On Mon, 19 Oct 2009 16:53:24 -0500
Larry Finger <[email protected]> wrote:
> This set of dmesg outputs was better; however, please set
> CONFIG_B43_DEBUG=y in your configuration and rebuild the kernel.
> Please post the full dmesg for warm and cold reboot.
For a warm boot it is:
cfg80211: Using static regulatory domain info
cfg80211: Regulatory domain: US
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
(5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
cfg80211: Calling CRDA for country: US
b43-phy0: Broadcom 4312 WLAN found (core revision 15)
b43-phy0 debug: Found PHY: Analog 6, Type 5, Revision 1
b43-phy0 debug: Found Radio: Manuf 0x17F, Version 0x2062, Revision 2
phy0: Selected rate control algorithm 'minstrel'
Registered led device: b43-phy0::tx
Registered led device: b43-phy0::rx
Registered led device: b43-phy0::radio
Broadcom 43xx driver loaded [ Features: PMLS, Firmware-ID: FW13 ]
b43 ssb0:0: firmware: requesting b43/ucode15.fw
b43 ssb0:0: firmware: requesting b43/lp0initvals15.fw
b43 ssb0:0: firmware: requesting b43/lp0bsinitvals15.fw
b43-phy0: Loading firmware version 478.104 (2008-07-01 00:50:23)
b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
b43-phy0 debug: RC calib: Failed to switch to channel 7, error = -5
b43-phy0 debug: Chip initialized
b43-phy0 debug: 64-bit DMA initialized
b43-phy0 debug: QoS enabled
b43-phy0 debug: Wireless interface started
b43-phy0 debug: Adding Interface type 2
b43-phy0 debug: Removing Interface type 2
b43-phy0 debug: Wireless interface stopped
b43-phy0 debug: DMA-64 rx_ring: Used slots 1/64, Failed frames 0/0 = 0.0%,
Average tries 0.00
b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 =
0.0%, Average tries 0.00
b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 =
0.0%, Average tries 0.00
b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 =
0.0%, Average tries 0.00
b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 2/256, Failed frames 0/33 =
0.0%, Average tries 1.00
b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 =
0.0%, Average tries 0.00
b43-phy0: Loading firmware version 478.104 (2008-07-01 00:50:23)
b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
b43-phy0 debug: Chip initialized
b43-phy0 debug: 64-bit DMA initialized
b43-phy0 debug: QoS enabled
b43-phy0 debug: Wireless interface started
b43-phy0 debug: Adding Interface type 2
wlan0: direct probe to AP 00:08:5c:ca:dc:c3 (try 1)
wlan0: direct probe responded
wlan0: authenticate with AP 00:08:5c:ca:dc:c3 (try 1)
wlan0: authenticated
wlan0: associate with AP 00:08:5c:ca:dc:c3 (try 1)
wlan0: RX AssocResp from 00:08:5c:ca:dc:c3 (capab=0x411 status=0 aid=1)
wlan0: associated
For a cold boot it is:
cfg80211: Using static regulatory domain info
cfg80211: Regulatory domain: US
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
(5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
cfg80211: Calling CRDA for country: US
b43-phy0: Broadcom 4312 WLAN found (core revision 15)
b43-phy0 debug: Found PHY: Analog 6, Type 5, Revision 1
b43-phy0 debug: Found Radio: Manuf 0x17F, Version 0x2062, Revision 2
phy0: Selected rate control algorithm 'minstrel'
Registered led device: b43-phy0::tx
Registered led device: b43-phy0::rx
Registered led device: b43-phy0::radio
Broadcom 43xx driver loaded [ Features: PMLS, Firmware-ID: FW13 ]
b43 ssb0:0: firmware: requesting b43/ucode15.fw
b43 ssb0:0: firmware: requesting b43/lp0initvals15.fw
b43 ssb0:0: firmware: requesting b43/lp0bsinitvals15.fw
b43-phy0: Loading firmware version 478.104 (2008-07-01 00:50:23)
b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
b43-phy0 debug: RC calib: Failed to switch to channel 7, error = -5
b43-phy0 debug: Chip initialized
b43-phy0 debug: 64-bit DMA initialized
b43-phy0 debug: QoS enabled
b43-phy0 debug: Wireless interface started
b43-phy0 debug: Adding Interface type 2
b43-phy0 ERROR: Fatal DMA error: 0x00000800, 0x00000000, 0x00000000,
0x00000000, 0x00000000, 0x00000000
b43-phy0: Controller RESET (DMA error) ...
b43-phy0 debug: Wireless interface stopped
b43-phy0 debug: DMA-64 rx_ring: Used slots 1/64, Failed frames 0/0 = 0.0%,
Average tries 0.00
b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 =
0.0%, Average tries 0.00
b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 =
0.0%, Average tries 0.00
b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 =
0.0%, Average tries 0.00
b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 2/256, Failed frames 0/22 =
0.0%, Average tries 1.00
b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 =
0.0%, Average tries 0.00
b43-phy0: Loading firmware version 478.104 (2008-07-01 00:50:23)
b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
b43-phy0 debug: Chip initialized
b43-phy0 debug: 64-bit DMA initialized
b43-phy0 debug: QoS enabled
b43-phy0 debug: Wireless interface started
b43-phy0: Controller restarted
b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000,
0x00000000, 0x00000000, 0x00000000
b43-phy0: Controller RESET (DMA error) ...
b43-phy0 debug: Wireless interface stopped
b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%,
Average tries 0.00
b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 =
0.0%, Average tries 0.00
b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 =
0.0%, Average tries 0.00
b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 =
0.0%, Average tries 0.00
b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 =
0.0%, Average tries 0.00
b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 =
0.0%, Average tries 0.00
b43-phy0: Loading firmware version 478.104 (2008-07-01 00:50:23)
b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
b43-phy0 debug: Chip initialized
b43-phy0 debug: 64-bit DMA initialized
b43-phy0 debug: QoS enabled
b43-phy0 debug: Wireless interface started
b43-phy0: Controller restarted
b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000,
0x00000000, 0x00000000, 0x00000000
b43-phy0: Controller RESET (DMA error) ...
b43-phy0 debug: Wireless interface stopped
b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%,
Average tries 0.00
b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 =
0.0%, Average tries 0.00
b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 =
0.0%, Average tries 0.00
b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 =
0.0%, Average tries 0.00
b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 =
0.0%, Average tries 0.00
b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 =
0.0%, Average tries 0.00
b43-phy0: Loading firmware version 478.104 (2008-07-01 00:50:23)
b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
b43-phy0 debug: Chip initialized
b43-phy0 debug: 64-bit DMA initialized
b43-phy0 debug: QoS enabled
b43-phy0 debug: Wireless interface started
b43-phy0: Controller restarted
b43-phy0 ERROR: Fatal DMA error: 0x00000400, 0x00000000, 0x00000000,
0x00000000, 0x00000000, 0x00000000
b43-phy0: Controller RESET (DMA error) ...
b43-phy0 debug: Wireless interface stopped
b43-phy0 debug: DMA-64 rx_ring: Used slots 0/64, Failed frames 0/0 = 0.0%,
Average tries 0.00
b43-phy0 debug: DMA-64 tx_ring_AC_BK: Used slots 0/256, Failed frames 0/0 =
0.0%, Average tries 0.00
b43-phy0 debug: DMA-64 tx_ring_AC_BE: Used slots 0/256, Failed frames 0/0 =
0.0%, Average tries 0.00
b43-phy0 debug: DMA-64 tx_ring_AC_VI: Used slots 0/256, Failed frames 0/0 =
0.0%, Average tries 0.00
b43-phy0 debug: DMA-64 tx_ring_AC_VO: Used slots 0/256, Failed frames 0/0 =
0.0%, Average tries 0.00
b43-phy0 debug: DMA-64 tx_ring_mcast: Used slots 0/256, Failed frames 0/0 =
0.0%, Average tries 0.00
b43-phy0: Loading firmware version 478.104 (2008-07-01 00:50:23)
b43-phy0 debug: b2062: Using crystal tab entry 19200 kHz.
_______________________________________________
Bcm43xx-dev mailing list
[email protected]
https://lists.berlios.de/mailman/listinfo/bcm43xx-dev
