On Wed, Nov 6, 2013 at 10:39 AM, Robert Nelson <[email protected]> wrote: > On Wed, Nov 6, 2013 at 9:29 AM, Jason Kridner <[email protected]> > wrote: >> Robert, >> >> I'm starting with the kernel at >> http://github.com/beagleboard/kernel/tree/3.12. I've pushed a patched >> version of the tree to http://github.com/beagleboard/linux/tree/3.12. >> >> To build the kernel, I'm using buildroot via >> http://github.com/jadonk/buildroot/tree/latest. >> >> make beaglebone_config >> make >> >> I'm booting the MLO and u-boot.img that are in the buildroot >> output/images. I then try the following: >> >> U-Boot SPL 2013.07 (Oct 30 2013 - 09:44:19) >> musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, >> SoftConn) >> musb-hdrc: MHDRC RTL version 2.0 >> musb-hdrc: setup fifo_mode 4 >> musb-hdrc: 28/31 max ep, 16384/16384 memory >> USB Peripheral mode controller at 47401000 using PIO, IRQ 0 >> musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, >> SoftConn) >> musb-hdrc: MHDRC RTL version 2.0 >> musb-hdrc: setup fifo_mode 4 >> musb-hdrc: 28/31 max ep, 16384/16384 memory >> USB Host mode controller at 47401800 using PIO, IRQ 0 >> OMAP SD/MMC: 0 >> reading args >> spl: error reading image args, err - -1 >> reading u-boot.img >> reading u-boot.img >> >> >> U-Boot 2013.07 (Oct 30 2013 - 09:44:19) >> >> I2C: ready >> DRAM: 512 MiB >> WARNING: Caches not enabled >> NAND: 0 MiB >> MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 >> *** Warning - readenv() failed, using default environment >> >> musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, >> SoftConn) >> musb-hdrc: MHDRC RTL version 2.0 >> musb-hdrc: setup fifo_mode 4 >> musb-hdrc: 28/31 max ep, 16384/16384 memory >> USB Peripheral mode controller at 47401000 using PIO, IRQ 0 >> musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, >> SoftConn) >> musb-hdrc: MHDRC RTL version 2.0 >> musb-hdrc: setup fifo_mode 4 >> musb-hdrc: 28/31 max ep, 16384/16384 memory >> USB Host mode controller at 47401800 using PIO, IRQ 0 >> Net: <ethaddr> not set. Validating first E-fuse MAC >> cpsw, usb_ether >> Hit any key to stop autoboot: 0 >> U-Boot# >> U-Boot# run findfdt >> U-Boot# setenv bootargs console=${console} >> U-Boot# load mmc 0 0x80007fc0 uImage >> reading uImage >> 34759872 bytes read in 3941 ms (8.4 MiB/s) >> U-Boot# load mmc 0 0x82ff8000 ${fdtfile} >> reading am335x-boneblack.dtb >> 18465 bytes read in 9 ms (2 MiB/s) >> U-Boot# bootm 0x80007fc0 - 0x82ff8000 > > Hum, I actually haven't tested "bootm" in some time, I'll test it right now... > > Here's what i'm seeing with "bootz 0x80200000 > 0x81000000:${initrd_size} 0x815f0000" (intrd is basically ignored as > it's 3.8.x based..) > > http://pastebin.com/LdiemVK3
Nope, not that simple.. http://pastebin.com/Ca47zQLE Let me clone that branch, can you share your execution of make commands... Regards, -- Robert Nelson http://www.rcn-ee.com/ -- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/groups/opt_out.
