Hello,
my b43 driver is not working for me, but it was, i dont remember, maybe
after the kernel upgrade or sth it stopped working, well it actually works,
i can search for networks, associate with them, but after few seconds or
minutes (usually when i try to access some web page) it disconnects. I dont
understand why.
I searched in forums and mailing lists for weeks and nothing helpes,
compiled kernel manualy and nothing, im in deep depression becouse of this.
below info about my system:
uname -a
Linux myhost 2.6.26-ARCH #1 SMP PREEMPT Tue Sep 9 10:15:21 UTC 2008 i686
Mobile AMD Sempron(tm) Processor 3500+ AuthenticAMD GNU/Linux
lspci -vvnn
05:00.0 Network controller [0280]: Broadcom Corporation BCM4311 802.11b/g
WLAN [14e4:4311] (rev 01)
Subsystem: Dell Wireless 1390 WLAN Mini-Card [1028:0007]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at c0200000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
Capabilities: [58] Message Signalled Interrupts: Mask- 64bit- Queue=0/0
Enable-
Address: 00000000 Data: 0000
Capabilities: [d0] Express (v1) Legacy Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <4us, L1
unlimited
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr-
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s, Latency L0
<4us, L1 <64us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive-
BWMgmt- ABWMgmt-
Capabilities: [100] Advanced Error Reporting <?>
Capabilities: [13c] Virtual Channel <?>
Kernel driver in use: b43-pci-bridge
Kernel modules: ssb
dmesg
after ifconfig wlan0 up
input: b43-phy0 as /class/input/input8
firmware: requesting b43/ucode5.fw
firmware: requesting b43/pcm5.fw
firmware: requesting b43/b0g0initvals5.fw
firmware: requesting b43/b0g0bsinitvals5.fw
b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
Registered led device: b43-phy0::tx
Registered led device: b43-phy0::rx
Registered led device: b43-phy0::radio
after iwconfig wlan0 essid AAAAAAA key s:LALALALALA && dhcpcd wlan0
wlan0: Initial auth_alg=0
wlan0: authenticate with AP 00:18:e7:32:a0:a4
wlan0: RX authentication from 00:18:e7:32:a0:a4 (alg=0 transaction=2
status=0)
wlan0: authenticated
wlan0: associate with AP 00:18:e7:32:a0:a4
wlan0: RX AssocResp from 00:18:e7:32:a0:a4 (capab=0x411 status=0 aid=2)
wlan0: invalid aid value 2; bits 15:14 not set
wlan0: associated
wlan0: switched to short barker preamble (BSSID=00:18:e7:32:a0:a4)
wlan0: switched to long barker preamble (BSSID=00:18:e7:32:a0:a4)
process `skype' is using obsolete setsockopt SO_BSDCOMPAT
hda-intel: Invalid position buffer, using LPIB read method instead.
b43-phy0 ERROR: PHY transmission error
wlan0: No ProbeResp from current AP 00:18:e7:32:a0:a4 - assume out of range
_______________________________________________
Bcm43xx-dev mailing list
[email protected]
https://lists.berlios.de/mailman/listinfo/bcm43xx-dev
