On Fri, Jun 5, 2015 at 8:48 AM, Micka <[email protected]> wrote: > The config file is ok > > But I don't have IP? > > eth0 Link encap:Ethernet HWaddr de:ad:be:ef:ca:fe > inet6 addr: fe80::dcad:beff:feef:cafe/64 Scope:Link > UP BROADCAST RUNNING MULTICAST DYNAMIC MTU:1500 Metric:1 > RX packets:364 errors:0 dropped:0 overruns:0 frame:0 > TX packets:24 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:1000 > RX bytes:24543 (23.9 KiB) TX bytes:4365 (4.2 KiB) > Interrupt:174 > > > root@arm:~# dmesg | grep "phy 4a" > [ 6.291037] net eth0: phy 4a101000.mdio:01 not found on slave 1 > [ 7.736772] net eth0: phy 4a101000.mdio:01 not found on slave 1 > > > the led orange is ok and led green is blinking which is ok > > I tried : > > root@arm:~# /etc/init.d/networking restart > [ 185.246094] libphy: PHY 4a101000.mdio:01 not found > [ 185.251107] net eth0: phy 4a101000.mdio:01 not found on slave 1 > [ 185.265139] net eth0: BQL enabled > [ 185.275592] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready > [ 185.275616] 8021q: adding VLAN 0 to HW filter on device eth0 > [ 187.243856] cpsw 4a100000.ethernet eth0: Link is Up - 100Mbps/Full - flow > control rx/tx > [ 187.243961] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready > > > It works : > > root@arm:~# ifconfig > eth0 Link encap:Ethernet HWaddr de:ad:be:ef:ca:fe > inet addr:190.190.167.10 Bcast:190.190.255.255 Mask:255.255.0.0 > inet6 addr: fe80::dcad:beff:feef:cafe/64 Scope:Link > UP BROADCAST RUNNING MULTICAST DYNAMIC MTU:1500 Metric:1 > RX packets:6329 errors:0 dropped:0 overruns:0 frame:0 > TX packets:122 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:1000 > RX bytes:1481867 (1.4 MiB) TX bytes:26160 (25.5 KiB) > Interrupt:174 > > > The entire log of net : > > [ 0.090282] Initializing cgroup subsys net_cls > [ 0.090305] Initializing cgroup subsys net_prio > [ 2.794392] audit: initializing netlink subsys (disabled) > [ 2.985118] cpsw 4a100000.ethernet: Detected MACID = 34:b1:f7:1b:02:c2 > [ 6.282323] net eth0: initializing cpsw version 1.12 (0) > [ 6.285883] net eth0: phy found : id is : 0x7c0f1 > [ 6.291037] net eth0: phy 4a101000.mdio:01 not found on slave 1 > [ 6.302341] net eth0: BQL enabled > [ 7.363496] using random self ethernet address > [ 7.363520] using random host ethernet address > [ 7.363532] using host ethernet address: 34:B1:F7:1B:02:C3 > [ 7.364433] using random self ethernet address > [ 7.364443] using random host ethernet address > [ 7.364519] g_ether gadget: Ethernet Gadget, version: Memorial Day 2008 > [ 7.729161] net eth0: initializing cpsw version 1.12 (0) > [ 7.731536] net eth0: phy found : id is : 0x7c0f1 > [ 7.736772] net eth0: phy 4a101000.mdio:01 not found on slave 1 > [ 7.816588] net eth0: BQL enabled > [ 8.410985] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 > [ 10.803877] cpsw 4a100000.ethernet eth0: Link is Up - 100Mbps/Full - flow > control rx/tx > [ 136.883463] cpsw 4a100000.ethernet eth0: Link is Down > [ 137.883895] cpsw 4a100000.ethernet eth0: Link is Up - 100Mbps/Full - flow > control rx/tx > [ 185.243543] net eth0: initializing cpsw version 1.12 (0) > [ 185.246016] net eth0: phy found : id is : 0x7c0f1 > [ 185.251107] net eth0: phy 4a101000.mdio:01 not found on slave 1 > [ 185.265139] net eth0: BQL enabled
> [ 187.243856] cpsw 4a100000.ethernet eth0: Link is Up - 100Mbps/Full - flow > control rx/tx Ah... It's clearly working.. read: https://wiki.debian.org/NetworkConfiguration Regards, -- Robert Nelson https://rcn-ee.com/ -- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/d/optout.
