On Wed, Nov 6, 2013 at 10:58 AM, Robert Nelson <[email protected]> wrote: > On Wed, Nov 6, 2013 at 10:39 AM, Robert Nelson <[email protected]> > wrote: >> On Wed, Nov 6, 2013 at 9:29 AM, Jason Kridner <[email protected]> >> wrote: >>> Robert, >>> >>> I'm starting with the kernel at >>> http://github.com/beagleboard/kernel/tree/3.12. I've pushed a patched >>> version of the tree to http://github.com/beagleboard/linux/tree/3.12. >>> >>> To build the kernel, I'm using buildroot via >>> http://github.com/jadonk/buildroot/tree/latest. >>> >>> make beaglebone_config >>> make >>> >>> I'm booting the MLO and u-boot.img that are in the buildroot >>> output/images. I then try the following: >>> >>> U-Boot SPL 2013.07 (Oct 30 2013 - 09:44:19) >>> musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, >>> SoftConn) >>> musb-hdrc: MHDRC RTL version 2.0 >>> musb-hdrc: setup fifo_mode 4 >>> musb-hdrc: 28/31 max ep, 16384/16384 memory >>> USB Peripheral mode controller at 47401000 using PIO, IRQ 0 >>> musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, >>> SoftConn) >>> musb-hdrc: MHDRC RTL version 2.0 >>> musb-hdrc: setup fifo_mode 4 >>> musb-hdrc: 28/31 max ep, 16384/16384 memory >>> USB Host mode controller at 47401800 using PIO, IRQ 0 >>> OMAP SD/MMC: 0 >>> reading args >>> spl: error reading image args, err - -1 >>> reading u-boot.img >>> reading u-boot.img >>> >>> >>> U-Boot 2013.07 (Oct 30 2013 - 09:44:19) >>> >>> I2C: ready >>> DRAM: 512 MiB >>> WARNING: Caches not enabled >>> NAND: 0 MiB >>> MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 >>> *** Warning - readenv() failed, using default environment >>> >>> musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, >>> SoftConn) >>> musb-hdrc: MHDRC RTL version 2.0 >>> musb-hdrc: setup fifo_mode 4 >>> musb-hdrc: 28/31 max ep, 16384/16384 memory >>> USB Peripheral mode controller at 47401000 using PIO, IRQ 0 >>> musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, >>> SoftConn) >>> musb-hdrc: MHDRC RTL version 2.0 >>> musb-hdrc: setup fifo_mode 4 >>> musb-hdrc: 28/31 max ep, 16384/16384 memory >>> USB Host mode controller at 47401800 using PIO, IRQ 0 >>> Net: <ethaddr> not set. Validating first E-fuse MAC >>> cpsw, usb_ether >>> Hit any key to stop autoboot: 0 >>> U-Boot# >>> U-Boot# run findfdt >>> U-Boot# setenv bootargs console=${console} >>> U-Boot# load mmc 0 0x80007fc0 uImage >>> reading uImage >>> 34759872 bytes read in 3941 ms (8.4 MiB/s) >>> U-Boot# load mmc 0 0x82ff8000 ${fdtfile} >>> reading am335x-boneblack.dtb >>> 18465 bytes read in 9 ms (2 MiB/s) >>> U-Boot# bootm 0x80007fc0 - 0x82ff8000 >> >> Hum, I actually haven't tested "bootm" in some time, I'll test it right >> now... >> >> Here's what i'm seeing with "bootz 0x80200000 >> 0x81000000:${initrd_size} 0x815f0000" (intrd is basically ignored as >> it's 3.8.x based..) >> >> http://pastebin.com/LdiemVK3 > > Nope, not that simple.. > http://pastebin.com/Ca47zQLE > > Let me clone that branch, can you share your execution of make commands...
Ah i see now, buildroot.. this may take a bit, 100k bandwidth here.. ;) Regards, -- Robert Nelson http://www.rcn-ee.com/ -- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/groups/opt_out.
