Larry Finger skrev:
Richard Jonsson wrote:
Larry Finger skrev:
If Linus's latest git still has the problem, please do a bisection. I
I've now completed the bisection, result below. I'm not really sure this
is the bad commit, as v2.6.25 is fine, and this commit is from february.
But then again, I don't fully understand how git does it's bisection.
I've also tried a few kernels in the 2.6.25-rc series that don't show
this problem.
That part is not too difficult to understand. When the commit was made
in February, it was to the wireless-testing tree for inclusion in
2.6.26. Only when Linus went to the 2.6.25-git kernels in the process
of getting to 2.6.26-rc1 did that commit make it to mainline.
Oh, I see.
Do you have the ssb and b43 debug info from one of the "bad" kernels?
Please post that info from /var/log/messages. It seems as though this
problem shows on your system because you have a multi-band device.
Attached. To my knowledge this card (4311) has B/G support=2.4GHz only,
whereas 4312 has A/B/G support=2.4/5GHz.
regards, Richard
[ 21.435367] ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x11, vendor 0x4243)
[ 21.435435] ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x0A, vendor
0x4243)
[ 21.435505] ssb: Core 2 found: USB 1.1 Host (cc 0x817, rev 0x03, vendor
0x4243)
[ 21.435575] ssb: Core 3 found: PCI-E (cc 0x820, rev 0x01, vendor 0x4243)
[ 21.459105] ssb: SPROM revision 2 detected.
[ 21.489484] PM: Adding info for ssb:ssb0:0
[ 21.489504] PM: Adding info for ssb:ssb0:1
[ 21.489515] ssb: Sonics Silicon Backplane found on PCI device 0000:01:00.0
[ 21.877727] b43-phy0: Broadcom 4311 WLAN found
[ 21.937251] b43-phy0 debug: Found PHY: Analog 4, Type 2, Revision 8
[ 21.937272] b43-phy0 debug: Found Radio: Manuf 0x17F, Version 0x2050,
Revision 2
[ 29.557703] input: b43-phy0 as /class/input/input7
[ 29.673737] PM: Adding info for No Bus:ssb0:0
[ 29.727250] PM: Removing info for No Bus:ssb0:0
[ 29.727330] PM: Adding info for No Bus:ssb0:0
[ 29.766160] PM: Removing info for No Bus:ssb0:0
[ 29.766231] PM: Adding info for No Bus:ssb0:0
[ 29.770747] PM: Removing info for No Bus:ssb0:0
[ 29.770818] PM: Adding info for No Bus:ssb0:0
[ 29.787375] PM: Removing info for No Bus:ssb0:0
[ 29.906425] b43-phy0: Loading firmware version 351.126 (2006-07-29 05:54:02)
[ 29.906436] b43-phy0 warning: You are using an old firmware image. Support
for old firmware will be removed in July 2008.
[ 29.906440] b43-phy0 warning: You must go to
http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the
latest firmware (version 4).
[ 30.774037] b43-phy0 debug: Chip initialized
[ 30.774277] b43-phy0 debug: 32-bit DMA initialized
[ 30.793997] PM: Adding info for No Bus:b43-phy0::tx
[ 30.794014] Registered led device: b43-phy0::tx
[ 30.794024] PM: Adding info for No Bus:b43-phy0::rx
[ 30.794036] Registered led device: b43-phy0::rx
[ 30.794047] PM: Adding info for No Bus:b43-phy0::radio
[ 30.794059] Registered led device: b43-phy0::radio
[ 30.794089] b43-phy0 debug: Wireless interface started
[ 30.794095] b43-phy0 debug: Adding Interface type 2
[ 30.794110] b43-phy0: Radio hardware status changed to DISABLED
[ 30.885777] b43-phy0: Radio turned on by software
[ 30.885786] b43-phy0: The hardware RF-kill button still turns the radio
physically off. Press the button to turn it on.
[ 32.273863] b43-phy0 debug: Switching to 5-GHz band
[ 32.273886] b43-phy0 debug: Wireless interface stopped
[ 32.273898] PM: Removing info for No Bus:b43-phy0::tx
[ 32.273943] PM: Removing info for No Bus:b43-phy0::rx
[ 32.273970] PM: Removing info for No Bus:b43-phy0::radio
[ 32.274017] b43-phy0 debug: DMA-32 rx_ring: Used slots 0/64, Failed frames
0/0 = 0.0%, Average tries 0.00
[ 32.274053] b43-phy0 debug: DMA-32 tx_ring_AC_BK: Used slots 0/128, Failed
frames 0/0 = 0.0%, Average tries 0.00
[ 32.281867] b43-phy0 debug: DMA-32 tx_ring_AC_BE: Used slots 0/128, Failed
frames 0/0 = 0.0%, Average tries 0.00
[ 32.289861] b43-phy0 debug: DMA-32 tx_ring_AC_VI: Used slots 0/128, Failed
frames 0/0 = 0.0%, Average tries 0.00
[ 32.297862] b43-phy0 debug: DMA-32 tx_ring_AC_VO: Used slots 2/128, Failed
frames 0/11 = 0.0%, Average tries 1.00
[ 32.305862] b43-phy0 debug: DMA-32 tx_ring_mcast: Used slots 0/128, Failed
frames 0/0 = 0.0%, Average tries 0.00
[ 32.473900] b43-phy0: Loading firmware version 351.126 (2006-07-29 05:54:02)
[ 32.473909] b43-phy0 warning: You are using an old firmware image. Support
for old firmware will be removed in July 2008.
[ 32.473914] b43-phy0 warning: You must go to
http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the
latest firmware (version 4).
[ 33.185972] b43-phy0 debug: Chip initialized
[ 33.186129] b43-phy0 debug: 32-bit DMA initialized
[ 33.206147] PM: Adding info for No Bus:b43-phy0::tx
[ 33.206165] Registered led device: b43-phy0::tx
[ 33.206175] PM: Adding info for No Bus:b43-phy0::rx
[ 33.206187] Registered led device: b43-phy0::rx
[ 33.206198] PM: Adding info for No Bus:b43-phy0::radio
[ 33.206209] Registered led device: b43-phy0::radio
[ 33.206229] b43-phy0 debug: Wireless interface started
[ 33.206254] b43-phy0 ERROR: PHY transmission error
[ 33.237956] b43-phy0 ERROR: PHY transmission error
[ 33.238029] b43-phy0 ERROR: PHY transmission error
[ 33.238042] b43-phy0 ERROR: PHY transmission error
[ 33.238051] b43-phy0 ERROR: PHY transmission error
[ 33.238067] b43-phy0 ERROR: PHY transmission error
[ 33.238078] b43-phy0 ERROR: PHY transmission error
[ 33.985983] b43-phy0 debug: Switching to 2.4-GHz band
[ 33.986007] b43-phy0 debug: Wireless interface stopped
[ 33.986021] PM: Removing info for No Bus:b43-phy0::tx
[ 33.986084] PM: Removing info for No Bus:b43-phy0::rx
[ 33.986111] PM: Removing info for No Bus:b43-phy0::radio
[ 33.986161] b43-phy0 debug: DMA-32 rx_ring: Used slots 0/64, Failed frames
0/0 = 0.0%, Average tries 0.00
[ 33.986201] b43-phy0 debug: DMA-32 tx_ring_AC_BK: Used slots 0/128, Failed
frames 0/0 = 0.0%, Average tries 0.00
[ 33.993977] b43-phy0 debug: DMA-32 tx_ring_AC_BE: Used slots 0/128, Failed
frames 0/0 = 0.0%, Average tries 0.00
[ 34.001978] b43-phy0 debug: DMA-32 tx_ring_AC_VI: Used slots 0/128, Failed
frames 0/0 = 0.0%, Average tries 0.00
[ 34.009974] b43-phy0 debug: DMA-32 tx_ring_AC_VO: Used slots 6/128, Failed
frames 0/10 = 0.0%, Average tries 1.00
[ 34.017992] b43-phy0 debug: DMA-32 tx_ring_mcast: Used slots 0/128, Failed
frames 0/0 = 0.0%, Average tries 0.00
[ 34.185991] b43-phy0: Loading firmware version 351.126 (2006-07-29 05:54:02)
[ 34.186003] b43-phy0 warning: You are using an old firmware image. Support
for old firmware will be removed in July 2008.
[ 34.186009] b43-phy0 warning: You must go to
http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the
latest firmware (version 4).
[ 35.042324] b43-phy0 debug: Chip initialized
[ 35.042524] b43-phy0 debug: 32-bit DMA initialized
[ 35.062444] PM: Adding info for No Bus:b43-phy0::tx
[ 35.062463] Registered led device: b43-phy0::tx
[ 35.062475] PM: Adding info for No Bus:b43-phy0::rx
[ 35.062488] Registered led device: b43-phy0::rx
[ 35.062500] PM: Adding info for No Bus:b43-phy0::radio
[ 35.062512] Registered led device: b43-phy0::radio
[ 35.062543] b43-phy0 debug: Wireless interface started
[ 62.311748] b43-phy0 debug: Switching to 5-GHz band
[ 62.311778] b43-phy0 debug: Wireless interface stopped
[ 62.311793] PM: Removing info for No Bus:b43-phy0::tx
[ 62.311848] PM: Removing info for No Bus:b43-phy0::rx
[ 62.311876] PM: Removing info for No Bus:b43-phy0::radio
[ 62.311927] b43-phy0 debug: DMA-32 rx_ring: Used slots 0/64, Failed frames
0/0 = 0.0%, Average tries 0.00
[ 62.311967] b43-phy0 debug: DMA-32 tx_ring_AC_BK: Used slots 0/128, Failed
frames 0/0 = 0.0%, Average tries 0.00
[ 62.319748] b43-phy0 debug: DMA-32 tx_ring_AC_BE: Used slots 0/128, Failed
frames 0/0 = 0.0%, Average tries 0.00
[ 62.327744] b43-phy0 debug: DMA-32 tx_ring_AC_VI: Used slots 0/128, Failed
frames 0/0 = 0.0%, Average tries 0.00
[ 62.335739] b43-phy0 debug: DMA-32 tx_ring_AC_VO: Used slots 2/128, Failed
frames 0/11 = 0.0%, Average tries 1.00
[ 62.343739] b43-phy0 debug: DMA-32 tx_ring_mcast: Used slots 0/128, Failed
frames 0/0 = 0.0%, Average tries 0.00
[ 62.511754] b43-phy0: Loading firmware version 351.126 (2006-07-29 05:54:02)
[ 62.511762] b43-phy0 warning: You are using an old firmware image. Support
for old firmware will be removed in July 2008.
[ 62.511767] b43-phy0 warning: You must go to
http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the
latest firmware (version 4).
[ 63.223848] b43-phy0 debug: Chip initialized
[ 63.224042] b43-phy0 debug: 32-bit DMA initialized
[ 63.244027] PM: Adding info for No Bus:b43-phy0::tx
[ 63.244044] Registered led device: b43-phy0::tx
[ 63.244056] PM: Adding info for No Bus:b43-phy0::rx
[ 63.244069] Registered led device: b43-phy0::rx
[ 63.244084] PM: Adding info for No Bus:b43-phy0::radio
[ 63.244097] Registered led device: b43-phy0::radio
[ 63.244119] b43-phy0 debug: Wireless interface started
[ 63.244149] b43-phy0 ERROR: PHY transmission error
[ 63.283864] b43-phy0 ERROR: PHY transmission error
[ 63.283902] b43-phy0: Radio hardware status changed to DISABLED
[ 63.983857] b43-phy0 debug: Switching to 2.4-GHz band
[ 63.983894] b43-phy0 debug: Wireless interface stopped
[ 63.983908] PM: Removing info for No Bus:b43-phy0::tx
[ 63.983969] PM: Removing info for No Bus:b43-phy0::rx
[ 63.983997] PM: Removing info for No Bus:b43-phy0::radio
[ 63.984046] b43-phy0 debug: DMA-32 rx_ring: Used slots 0/64, Failed frames
0/0 = 0.0%, Average tries 0.00
[ 63.984087] b43-phy0 debug: DMA-32 tx_ring_AC_BK: Used slots 0/128, Failed
frames 0/0 = 0.0%, Average tries 0.00
[ 63.991862] b43-phy0 debug: DMA-32 tx_ring_AC_BE: Used slots 0/128, Failed
frames 0/0 = 0.0%, Average tries 0.00
[ 63.999852] b43-phy0 debug: DMA-32 tx_ring_AC_VI: Used slots 0/128, Failed
frames 0/0 = 0.0%, Average tries 0.00
[ 64.007844] b43-phy0 debug: DMA-32 tx_ring_AC_VO: Used slots 2/128, Failed
frames 0/13 = 0.0%, Average tries 1.00
[ 64.015844] b43-phy0 debug: DMA-32 tx_ring_mcast: Used slots 0/128, Failed
frames 0/0 = 0.0%, Average tries 0.00
[ 64.183858] b43-phy0: Loading firmware version 351.126 (2006-07-29 05:54:02)
[ 64.183865] b43-phy0 warning: You are using an old firmware image. Support
for old firmware will be removed in July 2008.
[ 64.183868] b43-phy0 warning: You must go to
http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the
latest firmware (version 4).
[ 65.036186] b43-phy0 debug: Chip initialized
[ 65.036363] b43-phy0 debug: 32-bit DMA initialized
[ 65.056312] PM: Adding info for No Bus:b43-phy0::tx
[ 65.056329] Registered led device: b43-phy0::tx
[ 65.056343] PM: Adding info for No Bus:b43-phy0::rx
[ 65.056355] Registered led device: b43-phy0::rx
[ 65.056367] PM: Adding info for No Bus:b43-phy0::radio
[ 65.056378] Registered led device: b43-phy0::radio
[ 65.056407] b43-phy0 debug: Wireless interface started
[ 65.067969] b43-phy0: Radio hardware status changed to DISABLED
[ 92.361618] b43-phy0 debug: Switching to 5-GHz band
[ 92.361646] b43-phy0 debug: Wireless interface stopped
[ 92.361661] PM: Removing info for No Bus:b43-phy0::tx
[ 92.361716] PM: Removing info for No Bus:b43-phy0::rx
[ 92.361746] PM: Removing info for No Bus:b43-phy0::radio
[ 92.361802] b43-phy0 debug: DMA-32 rx_ring: Used slots 0/64, Failed frames
0/0 = 0.0%, Average tries 0.00
[ 92.361849] b43-phy0 debug: DMA-32 tx_ring_AC_BK: Used slots 0/128, Failed
frames 0/0 = 0.0%, Average tries 0.00
[ 92.369634] b43-phy0 debug: DMA-32 tx_ring_AC_BE: Used slots 0/128, Failed
frames 0/0 = 0.0%, Average tries 0.00
[ 92.377622] b43-phy0 debug: DMA-32 tx_ring_AC_VI: Used slots 0/128, Failed
frames 0/0 = 0.0%, Average tries 0.00
[ 92.385618] b43-phy0 debug: DMA-32 tx_ring_AC_VO: Used slots 2/128, Failed
frames 0/11 = 0.0%, Average tries 1.00
[ 92.393619] b43-phy0 debug: DMA-32 tx_ring_mcast: Used slots 0/128, Failed
frames 0/0 = 0.0%, Average tries 0.00
[ 92.561632] b43-phy0: Loading firmware version 351.126 (2006-07-29 05:54:02)
[ 92.561642] b43-phy0 warning: You are using an old firmware image. Support
for old firmware will be removed in July 2008.
[ 92.561646] b43-phy0 warning: You must go to
http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the
latest firmware (version 4).
[ 93.277729] b43-phy0 debug: Chip initialized
[ 93.277927] b43-phy0 debug: 32-bit DMA initialized
[ 93.297910] PM: Adding info for No Bus:b43-phy0::tx
[ 93.297933] Registered led device: b43-phy0::tx
[ 93.297944] PM: Adding info for No Bus:b43-phy0::rx
[ 93.297958] Registered led device: b43-phy0::rx
[ 93.297968] PM: Adding info for No Bus:b43-phy0::radio
[ 93.297981] Registered led device: b43-phy0::radio
[ 93.298001] b43-phy0 debug: Wireless interface started
[ 93.298026] b43-phy0 ERROR: PHY transmission error
[ 93.337750] b43-phy0 ERROR: PHY transmission error
[ 93.395064] b43-phy0: Radio hardware status changed to DISABLED
[ 94.037744] b43-phy0 debug: Switching to 2.4-GHz band
[ 94.037778] b43-phy0 debug: Wireless interface stopped
[ 94.037792] PM: Removing info for No Bus:b43-phy0::tx
[ 94.037857] PM: Removing info for No Bus:b43-phy0::rx
[ 94.037887] PM: Removing info for No Bus:b43-phy0::radio
[ 94.037940] b43-phy0 debug: DMA-32 rx_ring: Used slots 0/64, Failed frames
0/0 = 0.0%, Average tries 0.00
[ 94.037989] b43-phy0 debug: DMA-32 tx_ring_AC_BK: Used slots 0/128, Failed
frames 0/0 = 0.0%, Average tries 0.00
[ 94.045865] b43-phy0 debug: DMA-32 tx_ring_AC_BE: Used slots 0/128, Failed
frames 0/0 = 0.0%, Average tries 0.00
[ 94.053729] b43-phy0 debug: DMA-32 tx_ring_AC_VI: Used slots 0/128, Failed
frames 0/0 = 0.0%, Average tries 0.00
[ 94.061723] b43-phy0 debug: DMA-32 tx_ring_AC_VO: Used slots 2/128, Failed
frames 0/13 = 0.0%, Average tries 1.00
[ 94.069727] b43-phy0 debug: DMA-32 tx_ring_mcast: Used slots 0/128, Failed
frames 0/0 = 0.0%, Average tries 0.00
[ 94.237739] b43-phy0: Loading firmware version 351.126 (2006-07-29 05:54:02)
[ 94.237748] b43-phy0 warning: You are using an old firmware image. Support
for old firmware will be removed in July 2008.
[ 94.237752] b43-phy0 warning: You must go to
http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the
latest firmware (version 4).
[ 95.113931] b43-phy0 debug: Chip initialized
[ 95.114110] b43-phy0 debug: 32-bit DMA initialized
[ 95.134028] PM: Adding info for No Bus:b43-phy0::tx
[ 95.134048] Registered led device: b43-phy0::tx
[ 95.134059] PM: Adding info for No Bus:b43-phy0::rx
[ 95.134072] Registered led device: b43-phy0::rx
[ 95.134084] PM: Adding info for No Bus:b43-phy0::radio
[ 95.134099] Registered led device: b43-phy0::radio
[ 95.134123] b43-phy0 debug: Wireless interface started
[ 95.185934] b43-phy0: Radio hardware status changed to DISABLED
[ 122.411500] b43-phy0 debug: Switching to 5-GHz band
[ 122.411532] b43-phy0 debug: Wireless interface stopped
[ 122.411545] PM: Removing info for No Bus:b43-phy0::tx
[ 122.411600] PM: Removing info for No Bus:b43-phy0::rx
[ 122.411630] PM: Removing info for No Bus:b43-phy0::radio
[ 122.411683] b43-phy0 debug: DMA-32 rx_ring: Used slots 0/64, Failed frames
0/0 = 0.0%, Average tries 0.00
[ 122.411732] b43-phy0 debug: DMA-32 tx_ring_AC_BK: Used slots 0/128, Failed
frames 0/0 = 0.0%, Average tries 0.00
[ 122.419499] b43-phy0 debug: DMA-32 tx_ring_AC_BE: Used slots 0/128, Failed
frames 0/0 = 0.0%, Average tries 0.00
[ 122.427497] b43-phy0 debug: DMA-32 tx_ring_AC_VI: Used slots 0/128, Failed
frames 0/0 = 0.0%, Average tries 0.00
[ 122.435503] b43-phy0 debug: DMA-32 tx_ring_AC_VO: Used slots 16/128, Failed
frames 0/11 = 0.0%, Average tries 0.45
[ 122.443506] b43-phy0 debug: DMA-32 tx_ring_mcast: Used slots 0/128, Failed
frames 0/0 = 0.0%, Average tries 0.00
[ 122.611518] b43-phy0: Loading firmware version 351.126 (2006-07-29 05:54:02)
[ 122.611530] b43-phy0 warning: You are using an old firmware image. Support
for old firmware will be removed in July 2008.
[ 122.611534] b43-phy0 warning: You must go to
http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the
latest firmware (version 4).
[ 123.327607] b43-phy0 debug: Chip initialized
[ 123.327785] b43-phy0 debug: 32-bit DMA initialized
[ 123.347788] PM: Adding info for No Bus:b43-phy0::tx
[ 123.347810] Registered led device: b43-phy0::tx
[ 123.347822] PM: Adding info for No Bus:b43-phy0::rx
[ 123.347835] Registered led device: b43-phy0::rx
[ 123.347847] PM: Adding info for No Bus:b43-phy0::radio
[ 123.347860] Registered led device: b43-phy0::radio
[ 123.347883] b43-phy0 debug: Wireless interface started
[ 123.347910] b43-phy0 ERROR: PHY transmission error
[ 123.387621] b43-phy0 ERROR: PHY transmission error
[ 123.387653] b43-phy0: Radio hardware status changed to DISABLED
[ 124.091629] b43-phy0 debug: Switching to 2.4-GHz band
[ 124.091654] b43-phy0 debug: Wireless interface stopped
[ 124.091670] PM: Removing info for No Bus:b43-phy0::tx
[ 124.091736] PM: Removing info for No Bus:b43-phy0::rx
[ 124.091770] PM: Removing info for No Bus:b43-phy0::radio
[ 124.091824] b43-phy0 debug: DMA-32 rx_ring: Used slots 0/64, Failed frames
0/0 = 0.0%, Average tries 0.00
[ 124.091865] b43-phy0 debug: DMA-32 tx_ring_AC_BK: Used slots 0/128, Failed
frames 0/0 = 0.0%, Average tries 0.00
[ 124.099602] b43-phy0 debug: DMA-32 tx_ring_AC_BE: Used slots 0/128, Failed
frames 0/0 = 0.0%, Average tries 0.00
[ 124.107606] b43-phy0 debug: DMA-32 tx_ring_AC_VI: Used slots 0/128, Failed
frames 0/0 = 0.0%, Average tries 0.00
[ 124.115602] b43-phy0 debug: DMA-32 tx_ring_AC_VO: Used slots 2/128, Failed
frames 0/13 = 0.0%, Average tries 1.00
[ 124.123604] b43-phy0 debug: DMA-32 tx_ring_mcast: Used slots 0/128, Failed
frames 0/0 = 0.0%, Average tries 0.00
[ 124.291619] b43-phy0: Loading firmware version 351.126 (2006-07-29 05:54:02)
[ 124.291630] b43-phy0 warning: You are using an old firmware image. Support
for old firmware will be removed in July 2008.
[ 124.291634] b43-phy0 warning: You must go to
http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the
latest firmware (version 4).
[ 125.435963] b43-phy0 debug: Chip initialized
[ 125.436163] b43-phy0 debug: 32-bit DMA initialized
[ 125.456094] PM: Adding info for No Bus:b43-phy0::tx
[ 125.456112] Registered led device: b43-phy0::tx
[ 125.456124] PM: Adding info for No Bus:b43-phy0::rx
[ 125.456137] Registered led device: b43-phy0::rx
[ 125.456148] PM: Adding info for No Bus:b43-phy0::radio
[ 125.456160] Registered led device: b43-phy0::radio
[ 125.456191] b43-phy0 debug: Wireless interface started
[ 125.507982] b43-phy0: Radio hardware status changed to DISABLED
[ 152.449374] b43-phy0 debug: Switching to 5-GHz band
[ 152.449400] b43-phy0 debug: Wireless interface stopped
[ 152.449415] PM: Removing info for No Bus:b43-phy0::tx
[ 152.449477] PM: Removing info for No Bus:b43-phy0::rx
[ 152.449506] PM: Removing info for No Bus:b43-phy0::radio
[ 152.449560] b43-phy0 debug: DMA-32 rx_ring: Used slots 0/64, Failed frames
0/0 = 0.0%, Average tries 0.00
[ 152.449607] b43-phy0 debug: DMA-32 tx_ring_AC_BK: Used slots 0/128, Failed
frames 0/0 = 0.0%, Average tries 0.00
[ 152.457514] b43-phy0 debug: DMA-32 tx_ring_AC_BE: Used slots 0/128, Failed
frames 0/0 = 0.0%, Average tries 0.00
[ 152.465380] b43-phy0 debug: DMA-32 tx_ring_AC_VI: Used slots 0/128, Failed
frames 0/0 = 0.0%, Average tries 0.00
[ 152.473391] b43-phy0 debug: DMA-32 tx_ring_AC_VO: Used slots 2/128, Failed
frames 0/11 = 0.0%, Average tries 1.00
[ 152.481384] b43-phy0 debug: DMA-32 tx_ring_mcast: Used slots 0/128, Failed
frames 0/0 = 0.0%, Average tries 0.00
[ 152.649390] b43-phy0: Loading firmware version 351.126 (2006-07-29 05:54:02)
[ 152.649401] b43-phy0 warning: You are using an old firmware image. Support
for old firmware will be removed in July 2008.
[ 152.649406] b43-phy0 warning: You must go to
http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the
latest firmware (version 4).
[ 153.413491] b43-phy0 debug: Chip initialized
[ 153.413653] b43-phy0 debug: 32-bit DMA initialized
[ 153.433672] PM: Adding info for No Bus:b43-phy0::tx
[ 153.433692] Registered led device: b43-phy0::tx
[ 153.433703] PM: Adding info for No Bus:b43-phy0::rx
[ 153.433720] Registered led device: b43-phy0::rx
[ 153.433732] PM: Adding info for No Bus:b43-phy0::radio
[ 153.433743] Registered led device: b43-phy0::radio
[ 153.433766] b43-phy0 debug: Wireless interface started
[ 153.433791] b43-phy0 ERROR: PHY transmission error
[ 153.485528] b43-phy0 ERROR: PHY transmission error
[ 153.485849] b43-phy0: Radio hardware status changed to DISABLED
[ 154.189497] b43-phy0 debug: Switching to 2.4-GHz band
[ 154.189554] b43-phy0 debug: Wireless interface stopped
[ 154.189569] PM: Removing info for No Bus:b43-phy0::tx
[ 154.189635] PM: Removing info for No Bus:b43-phy0::rx
[ 154.189665] PM: Removing info for No Bus:b43-phy0::radio
[ 154.189719] b43-phy0 debug: DMA-32 rx_ring: Used slots 0/64, Failed frames
0/0 = 0.0%, Average tries 0.00
[ 154.189766] b43-phy0 debug: DMA-32 tx_ring_AC_BK: Used slots 0/128, Failed
frames 0/0 = 0.0%, Average tries 0.00
[ 154.197486] b43-phy0 debug: DMA-32 tx_ring_AC_BE: Used slots 0/128, Failed
frames 0/0 = 0.0%, Average tries 0.00
[ 154.205482] b43-phy0 debug: DMA-32 tx_ring_AC_VI: Used slots 0/128, Failed
frames 0/0 = 0.0%, Average tries 0.00
[ 154.213482] b43-phy0 debug: DMA-32 tx_ring_AC_VO: Used slots 2/128, Failed
frames 0/13 = 0.0%, Average tries 1.00
[ 154.221490] b43-phy0 debug: DMA-32 tx_ring_mcast: Used slots 0/128, Failed
frames 0/0 = 0.0%, Average tries 0.00
[ 154.389508] b43-phy0: Loading firmware version 351.126 (2006-07-29 05:54:02)
[ 154.389518] b43-phy0 warning: You are using an old firmware image. Support
for old firmware will be removed in July 2008.
[ 154.389523] b43-phy0 warning: You must go to
http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the
latest firmware (version 4).
[ 155.397846] b43-phy0 debug: Chip initialized
[ 155.398032] b43-phy0 debug: 32-bit DMA initialized
[ 155.417961] PM: Adding info for No Bus:b43-phy0::tx
[ 155.417981] Registered led device: b43-phy0::tx
[ 155.417993] PM: Adding info for No Bus:b43-phy0::rx
[ 155.418006] Registered led device: b43-phy0::rx
[ 155.418018] PM: Adding info for No Bus:b43-phy0::radio
[ 155.418030] Registered led device: b43-phy0::radio
[ 155.418061] b43-phy0 debug: Wireless interface started
[ 155.469856] b43-phy0: Radio hardware status changed to DISABLED
[ 262.828291] b43-phy0: Radio hardware status changed to ENABLED
[ 264.832448] b43-phy0: Radio hardware status changed to DISABLED
[ 281.773455] b43-phy0: Radio turned on by software
[ 281.773463] b43-phy0: The hardware RF-kill button still turns the radio
physically off. Press the button to turn it on.
[ 282.509502] b43-phy0 debug: Switching to 5-GHz band
[ 282.509532] b43-phy0 debug: Wireless interface stopped
[ 282.509548] PM: Removing info for No Bus:b43-phy0::tx
[ 282.509604] PM: Removing info for No Bus:b43-phy0::rx
[ 282.509634] PM: Removing info for No Bus:b43-phy0::radio
[ 282.509688] b43-phy0 debug: DMA-32 rx_ring: Used slots 0/64, Failed frames
0/0 = 0.0%, Average tries 0.00
[ 282.509735] b43-phy0 debug: DMA-32 tx_ring_AC_BK: Used slots 0/128, Failed
frames 0/0 = 0.0%, Average tries 0.00
[ 282.517516] b43-phy0 debug: DMA-32 tx_ring_AC_BE: Used slots 0/128, Failed
frames 0/0 = 0.0%, Average tries 0.00
[ 282.525557] b43-phy0 debug: DMA-32 tx_ring_AC_VI: Used slots 0/128, Failed
frames 0/0 = 0.0%, Average tries 0.00
[ 282.533502] b43-phy0 debug: DMA-32 tx_ring_AC_VO: Used slots 4/128, Failed
frames 0/11 = 0.0%, Average tries 0.90
[ 282.541502] b43-phy0 debug: DMA-32 tx_ring_mcast: Used slots 0/128, Failed
frames 0/0 = 0.0%, Average tries 0.00
[ 282.709517] b43-phy0: Loading firmware version 351.126 (2006-07-29 05:54:02)
[ 282.709526] b43-phy0 warning: You are using an old firmware image. Support
for old firmware will be removed in July 2008.
[ 282.709530] b43-phy0 warning: You must go to
http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the
latest firmware (version 4).
[ 283.465615] b43-phy0 debug: Chip initialized
[ 283.465791] b43-phy0 debug: 32-bit DMA initialized
[ 283.485799] PM: Adding info for No Bus:b43-phy0::tx
[ 283.485819] Registered led device: b43-phy0::tx
[ 283.485830] PM: Adding info for No Bus:b43-phy0::rx
[ 283.485843] Registered led device: b43-phy0::rx
[ 283.485855] PM: Adding info for No Bus:b43-phy0::radio
[ 283.485870] Registered led device: b43-phy0::radio
[ 283.485892] b43-phy0 debug: Wireless interface started
[ 283.485917] b43-phy0 ERROR: PHY transmission error
[ 283.518327] b43-phy0 ERROR: PHY transmission error
[ 283.518399] b43-phy0 ERROR: PHY transmission error
[ 283.518412] b43-phy0 ERROR: PHY transmission error
[ 283.518421] b43-phy0 ERROR: PHY transmission error
[ 283.518437] b43-phy0 ERROR: PHY transmission error
[ 283.518448] b43-phy0 ERROR: PHY transmission error
[ 283.518457] b43-phy0 ERROR: PHY transmission error
[ 284.225616] b43-phy0 debug: Switching to 2.4-GHz band
[ 284.225653] b43-phy0 debug: Wireless interface stopped
[ 284.225667] PM: Removing info for No Bus:b43-phy0::tx
[ 284.225733] PM: Removing info for No Bus:b43-phy0::rx
[ 284.225762] PM: Removing info for No Bus:b43-phy0::radio
[ 284.225817] b43-phy0 debug: DMA-32 rx_ring: Used slots 0/64, Failed frames
0/0 = 0.0%, Average tries 0.00
[ 284.225863] b43-phy0 debug: DMA-32 tx_ring_AC_BK: Used slots 0/128, Failed
frames 0/0 = 0.0%, Average tries 0.00
[ 284.234433] b43-phy0 debug: DMA-32 tx_ring_AC_BE: Used slots 0/128, Failed
frames 0/0 = 0.0%, Average tries 0.00
[ 284.241614] b43-phy0 debug: DMA-32 tx_ring_AC_VI: Used slots 0/128, Failed
frames 0/0 = 0.0%, Average tries 0.00
[ 284.249609] b43-phy0 debug: DMA-32 tx_ring_AC_VO: Used slots 2/128, Failed
frames 0/13 = 0.0%, Average tries 1.00
[ 284.257610] b43-phy0 debug: DMA-32 tx_ring_mcast: Used slots 0/128, Failed
frames 0/0 = 0.0%, Average tries 0.00
[ 284.425623] b43-phy0: Loading firmware version 351.126 (2006-07-29 05:54:02)
[ 284.425631] b43-phy0 warning: You are using an old firmware image. Support
for old firmware will be removed in July 2008.
[ 284.425635] b43-phy0 warning: You must go to
http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the
latest firmware (version 4).
[ 285.345822] b43-phy0 debug: Chip initialized
[ 285.346014] b43-phy0 debug: 32-bit DMA initialized
[ 285.365917] PM: Adding info for No Bus:b43-phy0::tx
[ 285.365936] Registered led device: b43-phy0::tx
[ 285.365948] PM: Adding info for No Bus:b43-phy0::rx
[ 285.365964] Registered led device: b43-phy0::rx
[ 285.365975] PM: Adding info for No Bus:b43-phy0::radio
[ 285.365988] Registered led device: b43-phy0::radio
[ 285.366011] b43-phy0 debug: Wireless interface started
[ 412.521630] b43-phy0 debug: Switching to 5-GHz band
[ 412.521661] b43-phy0 debug: Wireless interface stopped
[ 412.521677] PM: Removing info for No Bus:b43-phy0::tx
[ 412.521737] PM: Removing info for No Bus:b43-phy0::rx
[ 412.521769] PM: Removing info for No Bus:b43-phy0::radio
[ 412.521823] b43-phy0 debug: DMA-32 rx_ring: Used slots 0/64, Failed frames
0/0 = 0.0%, Average tries 0.00
[ 412.521872] b43-phy0 debug: DMA-32 tx_ring_AC_BK: Used slots 0/128, Failed
frames 0/0 = 0.0%, Average tries 0.00
[ 412.529841] b43-phy0 debug: DMA-32 tx_ring_AC_BE: Used slots 0/128, Failed
frames 0/0 = 0.0%, Average tries 0.00
[ 412.537639] b43-phy0 debug: DMA-32 tx_ring_AC_VI: Used slots 0/128, Failed
frames 0/0 = 0.0%, Average tries 0.00
[ 412.545629] b43-phy0 debug: DMA-32 tx_ring_AC_VO: Used slots 4/128, Failed
frames 0/11 = 0.0%, Average tries 1.00
[ 412.553629] b43-phy0 debug: DMA-32 tx_ring_mcast: Used slots 0/128, Failed
frames 0/0 = 0.0%, Average tries 0.00
[ 412.721645] b43-phy0: Loading firmware version 351.126 (2006-07-29 05:54:02)
[ 412.721656] b43-phy0 warning: You are using an old firmware image. Support
for old firmware will be removed in July 2008.
[ 412.721661] b43-phy0 warning: You must go to
http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the
latest firmware (version 4).
[ 413.493782] b43-phy0 debug: Chip initialized
[ 413.493953] b43-phy0 debug: 32-bit DMA initialized
[ 413.513924] PM: Adding info for No Bus:b43-phy0::tx
[ 413.513943] Registered led device: b43-phy0::tx
[ 413.513955] PM: Adding info for No Bus:b43-phy0::rx
[ 413.513967] Registered led device: b43-phy0::rx
[ 413.513979] PM: Adding info for No Bus:b43-phy0::radio
[ 413.513990] Registered led device: b43-phy0::radio
[ 413.514015] b43-phy0 debug: Wireless interface started
[ 413.514045] b43-phy0 ERROR: PHY transmission error
[ 413.553755] b43-phy0 ERROR: PHY transmission error
[ 413.553792] b43-phy0: Radio hardware status changed to DISABLED
[ 414.253750] b43-phy0 debug: Switching to 2.4-GHz band
[ 414.253783] b43-phy0 debug: Wireless interface stopped
[ 414.253798] PM: Removing info for No Bus:b43-phy0::tx
[ 414.254342] PM: Removing info for No Bus:b43-phy0::rx
[ 414.254377] PM: Removing info for No Bus:b43-phy0::radio
[ 414.254433] b43-phy0 debug: DMA-32 rx_ring: Used slots 0/64, Failed frames
0/0 = 0.0%, Average tries 0.00
[ 414.254481] b43-phy0 debug: DMA-32 tx_ring_AC_BK: Used slots 0/128, Failed
frames 0/0 = 0.0%, Average tries 0.00
[ 414.261745] b43-phy0 debug: DMA-32 tx_ring_AC_BE: Used slots 0/128, Failed
frames 0/0 = 0.0%, Average tries 0.00
[ 414.269734] b43-phy0 debug: DMA-32 tx_ring_AC_VI: Used slots 0/128, Failed
frames 0/0 = 0.0%, Average tries 0.00
[ 414.277736] b43-phy0 debug: DMA-32 tx_ring_AC_VO: Used slots 2/128, Failed
frames 0/13 = 0.0%, Average tries 1.00
[ 414.285754] b43-phy0 debug: DMA-32 tx_ring_mcast: Used slots 0/128, Failed
frames 0/0 = 0.0%, Average tries 0.00
[ 414.453753] b43-phy0: Loading firmware version 351.126 (2006-07-29 05:54:02)
[ 414.453761] b43-phy0 warning: You are using an old firmware image. Support
for old firmware will be removed in July 2008.
[ 414.453765] b43-phy0 warning: You must go to
http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the
latest firmware (version 4).
[ 415.334091] b43-phy0 debug: Chip initialized
[ 415.334285] b43-phy0 debug: 32-bit DMA initialized
[ 415.354205] PM: Adding info for No Bus:b43-phy0::tx
[ 415.354226] Registered led device: b43-phy0::tx
[ 415.354238] PM: Adding info for No Bus:b43-phy0::rx
[ 415.354255] Registered led device: b43-phy0::rx
[ 415.354266] PM: Adding info for No Bus:b43-phy0::radio
[ 415.354278] Registered led device: b43-phy0::radio
[ 415.354310] b43-phy0 debug: Wireless interface started
[ 415.365857] b43-phy0: Radio hardware status changed to DISABLED
[ 542.565758] b43-phy0 debug: Switching to 5-GHz band
[ 542.565784] b43-phy0 debug: Wireless interface stopped
[ 542.565800] PM: Removing info for No Bus:b43-phy0::tx
[ 542.565858] PM: Removing info for No Bus:b43-phy0::rx
[ 542.565887] PM: Removing info for No Bus:b43-phy0::radio
[ 542.565941] b43-phy0 debug: DMA-32 rx_ring: Used slots 0/64, Failed frames
0/0 = 0.0%, Average tries 0.00
[ 542.565994] b43-phy0 debug: DMA-32 tx_ring_AC_BK: Used slots 0/128, Failed
frames 0/0 = 0.0%, Average tries 0.00
[ 542.573766] b43-phy0 debug: DMA-32 tx_ring_AC_BE: Used slots 0/128, Failed
frames 0/0 = 0.0%, Average tries 0.00
[ 542.581757] b43-phy0 debug: DMA-32 tx_ring_AC_VI: Used slots 0/128, Failed
frames 0/0 = 0.0%, Average tries 0.00
[ 542.589754] b43-phy0 debug: DMA-32 tx_ring_AC_VO: Used slots 18/128, Failed
frames 0/11 = 0.0%, Average tries 0.36
[ 542.597784] b43-phy0 debug: DMA-32 tx_ring_mcast: Used slots 0/128, Failed
frames 0/0 = 0.0%, Average tries 0.00
[ 542.765772] b43-phy0: Loading firmware version 351.126 (2006-07-29 05:54:02)
[ 542.765782] b43-phy0 warning: You are using an old firmware image. Support
for old firmware will be removed in July 2008.
[ 542.765786] b43-phy0 warning: You must go to
http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the
latest firmware (version 4).
[ 543.526030] b43-phy0 debug: Chip initialized
[ 543.526975] b43-phy0 debug: 32-bit DMA initialized
[ 543.546959] PM: Adding info for No Bus:b43-phy0::tx
[ 543.546978] Registered led device: b43-phy0::tx
[ 543.546990] PM: Adding info for No Bus:b43-phy0::rx
[ 543.547003] Registered led device: b43-phy0::rx
[ 543.547015] PM: Adding info for No Bus:b43-phy0::radio
[ 543.547027] Registered led device: b43-phy0::radio
[ 543.547058] b43-phy0 debug: Wireless interface started
[ 543.547092] b43-phy0 ERROR: PHY transmission error
[ 543.585946] b43-phy0 ERROR: PHY transmission error
[ 543.585989] b43-phy0: Radio hardware status changed to DISABLED
[ 544.285876] b43-phy0 debug: Switching to 2.4-GHz band
[ 544.285930] b43-phy0 debug: Wireless interface stopped
[ 544.285945] PM: Removing info for No Bus:b43-phy0::tx
[ 544.286011] PM: Removing info for No Bus:b43-phy0::rx
[ 544.286044] PM: Removing info for No Bus:b43-phy0::radio
[ 544.286097] b43-phy0 debug: DMA-32 rx_ring: Used slots 0/64, Failed frames
0/0 = 0.0%, Average tries 0.00
[ 544.286146] b43-phy0 debug: DMA-32 tx_ring_AC_BK: Used slots 0/128, Failed
frames 0/0 = 0.0%, Average tries 0.00
[ 544.293902] b43-phy0 debug: DMA-32 tx_ring_AC_BE: Used slots 0/128, Failed
frames 0/0 = 0.0%, Average tries 0.00
[ 544.301861] b43-phy0 debug: DMA-32 tx_ring_AC_VI: Used slots 0/128, Failed
frames 0/0 = 0.0%, Average tries 0.00
[ 544.309861] b43-phy0 debug: DMA-32 tx_ring_AC_VO: Used slots 2/128, Failed
frames 0/13 = 0.0%, Average tries 1.00
[ 544.318605] b43-phy0 debug: DMA-32 tx_ring_mcast: Used slots 0/128, Failed
frames 0/0 = 0.0%, Average tries 0.00
[ 544.485878] b43-phy0: Loading firmware version 351.126 (2006-07-29 05:54:02)
[ 544.485886] b43-phy0 warning: You are using an old firmware image. Support
for old firmware will be removed in July 2008.
[ 544.485890] b43-phy0 warning: You must go to
http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the
latest firmware (version 4).
[ 545.370242] b43-phy0 debug: Chip initialized
[ 545.370435] b43-phy0 debug: 32-bit DMA initialized
[ 545.390337] PM: Adding info for No Bus:b43-phy0::tx
[ 545.390356] Registered led device: b43-phy0::tx
[ 545.390367] PM: Adding info for No Bus:b43-phy0::rx
[ 545.390383] Registered led device: b43-phy0::rx
[ 545.390395] PM: Adding info for No Bus:b43-phy0::radio
[ 545.390408] Registered led device: b43-phy0::radio
[ 545.390438] b43-phy0 debug: Wireless interface started
[ 545.442214] b43-phy0: Radio hardware status changed to DISABLED
_______________________________________________
Bcm43xx-dev mailing list
[email protected]
https://lists.berlios.de/mailman/listinfo/bcm43xx-dev
