Hi, Schematic wise both are same.
On Wed, Sep 17, 2014 at 2:51 AM, Jesse Cobra <[email protected]> wrote: > OK, and what is different between your board and CircuitCo schematic wise? > On Sep 16, 2014 8:53 AM, "Prakash Parmar" <[email protected]> > wrote: > >> Hi, >> >> Here CircuitCo cape is not available So we decided to make our own. >> >> >> On Tue, Sep 16, 2014 at 7:20 PM, Jesse Cobra <[email protected]> >> wrote: >> >>> What happens when you try the CircuitCO audio cape? >>> Does it work fine? >>> >>> On Mon, Sep 15, 2014 at 10:14 PM, Prakash Parmar < >>> [email protected]> wrote: >>> >>>> Hi, >>>> >>>> How I can check this two things ? >>>> >>>> 2) check if SYS_RESET is actually deasserted and high >>>> 3) check if DIN/DOUT are correctly connected and not flipped, because >>>> DIN data must go into CODEC, while DOUT must go out and vise versa >>>> >>>> I'm not clear about this. Actually I have two Boards one with 10K >>>> resistors and one with 4.6K . >>>> >>>> Thanks & Regards, >>>> Prakash P. >>>> >>>> On Tue, Sep 16, 2014 at 12:34 AM, Maxim Podbereznyy <[email protected] >>>> > wrote: >>>> >>>>> what is exactly not clear for you? >>>>> >>>>> how to change resistors or how to copy/paste commands in a shell? >>>>> >>>>> 2014-09-15 21:46 GMT+04:00 <[email protected]>: >>>>> >>>>>> HI, >>>>>> Thanks For reply. >>>>>> >>>>>> Can you please tell me how I can Do that ? >>>>>> >>>>>> >>>>>> Thanks & Regards, >>>>>> Prakash P. >>>>>> >>>>>> On Monday, September 15, 2014 8:01:19 PM UTC+5:30, liyaoshi wrote: >>>>>>> >>>>>>> Have you config the i2c pin pulled up ? >>>>>>> and >>>>>>> whats the speed of your i2c bus ? >>>>>>> >>>>>>> 2014-09-15 2:09 GMT+08:00 <[email protected]>: >>>>>>> >>>>>>>> Hi, >>>>>>>> >>>>>>>> I have made custom Audio cape using TLV320AIC3107. Here is a >>>>>>>> circuit diagram : >>>>>>>> >>>>>>>> >>>>>>>> <http://e2e.ti.com/cfs-file.ashx/__key/telligent-evolution-components-attachments/00-64-01-00-01-29-55-62/audio.png> >>>>>>>> >>>>>>>> >>>>>>>> I make it same ( Pin configurations and all ) as what is available >>>>>>>> at CircuitCO using TLC320AIC3104 codec. I follow All steps like Disable >>>>>>>> HDMI and Load Device Tree BB-BONE-AUDI-02-00A0.dts and I it works >>>>>>>> fine. >>>>>>>> >>>>>>>> But my problem is when I run speaker-test system hangs (freezes) >>>>>>>> and I have to Hard Reset BeagleBone. >>>>>>>> >>>>>>>> Here is what i did and what I get in dmesg. >>>>>>>> >>>>>>>> >>>>>>>> *root@beaglebone:~# speaker-test * >>>>>>>> >>>>>>>> speaker-test 1.0.25 >>>>>>>> >>>>>>>> Playback device is default >>>>>>>> Stream parameters are 48000Hz, S16_LE, 1 channels >>>>>>>> Using 16 octaves of pink noise >>>>>>>> Rate set to 48000Hz (requested 48000Hz) >>>>>>>> Buffer size range from 128 to 32768 >>>>>>>> Period size range from 8 to 2048 >>>>>>>> Using max buffer size 32768 >>>>>>>> Periods = 4 >>>>>>>> >>>>>>>> >>>>>>>> *And in Dmesg : * >>>>>>>> >>>>>>>> [ 205.540653] omap_i2c 4819c000.i2c: Arbitration lost >>>>>>>> [ 206.572921] omap_i2c 4819c000.i2c: controller timed out >>>>>>>> [ 206.580024] omap_i2c 4819c000.i2c: Arbitration lost >>>>>>>> [ 207.611983] omap_i2c 4819c000.i2c: controller timed out >>>>>>>> [ 207.618668] omap_i2c 4819c000.i2c: Arbitration lost >>>>>>>> [ 212.626062] omap_i2c 4819c000.i2c: Arbitration lost >>>>>>>> [ 213.658853] omap_i2c 4819c000.i2c: controller timed out >>>>>>>> [ 213.666881] omap_i2c 4819c000.i2c: Arbitration lost >>>>>>>> [ 214.699867] omap_i2c 4819c000.i2c: controller timed out >>>>>>>> [ 214.707912] omap_i2c 4819c000.i2c: Arbitration lost >>>>>>>> [ 215.740887] omap_i2c 4819c000.i2c: controller timed out >>>>>>>> [ 215.748952] omap_i2c 4819c000.i2c: Arbitration lost >>>>>>>> >>>>>>>> >>>>>>>> I also cross check device tree file and I found that it also works >>>>>>>> for TLV320AIC3107 codec So I think it is not issue. >>>>>>>> >>>>>>>> An one have Idea what is wrong Please Help ME !!!! >>>>>>>> >>>>>>>> >>>>>>>> Thanks & Regards >>>>>>>> >>>>>>>> Prakash P. >>>>>>>> >>>>>>>> -- >>>>>>>> For more options, visit http://beagleboard.org/discuss >>>>>>>> --- >>>>>>>> You received this message because you are subscribed to the Google >>>>>>>> Groups "BeagleBoard" group. >>>>>>>> To unsubscribe from this group and stop receiving emails from it, >>>>>>>> send an email to [email protected]. >>>>>>>> For more options, visit https://groups.google.com/d/optout. >>>>>>>> >>>>>>> >>>>>>> -- >>>>>> For more options, visit http://beagleboard.org/discuss >>>>>> --- >>>>>> You received this message because you are subscribed to the Google >>>>>> Groups "BeagleBoard" group. >>>>>> To unsubscribe from this group and stop receiving emails from it, >>>>>> send an email to [email protected]. >>>>>> For more options, visit https://groups.google.com/d/optout. >>>>>> >>>>> >>>>> >>>>> >>>>> -- >>>>> LinkedIn - http://www.linkedin.com/in/maximpodbereznyy >>>>> Company - http://www.linkedin.com/company/mentorel >>>>> Facebook - https://www.facebook.com/mentorel.company >>>>> >>>>> -- >>>>> For more options, visit http://beagleboard.org/discuss >>>>> --- >>>>> You received this message because you are subscribed to a topic in the >>>>> Google Groups "BeagleBoard" group. >>>>> To unsubscribe from this topic, visit >>>>> https://groups.google.com/d/topic/beagleboard/0ickf2E6NNs/unsubscribe. >>>>> To unsubscribe from this group and all its topics, send an email to >>>>> [email protected]. >>>>> For more options, visit https://groups.google.com/d/optout. >>>>> >>>> >>>> -- >>>> For more options, visit http://beagleboard.org/discuss >>>> --- >>>> You received this message because you are subscribed to the Google >>>> Groups "BeagleBoard" group. >>>> To unsubscribe from this group and stop receiving emails from it, send >>>> an email to [email protected]. >>>> For more options, visit https://groups.google.com/d/optout. >>>> >>> >>> -- >>> For more options, visit http://beagleboard.org/discuss >>> --- >>> You received this message because you are subscribed to a topic in the >>> Google Groups "BeagleBoard" group. >>> To unsubscribe from this topic, visit >>> https://groups.google.com/d/topic/beagleboard/0ickf2E6NNs/unsubscribe. >>> To unsubscribe from this group and all its topics, send an email to >>> [email protected]. >>> For more options, visit https://groups.google.com/d/optout. >>> >> >> -- >> For more options, visit http://beagleboard.org/discuss >> --- >> You received this message because you are subscribed to the Google Groups >> "BeagleBoard" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to [email protected]. >> For more options, visit https://groups.google.com/d/optout. >> > -- > For more options, visit http://beagleboard.org/discuss > --- > You received this message because you are subscribed to a topic in the > Google Groups "BeagleBoard" group. > To unsubscribe from this topic, visit > https://groups.google.com/d/topic/beagleboard/0ickf2E6NNs/unsubscribe. > To unsubscribe from this group and all its topics, send an email to > [email protected]. > For more options, visit https://groups.google.com/d/optout. > -- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/d/optout.
