Hi,
as I got comparable problems after upgrading the firmware, I attach the
mail I sent a while ago (to Debian bugs). The mail never appeared
on the list here (I was not supscribed).
I confirmed this in the meantime with a more recent Debian kernel
(2.6.26) and got one response from a guy with the same
symptoms. Downgrading the firmware helped him too.
Regards,
Andi
Bug#480053: b43-phy0 ERROR: PHY transmission error with firmware
version 410.2160
Andreas B. Mundt
Sun, 06 Jul 2008 00:26:13 -0700
Hi,
I already sent this message to [EMAIL PROTECTED], but got no
response yet. With the transition to 2.6.25 in testing it might be
important:
Using firmware version 410.2160 results in massive problems with my
wlan card. The connection is established (WEP), but fails sooner or
later
(usually after a couple of seconds or minutes, not immediately, during
data transfer: 'b43-phy0 ERROR: PHY transmission error').
The card worked fine with firmware version 351.126.
Please find some more information below. If I can be of any help, let
me know. Thanks,
Andi
Debian Lenny:
[EMAIL PROTECTED]:~$ uname -a
Linux flashgordon 2.6.25-2-amd64 #1 SMP Fri Jun 27 00:16:12 UTC 2008
x86_64 GNU/Linux
[EMAIL PROTECTED]:~$ lspci -vvn|grep 43 -A7
01:08.0 0280: 14e4:4318 (rev 02)
Subsystem: 14e4:7001
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fb004000 (32-bit, non-prefetchable)
[size=8K]
Kernel driver in use: b43-pci-bridge
Kernel modules: ssb
01:0a.0 0c00: 104c:8024 (prog-if 10)
Subsystem: 1458:1000
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (750ns min, 1000ns max), Cache Line Size: 32 bytes
The firmware version 410.2160 has been downloaded, module b43 removed
and inserted again.
dmesg part with failing firmware version 410.2160:
----------
[ 3817.687997] ACPI: PCI interrupt for device 0000:01:08.0 disabled
[ 4052.495588] ACPI: PCI Interrupt 0000:01:08.0[A] -> Link [APC1] ->
GSI 16
(level, low) -> IRQ 16
[ 4052.560232] ssb: Sonics Silicon Backplane found on PCI device
0000:01:08.0
[ 4052.572419] b43-phy0: Broadcom 4318 WLAN found
[ 4052.651154] phy0: Selected rate control algorithm 'pid'
[ 4052.652397] Broadcom 43xx driver loaded [ Features: PMLR,
Firmware-ID: FW13 ]
[ 4112.217051] input: b43-phy0 as /class/input/input7
[ 3887.314665] b43-phy0: Loading firmware version 410.2160 (2007-05-26
15:32:10)
[ 3888.324430] Registered led device: b43-phy0::tx
[ 3888.324430] Registered led device: b43-phy0::rx
[ 3888.324430] Registered led device: b43-phy0::radio
[ 3888.393755] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 3888.623488] eth2: no link during initialization.
[ 3888.624715] ADDRCONF(NETDEV_UP): eth2: link is not ready
[ 3889.176721] input: b43-phy0 as /class/input/input8
[ 3889.405430] b43-phy0: Loading firmware version 410.2160 (2007-05-26
15:32:10)
[ 3890.411913] Registered led device: b43-phy0::tx
[ 3890.411913] Registered led device: b43-phy0::rx
[ 3890.411913] Registered led device: b43-phy0::radio
[ 3890.471954] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 3891.257253] wlan0: Initial auth_alg=0
[ 3891.257253] wlan0: authenticate with AP 00:13:49:b1:2e:1c
[ 4116.743204] wlan0: RX authentication from 00:13:49:b1:2e:1c (alg=0
transaction=2 status=0)
[ 4116.743204] wlan0: authenticated
[ 4116.743204] wlan0: associate with AP 00:13:49:b1:2e:1c
[ 4116.744686] wlan0: authentication frame received from
00:13:49:b1:2e:1c, but
not in authenticate state - ignored
[ 4116.747697] wlan0: authentication frame received from
00:13:49:b1:2e:1c, but
not in authenticate state - ignored
[ 4116.749176] wlan0: authentication frame received from
00:13:49:b1:2e:1c, but
not in authenticate state - ignored
[ 4116.749561] wlan0: RX AssocResp from 00:13:49:b1:2e:1c (capab=0x411
status=0
aid=1)
[ 4116.749561] wlan0: associated
[ 4116.751080] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 4116.842159] wlan0: switched to short barker preamble
(BSSID=00:13:49:b1:2e:1c)
[ 4118.175391] b43-phy0 ERROR: PHY transmission error
[ 4127.705029] wlan0: no IPv6 routers present
[ 4136.723823] b43-phy0 ERROR: PHY transmission error
[ 4182.694170] wlan0: No ProbeResp from current AP 00:13:49:b1:2e:1c -
assume out of range
_______________________________________________
Bcm43xx-dev mailing list
[email protected]
https://lists.berlios.de/mailman/listinfo/bcm43xx-dev
