I know how to configure IP address:
auto eth0
allow-hotplug eth0
iface eth0 inet static
address 190.190.167.10
netmask 255.255.0.0
gateway 190.190.255.253
But that didn't work, any idea ? suggestion on where I am wrong ?
Thx,
Le ven. 5 juin 2015 à 15:51, Robert Nelson <[email protected]> a
écrit :
> On Fri, Jun 5, 2015 at 8:48 AM, Micka <[email protected]> wrote:
> > The config file is ok
> >
> > But I don't have IP?
> >
> > eth0 Link encap:Ethernet HWaddr de:ad:be:ef:ca:fe
> > inet6 addr: fe80::dcad:beff:feef:cafe/64 Scope:Link
> > UP BROADCAST RUNNING MULTICAST DYNAMIC MTU:1500 Metric:1
> > RX packets:364 errors:0 dropped:0 overruns:0 frame:0
> > TX packets:24 errors:0 dropped:0 overruns:0 carrier:0
> > collisions:0 txqueuelen:1000
> > RX bytes:24543 (23.9 KiB) TX bytes:4365 (4.2 KiB)
> > Interrupt:174
> >
> >
> > root@arm:~# dmesg | grep "phy 4a"
> > [ 6.291037] net eth0: phy 4a101000.mdio:01 not found on slave 1
> > [ 7.736772] net eth0: phy 4a101000.mdio:01 not found on slave 1
> >
> >
> > the led orange is ok and led green is blinking which is ok
> >
> > I tried :
> >
> > root@arm:~# /etc/init.d/networking restart
> > [ 185.246094] libphy: PHY 4a101000.mdio:01 not found
> > [ 185.251107] net eth0: phy 4a101000.mdio:01 not found on slave 1
> > [ 185.265139] net eth0: BQL enabled
> > [ 185.275592] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
> > [ 185.275616] 8021q: adding VLAN 0 to HW filter on device eth0
> > [ 187.243856] cpsw 4a100000.ethernet eth0: Link is Up - 100Mbps/Full -
> flow
> > control rx/tx
> > [ 187.243961] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
> >
> >
> > It works :
> >
> > root@arm:~# ifconfig
> > eth0 Link encap:Ethernet HWaddr de:ad:be:ef:ca:fe
> > inet addr:190.190.167.10 Bcast:190.190.255.255
> Mask:255.255.0.0
> > inet6 addr: fe80::dcad:beff:feef:cafe/64 Scope:Link
> > UP BROADCAST RUNNING MULTICAST DYNAMIC MTU:1500 Metric:1
> > RX packets:6329 errors:0 dropped:0 overruns:0 frame:0
> > TX packets:122 errors:0 dropped:0 overruns:0 carrier:0
> > collisions:0 txqueuelen:1000
> > RX bytes:1481867 (1.4 MiB) TX bytes:26160 (25.5 KiB)
> > Interrupt:174
> >
> >
> > The entire log of net :
> >
> > [ 0.090282] Initializing cgroup subsys net_cls
> > [ 0.090305] Initializing cgroup subsys net_prio
> > [ 2.794392] audit: initializing netlink subsys (disabled)
> > [ 2.985118] cpsw 4a100000.ethernet: Detected MACID = 34:b1:f7:1b:02:c2
> > [ 6.282323] net eth0: initializing cpsw version 1.12 (0)
> > [ 6.285883] net eth0: phy found : id is : 0x7c0f1
> > [ 6.291037] net eth0: phy 4a101000.mdio:01 not found on slave 1
> > [ 6.302341] net eth0: BQL enabled
> > [ 7.363496] using random self ethernet address
> > [ 7.363520] using random host ethernet address
> > [ 7.363532] using host ethernet address: 34:B1:F7:1B:02:C3
> > [ 7.364433] using random self ethernet address
> > [ 7.364443] using random host ethernet address
> > [ 7.364519] g_ether gadget: Ethernet Gadget, version: Memorial Day
> 2008
> > [ 7.729161] net eth0: initializing cpsw version 1.12 (0)
> > [ 7.731536] net eth0: phy found : id is : 0x7c0f1
> > [ 7.736772] net eth0: phy 4a101000.mdio:01 not found on slave 1
> > [ 7.816588] net eth0: BQL enabled
> > [ 8.410985] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
> > [ 10.803877] cpsw 4a100000.ethernet eth0: Link is Up - 100Mbps/Full -
> flow
> > control rx/tx
> > [ 136.883463] cpsw 4a100000.ethernet eth0: Link is Down
> > [ 137.883895] cpsw 4a100000.ethernet eth0: Link is Up - 100Mbps/Full -
> flow
> > control rx/tx
> > [ 185.243543] net eth0: initializing cpsw version 1.12 (0)
> > [ 185.246016] net eth0: phy found : id is : 0x7c0f1
> > [ 185.251107] net eth0: phy 4a101000.mdio:01 not found on slave 1
> > [ 185.265139] net eth0: BQL enabled
>
>
> > [ 187.243856] cpsw 4a100000.ethernet eth0: Link is Up - 100Mbps/Full -
> flow
> > control rx/tx
>
> Ah... It's clearly working..
>
> read: https://wiki.debian.org/NetworkConfiguration
>
> Regards,
>
>
> --
> Robert Nelson
> https://rcn-ee.com/
>
> --
> For more options, visit http://beagleboard.org/discuss
> ---
> You received this message because you are subscribed to the Google Groups
> "BeagleBoard" group.
> To unsubscribe from this group and stop receiving emails from it, send an
> email to [email protected].
> For more options, visit https://groups.google.com/d/optout.
>
--
For more options, visit http://beagleboard.org/discuss
---
You received this message because you are subscribed to the Google Groups
"BeagleBoard" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to [email protected].
For more options, visit https://groups.google.com/d/optout.
