For sure. :) I have both 3.3v and 5v logic ones. On Sat, Jan 10, 2015 at 2:04 PM, evilwulfie <[email protected]> wrote:
> remember 3.3v ftdi ONLY > > > On 1/10/2015 12:39 PM, Kevin Groce wrote: > > Rev Sticker says A6A and is stuck on the header. I will boot and check > what distro/ver is installed and see if my FTDI adapter will work on the > console port. Just have not had a moment rest from work. > > > KG > > On Sat, Jan 10, 2015 at 12:20 PM, William Hermans <[email protected]> > wrote: > >> First of all, you never mentioned what you have installed on the eMMC >> currently. Secondly, you never mentioned which flasher image you're trying >> to install, and from where. Also, do you have a serial debug cable ? Serial >> debug output should be turned on if it is in fact one of Robert's images. >> Which instructions did you try to follow ? What method did you attempt to >> put the image on the sdcard ? >> >> You left out a lot of important information . . . knowing the actual >> revision number of your beaglebone black would be handy too. It should be >> written on a white sticker stuck on the ethernet jack some where. For >> instance, on ours it is stuck on the side. Just says "A5A" >> >> On Sat, Jan 10, 2015 at 7:59 AM, Kevin Groce <[email protected]> wrote: >> >>> So with that being said what would be the best way to flash this to use >>> more recent bootloaders? >>> >>> Kevin Groce >>> >>> On Fri, Jan 9, 2015 at 10:25 PM, William Hermans <[email protected]> >>> wrote: >>> >>>> Ah, I suppose it could also be an available space issue, but the >>>> reason why I mentioned the above first, was that we have two A5A's here, >>>> and with recent Debian images, I've had to hold the button down until the >>>> board starts to boot. Where in the past, this was never a problem. Of >>>> course, I'm booting from sdcard too, but I have Angstrom with 3.8.8 kernel >>>> on the board ( upgraded once ). SO that should tell you how old the image + >>>> bootloader is on our boards . . . >>>> >>>> On Fri, Jan 9, 2015 at 9:15 PM, William Hermans <[email protected]> >>>> wrote: >>>> >>>>> Problem with the A6A i believe will be old bootloader versus new >>>>> bootloader. e.g. Angstrom + old bootloader on the eMMC, newer bootloader + >>>>> Debian on the sdcard flasher image. >>>>> >>>>> With that said, you should wait for Robert to chime in before taking >>>>> drastic steps. Such as believing your board is bad. It is not impossible, >>>>> but I think it is very unlikely. >>>>> >>>>> On Fri, Jan 9, 2015 at 8:19 PM, evilwulfie <[email protected]> >>>>> wrote: >>>>> >>>>>> With a proper image it should flash. >>>>>> >>>>>> http://elinux.org/Beagleboard:Debian_On_BeagleBone_Black >>>>>> >>>>>> >>>>>> http://elinux.org/Beagleboard:Ubuntu_On_BeagleBone_Black >>>>>> >>>>>> >>>>>> On 1/9/2015 7:37 PM, Kevin Groce wrote: >>>>>> >>>>>> I am having such a hard time with flashing the BBB. I am guessing it >>>>>> is an A6A revision based on the wiki. I am not a novice when it comes to >>>>>> flashing but for some reason this bugger wont flash. I have followed the >>>>>> instructions to a T and results are not forth coming. Do you think I >>>>>> could >>>>>> have a bad board? When I I load the image to the card and press the user >>>>>> boot button I do not get the LED response that is said to happen after >>>>>> flash. I have used cheap 8gb SD card and a sandisk 16gb SD card and both >>>>>> same outcome. Nothing. I need a board that works for a P-port cape >>>>>> project. >>>>>> >>>>>> >>>>>> KG >>>>>> -- >>>>>> For more options, visit http://beagleboard.org/discuss >>>>>> --- >>>>>> You received this message because you are subscribed to the Google >>>>>> Groups "BeagleBoard" group. >>>>>> To unsubscribe from this group and stop receiving emails from it, >>>>>> send an email to [email protected]. >>>>>> For more options, visit https://groups.google.com/d/optout. >>>>>> >>>>>> >>>>>> -- >>>>>> For more options, visit http://beagleboard.org/discuss >>>>>> --- >>>>>> You received this message because you are subscribed to the Google >>>>>> Groups "BeagleBoard" group. >>>>>> To unsubscribe from this group and stop receiving emails from it, >>>>>> send an email to [email protected]. >>>>>> For more options, visit https://groups.google.com/d/optout. >>>>>> >>>>> >>>>> >>>> -- >>>> For more options, visit http://beagleboard.org/discuss >>>> --- >>>> You received this message because you are subscribed to a topic in >>>> the Google Groups "BeagleBoard" group. >>>> To unsubscribe from this topic, visit >>>> https://groups.google.com/d/topic/beagleboard/__xWXqUSDvk/unsubscribe. >>>> To unsubscribe from this group and all its topics, send an email to >>>> [email protected]. >>>> For more options, visit https://groups.google.com/d/optout. >>>> >>> >>> -- >>> For more options, visit http://beagleboard.org/discuss >>> --- >>> You received this message because you are subscribed to the Google >>> Groups "BeagleBoard" group. >>> To unsubscribe from this group and stop receiving emails from it, send >>> an email to [email protected]. >>> For more options, visit https://groups.google.com/d/optout. >>> >> >> -- >> For more options, visit http://beagleboard.org/discuss >> --- >> You received this message because you are subscribed to a topic in the >> Google Groups "BeagleBoard" group. >> To unsubscribe from this topic, visit >> https://groups.google.com/d/topic/beagleboard/__xWXqUSDvk/unsubscribe. >> To unsubscribe from this group and all its topics, send an email to >> [email protected]. >> For more options, visit https://groups.google.com/d/optout. >> > > -- > For more options, visit http://beagleboard.org/discuss > --- > You received this message because you are subscribed to the Google Groups > "BeagleBoard" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > For more options, visit https://groups.google.com/d/optout. > > > -- > For more options, visit http://beagleboard.org/discuss > --- > You received this message because you are subscribed to a topic in the > Google Groups "BeagleBoard" group. > To unsubscribe from this topic, visit > https://groups.google.com/d/topic/beagleboard/__xWXqUSDvk/unsubscribe. > To unsubscribe from this group and all its topics, send an email to > [email protected]. > For more options, visit https://groups.google.com/d/optout. > -- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/d/optout.
