I have somewhat bricked the BeagleBone Black. When I boot it, when connected using the serial port, it does write the 'C' character continuously. Looking through the board I have seen the a post (https://groups.google.com/forum/#!topic/beagleboard/pDr_rLDYqy4) where it has a similar problem. I have tried reflashing the eMMC using several images but no luck at the moment.
Using the flasher images, this is the output using the serial port: U-Boot 2013.04-dirty (Jun 19 2013 - 09:57:14) I2C: ready DRAM: 512 MiB WARNING: Caches not enabled NAND: No NAND device found!!! 0 MiB MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 *** Warning - readenv() failed, using default environment musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Peripheral mode controller at 47401000 using PIO, IRQ 0 musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Host mode controller at 47401800 using PIO, IRQ 0 Net: <ethaddr> not set. Validating first E-fuse MAC Phy not found PHY reset timed out cpsw, usb_ether Hit any key to stop autoboot: 0 gpio: pin 53 (gpio 53) value is 1 mmc0 is current device micro SD card found mmc0 is current device gpio: pin 54 (gpio 54) value is 1 SD/MMC found on device 0 reading uEnv.txt 14 bytes read in 2 ms (6.8 KiB/s) Loaded environment from uEnv.txt Importing environment from mmc ... gpio: pin 55 (gpio 55) value is 1 4270840 bytes read in 742 ms (5.5 MiB/s) gpio: pin 56 (gpio 56) value is 1 24125 bytes read in 37 ms (636.7 KiB/s) Booting from mmc ... ## Booting kernel from Legacy Image at 80007fc0 ... Image Name: Angstrom/3.8.13/beaglebone Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4270776 Bytes = 4.1 MiB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK ## Flattened Device Tree blob at 80f80000 Booting using the fdt blob at 0x80f80000 XIP Kernel Image ... OK OK Using Device Tree in place at 80f80000, end 80f88e3c Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.194258] omap2_mbox_probe: platform not supported [ 0.204902] tps65217-bl tps65217-bl: no platform data provided [ 0.281411] bone-capemgr bone_capemgr.9: slot #0: No cape found [ 0.318516] bone-capemgr bone_capemgr.9: slot #1: No cape found [ 0.355625] bone-capemgr bone_capemgr.9: slot #2: No cape found [ 0.392734] bone-capemgr bone_capemgr.9: slot #3: No cape found [ 0.412204] bone-capemgr bone_capemgr.9: slot #6: BB-BONELT-HDMIN conflict P8.45 (#5:BB-BONELT-HDMI) [ 0.421850] bone-capemgr bone_capemgr.9: slot #6: Failed verification [ 0.428623] bone-capemgr bone_capemgr.9: loader: failed to load slot-6 BB-BONELT-HDMIN:00A0 (prio 2) [ 0.451158] omap_hsmmc mmc.4: of_parse_phandle_with_args of 'reset' failed [ 0.516302] pinctrl-single 44e10800.pinmux: pin 44e10854 already requested by 44e10800.pinmux; cannot claim for gpio-leds.8 [ 0.528015] pinctrl-single 44e10800.pinmux: pin-21 (gpio-leds.8) status -22 [ 0.535329] pinctrl-single 44e10800.pinmux: could not request pin 21 on device pinctrl-single [ 0.756933] Unhandled fault: external abort on non-linefetch (0x1008) at 0xe09fe000 [ 0.764946] Internal error: : 1008 [#1] SMP THUMB2 [ 0.769950] Modules linked in: [ 0.773154] CPU: 0 Not tainted (3.8.13 #1) [ 0.777817] PC is at cpsw_probe+0x3fc/0x8a2 [ 0.782197] LR is at ioremap_page_range+0xc3/0x100 [ 0.787208] pc : [<c023f752>] lr : [<c019399b>] psr: 80000133 [ 0.787208] sp : df051e18 ip : df04d7f8 fp : 00000001 [ 0.799198] r10: df3dace0 r9 : df3d9590 r8 : 00000000 [ 0.804658] r7 : e09fe000 r6 : df10d600 r5 : df10d610 r4 : df3d9000 [ 0.811477] r3 : 00000000 r2 : 00000800 r1 : c023f73d r0 : e09fe000 [ 0.818299] Flags: Nzcv IRQs on FIQs on Mode SVC_32 ISA Thumb Segment kernel [ 0.826116] Control: 50c5387d Table: 80004019 DAC: 00000015 [ 0.832119] Process swapper/0 (pid: 1, stack limit = 0xdf050240) [ 0.838394] Stack: (0xdf051e18 to 0xdf052000) [ 0.842949] 1e00: 00000000 df2a88c0 [ 0.851500] 1e20: c0659c40 df2a88c0 df3d9298 c036f873 df04cac0 00000000 df051e4c 00000020 [ 0.860052] 1e40: 00000008 c00ce4c1 df051e90 df5fc248 df051e78 df04cac0 df5fc2c8 df5fc248 [ 0.868603] 1e60: df5fc248 c00ce403 00000000 df5fc248 df10c148 df3d00c0 00000000 c00cebdf [ 0.877155] 1e80: df0464b8 c0040449 00000000 00000003 df10c148 00000000 c0672990 df10d610 [ 0.885706] 1ea0: df10d644 c0672990 c01f234d 000000e8 c05edf81 00000000 00000000 c01f2cb9 [ 0.894259] 1ec0: c01f2cad c01f226f 00000000 df10d610 df10d644 c0672990 c01f234d c01f2381 [ 0.902810] 1ee0: 00000000 df051ef0 c0672990 c01f139d df046478 df109880 c0672990 c0672990 [ 0.911361] 1f00: df3d00c0 c06691f8 00000000 c01f1d33 c04ff0a7 df001348 c0672990 c05f62f0 [ 0.919912] 1f20: c061458c c0689cc0 000000e8 c01f2661 00000007 c05f62f0 c061458c c0689cc0 [ 0.928463] 1f40: 000000e8 c000868d c05edf81 13000000 c06145b8 00000008 00000007 c05f62f0 [ 0.937013] 1f60: c061458c c0689cc0 000000e8 c05f62f8 c05d61d5 c05d6691 00000007 00000007 [ 0.945563] 1f80: c05d61d5 00000000 00000000 c0369129 00000000 00000000 00000000 00000000 [ 0.954113] 1fa0: 00000000 c036912f 00000000 c000c6fd 00000000 00000000 00000000 00000000 [ 0.962663] 1fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 0.971212] 1fe0: 00000000 00000000 00000000 00000000 00000013 00000000 7fdf55ff 7df57ddd [ 0.979791] [<c023f752>] (cpsw_probe+0x3fc/0x8a2) from [<c01f2cb9>] (platform_drv_probe+0xd/0xe) [ 0.988986] [<c01f2cb9>] (platform_drv_probe+0xd/0xe) from [<c01f226f>] (driver_probe_device+0x67/0x144) [ 0.998903] [<c01f226f>] (driver_probe_device+0x67/0x144) from [<c01f2381>] (__driver_attach+0x35/0x48) [ 1.008729] [<c01f2381>] (__driver_attach+0x35/0x48) from [<c01f139d>] (bus_for_each_dev+0x29/0x48) [ 1.018191] [<c01f139d>] (bus_for_each_dev+0x29/0x48) from [<c01f1d33>] (bus_add_driver+0x83/0x158) [ 1.027652] [<c01f1d33>] (bus_add_driver+0x83/0x158) from [<c01f2661>] (driver_register+0x4d/0xa4) [ 1.037024] [<c01f2661>] (driver_register+0x4d/0xa4) from [<c000868d>] (do_one_initcall+0x61/0xec) [ 1.046405] [<c000868d>] (do_one_initcall+0x61/0xec) from [<c05d6691>] (kernel_init_freeable+0xb9/0x14c) [ 1.056327] [<c05d6691>] (kernel_init_freeable+0xb9/0x14c) from [<c036912f>] (kernel_init+0x7/0x90) [ 1.065796] [<c036912f>] (kernel_init+0x7/0x90) from [<c000c6fd>] (ret_from_fork+0x11/0x34) [ 1.074529] Code: ff6c e200 f8c4 05c0 (6803) f44f [ 1.079539] ---[ end trace 4f887ca3f0928b01 ]--- [ 1.084817] Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b [ 1.084817] [ 1.094373] drm_kms_helper: panic occurred, switching back to text console Looks like the flasher in the uSD isn't able even to boot. Is there any way to solve this problem ? Thank you, Best regards, -- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/d/optout.
