His overlay is in the first post John. On Fri, Nov 27, 2015 at 5:07 PM, John Syne <[email protected]> wrote:
> One more thing, just defining pinmux in the overlay will have no effect. > The pinmux will only be configured as part of installing the driver. Just > before the kernel calls the driver probe function, it sets up the pinmux as > defined by the pinctrl definition. > > Regards, > John > > > > > On Nov 27, 2015, at 3:58 PM, John Syne <[email protected]> wrote: > > GPIO MODE SETTINGS Bit 6 Bit 5 Bit 4 Bit 3 Bit 2,1,0 Slew Control Receiver > Active Pullup/Pulldown Enable Pullup/down Mux Mode 0 Fast 0 Disable 0 > Pulldown select 0 Enabled 000 Mode 0 to 1 Enable 1 Pullup select 1 > Disabled 111 Mode 7 e.g. OUTPUT GPIO(mode7) 0x07 pulldown, 0x17 pullup, > 0x?f no pullup/down e.g. INPUT GPIO(mode7) 0x27 pulldown, 0x37 pullup, > 0x?f no pullup/down TRM Table 9-60 > > > From the table above, 0x27 in an input and 0x17 is an output. My guess is > that there is some conflict that occurs and that is why the config isn’t > set correctly. What does your overlay look like and what do you see when > you install the overlay? > > Regards, > John > > > > > On Nov 27, 2015, at 1:03 PM, Riley Porter <[email protected]> wrote: > > William, > > Thanks. This basically is exactly what I did reading johns reply. I > guess my main disconnect here is. I can apply a device tree overlay that I > make. I see it "applied" in dmesg and in slots. However the pinmux output > from *cat /sys/kernel/debug/pinctrl/44e10800.pinmux/pins *continues to > show 0x27 for their modes when I specifically set the dtc to 0x17. > > I have not actually tried to use it as an input in code yet. Merely have > been seeing that it is not "applying" what i thought it should. Perhaps I > am looking at the wrong pinoutput? > > for example P9_11's offset is 0x70 and its PIN value is 28. So * | grep > 870* > > root ~/bb.org-overlays # *cat > /sys/kernel/debug/pinctrl/44e10800.pinmux/pins* | grep 870 > pin 28 (44e10870.0) 000000*27* pinctrl-single > > which is not 0x17? > > I am being very wordy here just to make sure you guys know exactly what I > am doing and my expectations. > > > So does anything I am doing look wrong? > > > Again thanks a bunch guys for the help. I have been at this for the > better part of a week now and I agree William it's a step in the WRONG > direction going to Angstrom. > > ril3y > > > > On Fri, Nov 27, 2015 at 3:45 PM, William Hermans <[email protected]> > wrote: > >> *Unfortunately the "answer" was to install angstrom. I was hoping >>> someone on the list would have some secret answer as to why applying an >>> overlay was not changing the pinmux's?* >>> >>> *I would very much like to stick with debian but if the answer is go >>> back angstrom I guess I can live with that.* >>> >>> *Thanks* >> >> You do not have to go back to Angstrom, and if you ask me that is very >> counter productive. Read my guide here: >> http://www.embeddedhobbyist.com/2015/09/beaglebone-black-updating-device-tree-files/ >> >> Do note, that the kernel I talk about at the beginning is just an >> example. You do not have to use the exact kernel I demonstrated. Any 4.x >> kernel should work with that guide. >> >> >> On Fri, Nov 27, 2015 at 1:14 PM, Riley Porter <[email protected]> >> wrote: >> >>> Yes I am running: >>> >>> *Linux beaglebone 4.1.1-bone10 #1 Tue Jul 7 01:15:35 UTC 2015 armv7l >>> GNU/Linux* >>> >>> I followed your instructions but still am at a loss. I was able to >>> update the device tree compiler and the kernel which is now: >>> >>> *Linux beaglebone 4.1.13-ti-r33 #1 SMP PREEMPT Fri Nov 20 11:00:50 UTC >>> 2015 armv7l GNU/Linux* >>> >>> Perhaps describing my exact steps might shed some light on my screw up? >>> >>> >>> *This is the device tree I am testing with:* >>> >>> >>> /* >>>> snip for space >>>> */ >>>> /dts-v1/; >>>> /plugin/; >>>> >>>> /{ >>>> compatible = "ti,beaglebone", "ti,beaglebone-black"; >>>> part-number = "EBB-GPIO-Example"; >>>> version = "00A0"; >>>> >>>> fragment@0 { >>>> target = <&am33xx_pinmux>; >>>> >>>> >>>> __overlay__ { >>>> ebb_example: EBB_GPIO_Example { >>>> pinctrl-single,pins = < >>>> >>>> >>>> /*============= Inputs >>>> ================*/ >>>> 0x070 0x17 // P9_11 PINS$28 GPIO0_30 = >>>> 30 Input Mode7 pullup >>>> 0x078 0x17 // P9_12 PINS$30 GPIO1_28 = >>>> 60 Input Mode7 pullup >>>> 0x074 0x17 // P9_13 PINS$29 GPIO0_31 = >>>> 31 Input Mode7 pullup >>>> 0x048 0x17 // P9_14 PINS$18 GPIO1_18 = >>>> 50 Input Mode7 pullup >>>> 0x040 0x17 // P9_15 PINS$16 GPIO1_16 = >>>> 48 Input Mode7 pullup >>>> 0x04c 0x17 // P9_16 PINS$19 GPIO1_19 = >>>> 51 Input Mode7 pullup >>>> 0x15c 0x17 // P9_17 PINS$87 GPIO0_5 = >>>> 5 Input Mode7 pullup >>>> 0x158 0x17 // P9_18 PINS$86 GPIO0_4 = >>>> 4 Input Mode7 pullup >>>> >>>> /* OUTPUT GPIO(mode7) 0x07 pulldown, >>>> 0x17 pullup, 0x?f no pullup/down */ >>>> /* INPUT GPIO(mode7) 0x27 pulldown, >>>> 0x37 pullup, 0x?f no pullup/down */ >>>> >; >>>> }; >>>> }; >>>> }; >>>> >>>> fragment@1 { >>>> target = <&ocp>; >>>> __overlay__ { >>>> gpio_helper { >>>> compatible = "gpio-of-helper"; >>>> status = "okay"; >>>> pinctrl-names = "default"; >>>> pinctrl-0 = <&ebb_example>; >>>> }; >>>> }; >>>> }; >>>> }; >>> >>> >>> >>> I also removed ALL overlays from my system before doing this below. >>> Here is my output from slots and a python program to get the pins i >>> wrote: >>> >>> *root ~/bbb_stuff # **slots* >>> >>> >>> >>> >>> * 0: PF---- -1 1: PF---- -1 2: PF---- -1 3: PF---- -1 9: P-O-L- >>> 0 Override Board Name,00A0,Override Manuf,EBB-GPIO-Example* >>> >>> *root ~/bbb_stuff # ./getpins * >>> >>> >>> >>> *==================================================Reading Pinux >>> Pins==================================================* >>> >>> >>> >>> >>> >>> >>> >>> >>> *pin 16 (44e10840.0) 00000027 pinctrl-singlepin 18 (44e10848.0) 00000027 >>> pinctrl-singlepin 19 (44e1084c.0) 00000027 pinctrl-singlepin 28 >>> (44e10870.0) 00000017 pinctrl-singlepin 29 (44e10874.0) 00000027 >>> pinctrl-singlepin 30 (44e10878.0) 00000027 pinctrl-singlepin 86 >>> (44e10958.0) 00000027 pinctrl-singlepin 87 (44e1095c.0) 00000027 >>> pinctrl-single* >>> >>> You can clearly see I have requested them all to be 0x17? >>> >>> *Here are the alias's I am using:* >>> >>> *pins='cat /sys/kernel/debug/pinctrl/44e10800.pinmux/pins'**slots='cat >>> /sys/devices/platform/bone_capemgr/slots'* >>> >>> >>> *This is the command i used to compile the dt.* >>> *dtc -O dtb -o EBB-GPIO-Example-00A0.dtbo -b 0 -@ EBB-GPIO-Example.dts* >>> >>> *This is the command I used to install it:* >>> *echo EBB-GPIO-Example-00A0 > >>> "/sys/devices/platform/bone_capemgr/slots"* >>> >>> >>> *This is the dmesg output after installing the overlay:* >>> >>> >>> >>> >>> >>> >>> *[ 2629.259630] bone_capemgr bone_capemgr: part_number >>> 'EBB-GPIO-Example-00A0', version 'N/A'[ 2629.259679] bone_capemgr >>> bone_capemgr: slot #11: override[ 2629.259700] bone_capemgr bone_capemgr: >>> Using override eeprom data at slot 11[ 2629.259722] bone_capemgr >>> bone_capemgr: slot #11: 'Override Board Name,00A0,Override >>> Manuf,EBB-GPIO-Example'[ 2629.271307] gpio-of-helper ocp:gpio_helper: >>> ready[ 2629.271555] bone_capemgr bone_capemgr: slot #11: dtbo >>> 'EBB-GPIO-Example-00A0.dtbo' loaded; overlay id #0* >>> >>> >>> >>> So any help guys would be really appreciated! I am thinking that I must >>> be just doing something wrong. Perhaps the example device tree I am using >>> is outdated? Would someone be willing to share with me a GPIO device tree >>> that works with kernel 4.1? Also I have tried the dt builder online: >>> >>> >>> http://kilobaser.com/blog/2014-07-28-beaglebone-black-devicetreeoverlay-generator#1gpiodto >>> >>> But this seems to not work also. Thanks again everyone. >>> >>> >>> Riley >>> >>> On Thu, Nov 26, 2015 at 2:13 PM, John Syne <[email protected]> wrote: >>> >>>> That is strange because it seems to be working for everyone else. What >>>> is your kernel version? >>>> >>>> If you are using kernel version 4.1 or higher, then do the following on >>>> your BBB >>>> >>>> git clone https://github.com/RobertCNelson/bb.org-overlays.git >>>> >>>> Follow the instructions readme.md file. My guess is you don’t have the >>>> correct Device Tree Compiler, but this repo will install the correct >>>> version. >>>> >>>> Regards, >>>> John >>>> >>>> >>>> >>>> >>>> On Nov 26, 2015, at 8:35 AM, Riley Porter <[email protected]> >>>> wrote: >>>> >>>> Hey guys, >>>> >>>> I have been fighting this for a few days now. But it seems to me that >>>> no matter what I do I cannot get the pinmux'ing to work when applying >>>> overlays in debian. I have tried 7.8 and 8.2 and either is really >>>> different. >>>> >>>> I was looking around to see if I was the only one in this boat and it >>>> turns out I found a post on stack exchange that describes my issue >>>> perfectly. >>>> >>>> Unfortunately the "answer" was to install angstrom. I was hoping >>>> someone on the list would have some secret answer as to why applying an >>>> overlay was not changing the pinmux's? >>>> >>>> I would very much like to stick with debian but if the answer is go >>>> back angstrom I guess I can live with that. >>>> >>>> Thanks >>>> >>>> -- >>>> For more options, visit http://beagleboard.org/discuss >>>> --- >>>> You received this message because you are subscribed to the Google >>>> Groups "BeagleBoard" group. >>>> To unsubscribe from this group and stop receiving emails from it, send >>>> an email to [email protected]. >>>> For more options, visit https://groups.google.com/d/optout. >>>> >>>> >>>> >>>> -- >>>> For more options, visit http://beagleboard.org/discuss >>>> --- >>>> You received this message because you are subscribed to the Google >>>> Groups "BeagleBoard" group. >>>> To unsubscribe from this group and stop receiving emails from it, send >>>> an email to [email protected]. >>>> For more options, visit https://groups.google.com/d/optout. >>>> >>> >>> >>> -- >>> For more options, visit http://beagleboard.org/discuss >>> --- >>> You received this message because you are subscribed to the Google >>> Groups "BeagleBoard" group. >>> To unsubscribe from this group and stop receiving emails from it, send >>> an email to [email protected]. >>> For more options, visit https://groups.google.com/d/optout. >>> >> >> >> -- >> For more options, visit http://beagleboard.org/discuss >> --- >> You received this message because you are subscribed to the Google Groups >> "BeagleBoard" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to [email protected]. >> For more options, visit https://groups.google.com/d/optout. >> > > > -- > For more options, visit http://beagleboard.org/discuss > --- > You received this message because you are subscribed to the Google Groups > "BeagleBoard" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > For more options, visit https://groups.google.com/d/optout. > > > > -- > For more options, visit http://beagleboard.org/discuss > --- > You received this message because you are subscribed to the Google Groups > "BeagleBoard" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > For more options, visit https://groups.google.com/d/optout. > -- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/d/optout.
