Anyone else having trouble loading cape dtbo files at boot? I cannot get cape manager to manually load/override/overlay either: sudo echo ANY-CAPE > /sys/devices/bone-cape.9/slots "Permission denied"
I've tried an A1 audio cape and a couple of capes that I built. I've tried recompiling the dts sources. The dmesg logs (just one example) say "failed to load firmware 'BB-BONE-AUDI-01-00A1.dtbo'", which I know exists in /lib/firmware and has the same permissions as the other dtbo files. Louis On Thursday, January 16, 2014 2:01:17 PM UTC-6, RobertCNelson wrote: > > On Thu, Jan 16, 2014 at 1:41 PM, <[email protected] <javascript:>> > wrote: > > On Thursday, January 16, 2014 12:10:35 PM UTC-5, [email protected] > > wrote: > >> > >> > >> Fantastic, thanks for this, I'm in the process of running my first > build. > >> > > > > Success! ... I think. Don't seem to have working ethernet, here's the > > console output: > > > > [ 0.361322] omap2_mbox_probe: platform not supported > > [ 0.528826] tps65217-bl tps65217-bl: no platform data provided > > [ 0.593518] bone-capemgr bone_capemgr.9: slot #0: No cape found > > [ 0.630626] bone-capemgr bone_capemgr.9: slot #1: No cape found > > [ 0.667733] bone-capemgr bone_capemgr.9: slot #2: No cape found > > [ 0.704842] bone-capemgr bone_capemgr.9: slot #3: No cape found > > [ 0.720846] bone-capemgr bone_capemgr.9: slot #6: BB-BONELT-HDMIN > > conflict P8.45 (#5:BB-BONELT-HDMI) > > [ 0.730428] bone-capemgr bone_capemgr.9: slot #6: Failed verification > > [ 0.737160] bone-capemgr bone_capemgr.9: loader: failed to load > slot-6 > > BB-BONELT-HDMIN:00A0 (prio 2) > > [ 0.753514] omap_hsmmc mmc.5: of_parse_phandle_with_args of 'reset' > > failed > > [ 0.816446] pinctrl-single 44e10800.pinmux: pin 44e10854 already > > requested by 44e10800.pinmux; cannot claim for gpio-leds.8 > > [ 0.828157] pinctrl-single 44e10800.pinmux: pin-21 (gpio-leds.8) > status > > -22 > > [ 0.835441] pinctrl-single 44e10800.pinmux: could not request pin 21 > on > > device pinctrl-single > > Loading, please wait... > > Scanning for Btrfs filesystems > > systemd-fsck[201]: rootfs: clean, 32162/111104 files, 140904/444160 > blocks > > [ 6.087883] libphy: PHY 4a101000.mdio:01 not found > > [ 6.092953] net eth0: phy 4a101000.mdio:01 not found on slave 1 > > Give it a few more seconds, currently "wicd" is under control of eth0 > (not /etc/network/interfaces) on 3.8 it takes wicd about 2-3 calls > before it gets it.. > > The only reason i'm using wicd over /etc/network/interfaces is to > remove the 2 minute timeout if eth0 isn't connected... > > Regards, > > -- > Robert Nelson > http://www.rcn-ee.com/ > -- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/groups/opt_out.
