debian@beaglebone:~/bb.org-overlays$ sudo ./install.sh ... ./install.sh: line 36: make: command not found
*sigh* Is there a dependency list anywhere ? On Fri, May 8, 2015 at 2:20 PM, William Hermans <[email protected]> wrote: > Thanks Robert. I went ahead and . . . > > william@eee-pc:~/downloads/linux-images$ *sudo dd > if=/home/william/downloads/linux-images/bone-debian-7.8-console-armhf-2015-03-01-2gb.img > of=/dev/sdb1* > > I figure I'll do a write up, and maybe put up a blogpost to help make > things easier for others who may wish to travel down the same path. If not > . . .well then I'll have an online template at least I can follow. > > > At one point I was pretty good with all the device tree stuff. Now . . . > all the "rust" is starting to show. > > On Fri, May 8, 2015 at 2:15 PM, Robert Nelson <[email protected]> > wrote: > >> On Fri, May 8, 2015 at 3:46 PM, William Hermans <[email protected]> >> wrote: >> > OK *other* work done for the time being, I have some time to tinker my >> > progress so far . . . >> > >> > IM working with a custom barefs rootfs so . . . from what I can glean >> so far >> > i need ... >> > >> > debian@beaglebone:~$ sudo apt-get install bb-customizations >> > ... >> > Setting up bb-customizations (1.20150507-1~bpo70+20150507+1) ... >> > >> > >> > debian@beaglebone:~$ git clone >> > https://github.com/RobertCNelson/bb.org-overlays >> > Cloning into 'bb.org-overlays'... >> > remote: Counting objects: 141, done. >> > remote: Compressing objects: 100% (114/114), done. >> > remote: Total 141 (delta 66), reused 90 (delta 15), pack-reused 0 >> > Receiving objects: 100% (141/141), 34.84 KiB, done. >> > Resolving deltas: 100% (66/66), done. >> > >> > debian@beaglebone:~$ cd ./bb.org-overlays/ >> > debian@beaglebone:~/bb.org-overlays$ sudo ./make.sh >> > sudo: ./make.sh: command not found >> >> Sorry, i cleaned up the makefile this morning: >> >> "./install.sh" will do everything >> >> > >> > At this point I did a bit of investigation. First I already figured dtc >> was >> > not installed. Second . . . /opt/scripts/ is fairly bare. Only two >> scripts >> > under the tools sub directory. Related to eMMC, and partition growing. >> >> "./dtc-overlay.sh" is now in "bb.org-overlays" too... >> >> > I realize from where I am it is probably possible to fix all of this. >> > However it is probably not worth the hassle - As my "testing" sdcard >> image >> > is very tainted by now, and I have "notes" to get me back to a working >> > pristine image. So, last night I downloaded two testing images. Both >> > console, but one is Jessie, and the other is Wheezy as far as I can >> tell. I >> > mounted one images and noticed that the /opt/scripts/ directory seems >> to be >> > fully populated. Other than that I did not further investigation. >> > >> > Is there a preferred image to start off with as a base ? >> >> any is fine, all the tools are in the git repo now.. >> >> > >> > I also noticed in the sources for the git you posted a link to there is >> a >> > dtbo file for CAN1. Thanks for that Robert. I figured I was going to >> have to >> > hunt down and compile from my *bone47 dev base . . . which may have >> turned >> > into a nightmare for me . . . >> >> Regards, >> >> -- >> Robert Nelson >> https://rcn-ee.com/ >> >> -- >> For more options, visit http://beagleboard.org/discuss >> --- >> You received this message because you are subscribed to the Google Groups >> "BeagleBoard" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to [email protected]. >> For more options, visit https://groups.google.com/d/optout. >> > > -- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/d/optout.
