Hello! I have 5 BBB RevC from element14. Now I get 10 BBB from Circuitco, also Rev C.
The shock: When I flash my own Image, where I made for the BBB and running on element14 Rev C, on the new BBB ... the flash starts ... ends ... and the BBB are not booting. Only the Power LED are on, all USR LED are off and never getting on. Both Images has with: cat /etc/dogtag BeagleBoard.org Debian Image 2015-03-01 So, the Image is the same! Has someone an idea, why it not booting? When insert MY image uSD and I debug with holding Button S2: U-Boot 2013.04 (Sep 25 2013 - 00:49:30)<\r><\n> <\r><\n> I2C: ready<\r><\n> DRAM: 512 MiB<\r><\n> WARNING: Caches not enabled<\r><\n> NAND: No NAND device found!!!<\r><\n> 0 MiB<\r><\n> MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1<\r><\n> *** Warning - readenv() failed, using default environment<\r><\n> <\r><\n> musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn)<\r><\n> musb-hdrc: MHDRC RTL version 2.0 <\r><\n> musb-hdrc: setup fifo_mode 4<\r><\n> musb-hdrc: 28/31 max ep, 16384/16384 memory<\r><\n> USB Peripheral mode controller at 47401000 using PIO, IRQ 0<\r><\n> musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn)<\r><\n> musb-hdrc: MHDRC RTL version 2.0 <\r><\n> musb-hdrc: setup fifo_mode 4<\r><\n> musb-hdrc: 28/31 max ep, 16384/16384 memory<\r><\n> USB Host mode controller at 47401800 using PIO, IRQ 0<\r><\n> Net: <ethaddr> not set. Validating first E-fuse MAC<\r><\n> cpsw, usb_ether<\r><\n> Hit any key to stop autoboot: 1 <\b><\b><\b> 0 <\r><\n> mmc0 is current device<\r><\n> SD/MMC found on device 0<\r><\n> reading uEnv.txt<\r><\n> 236 bytes read in 4 ms (57.6 KiB/s)<\r><\n> Loaded environment from uEnv.txt<\r><\n> Importing environment from mmc ...<\r><\n> Running uenvcmd ...<\r><\n> reading uImage<\r><\n> 11748096 bytes read in 1343 ms (8.3 MiB/s)<\r><\n> reading /am335x-boneblack.dtb<\r><\n> 24884 bytes read in 9 ms (2.6 MiB/s)<\r><\n> ## Booting kernel from Legacy Image at 80200000 ...<\r><\n> Image Name: Linux-3.8.13<\r><\n> Image Type: ARM Linux Kernel Image (uncompressed)<\r><\n> Data Size: 11748032 Bytes = 11.2 MiB<\r><\n> Load Address: 80008000<\r><\n> Entry Point: 80008000<\r><\n> Verifying Checksum ... OK<\r><\n> ## Flattened Device Tree blob at 81ff0000<\r><\n> Booting using the fdt blob at 0x81ff0000<\r><\n> Loading Kernel Image ... OK<\r><\n> OK<\r><\n> Using Device Tree in place at 81ff0000, end 81ff9133<\r><\n> <\r><\n> Starting kernel ...<\r><\n> <\r><\n> Uncompressing Linux... done, booting the kernel.<\r><\n> [ 1.368876] omap2_mbox_probe: platform not supported<\r><\n> [ 1.379850] tps65217-bl tps65217-bl: no platform data provided<\r><\n> [ 1.455982] bone-capemgr bone_capemgr.9: slot #0: No cape found<\r><\n> [ 1.493088] bone-capemgr bone_capemgr.9: slot #1: No cape found<\r><\n> [ 1.530196] bone-capemgr bone_capemgr.9: slot #2: No cape found<\r><\n> [ 1.567305] bone-capemgr bone_capemgr.9: slot #3: No cape found<\r><\n> [ 1.594091] omap_hsmmc mmc.5: of_parse_phandle_with_args of 'reset' failed<\r><\n> [ 1.659493] pinctrl-single 44e10800.pinmux: pin 44e10854 already requested by 44e10800.pinmux; cannot claim for gpio-leds.8<\r><\n> [ 1.671200] pinctrl-single 44e10800.pinmux: pin-21 (gpio-leds.8) status -22<\r><\n> [ 1.678514] pinctrl-single 44e10800.pinmux: could not request pin 21 on device pinctrl-single HERE the power LED is going off and stop! Thank you for help! -- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/d/optout.
