Very cool, thanks. On 20 November 2014 10:47, Maxim Podbereznyy <[email protected]> wrote:
> Michael, > > here is a module based on BBB schematics except for HDMI and eMMC. It was > tested in a Temperature Chamber to comply with industrial requirements: > http://www.mentorel.com/product/usomiq-am335x/ > fully -40 +85 C compatible! > > 2014-11-20 18:34 GMT+03:00 Michael Wood <[email protected]>: > >> Gerald, do you have any more info on that? Occasionally I'll see someone >> who's trying to do it, but rarely someone who *has.* >> >> FYI for the community, CircuitCo sales offered me a BBB clone with all >> components rated to -40 C except the LEDs which are rated to -20 C, for $89 >> in low qty. Actually getting one may be the challenge. >> >> Thanks again. >> >> On 20 November 2014 10:33, Michael Wood <[email protected]> wrote: >> >>> David, I fully understand. I previously went through the markings on the >>> parts I can read with 10x magnification, but a few elude me (hence my >>> original question). Y4 markings read: >>> >>> 0245760 (freq) >>> DCP1423 (?) >>> 2643 (date/batch code?) >>> >>> The ASDMB datasheet suggests an "ASDMB," and the ILSI datasheet clearly >>> shows an "ILSI" on the part. So the only part left is the >>> ECS-2033-24.576-B? Seems odd. >>> >>> Thanks guys. I'm not worried, this shouldn't be hard to figure out. >>> >>> M >>> >>> On 19 November 2014 20:19, Gerald Coley <[email protected]> wrote: >>> >>>> Good luck! >>>> >>>> BTW, someone has already done this and have a BOM already done. They >>>> have actually built and shipped an industrial version of the board. >>>> >>>> Gerald >>>> >>>> >>>> On Wed, Nov 19, 2014 at 5:38 PM, Michael Wood <[email protected]> >>>> wrote: >>>> >>>>> On 19 November 2014 15:41, Gerald Coley <[email protected]> >>>>> wrote: >>>>> >>>>>> If you are asking which ones are mounted on the board, any of those >>>>>> can be mounted at any time on any build based on availability >>>>> >>>>> >>>>> Bingo. This is just what I needed. >>>>> >>>>> FYI, and as we all know, some parts are pretty tough to read anything >>>>> off of, and even if you get something it might only be a batch/date code. >>>>> >>>>> Robert this is just for development of course, trying to figure how to >>>>> leverage the fantastic open source design while modifying it to our specs >>>>> (low temp, obvi) before spinning off our own board. I wouldn't ask a >>>>> consumer/hobbyist dev board to be industrial grade by any definition. >>>>> >>>>> Thanks both! >>>>> >>>>> -- >>>>> For more options, visit http://beagleboard.org/discuss >>>>> --- >>>>> You received this message because you are subscribed to the Google >>>>> Groups "BeagleBoard" group. >>>>> To unsubscribe from this group and stop receiving emails from it, send >>>>> an email to [email protected]. >>>>> For more options, visit https://groups.google.com/d/optout. >>>>> >>>> >>>> >>>> >>>> -- >>>> Gerald >>>> >>>> [email protected] >>>> http://beagleboard.org/ >>>> http://circuitco.com/support/ >>>> >>>> -- >>>> For more options, visit http://beagleboard.org/discuss >>>> --- >>>> You received this message because you are subscribed to a topic in the >>>> Google Groups "BeagleBoard" group. >>>> To unsubscribe from this topic, visit >>>> https://groups.google.com/d/topic/beagleboard/p_DK-HE1Ds4/unsubscribe. >>>> To unsubscribe from this group and all its topics, send an email to >>>> [email protected]. >>>> For more options, visit https://groups.google.com/d/optout. >>>> >>> >>> >> -- >> For more options, visit http://beagleboard.org/discuss >> --- >> You received this message because you are subscribed to the Google Groups >> "BeagleBoard" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to [email protected]. >> For more options, visit https://groups.google.com/d/optout. >> > > > > -- > LinkedIn - http://www.linkedin.com/in/maximpodbereznyy > Company - http://www.linkedin.com/company/mentorel > Facebook - https://www.facebook.com/mentorel.company > > -- > For more options, visit http://beagleboard.org/discuss > --- > You received this message because you are subscribed to a topic in the > Google Groups "BeagleBoard" group. > To unsubscribe from this topic, visit > https://groups.google.com/d/topic/beagleboard/p_DK-HE1Ds4/unsubscribe. > To unsubscribe from this group and all its topics, send an email to > [email protected]. > For more options, visit https://groups.google.com/d/optout. > -- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/d/optout.
