few times, led unchanged [ 1534.770048] b43-phy0: Radio hardware status changed to ENABLED [ 1550.778511] b43-phy0: Radio hardware status changed to DISABLED [ 1562.783474] b43-phy0: Radio hardware status changed to ENABLED [ 1565.788237] b43-phy0: Radio hardware status changed to DISABLED regards, Richard _______________________________________________ Bcm43xx-dev mailing list [email protected] https://lists.berlios.de/mailman/listinfo/bcm43xx-dev
