Hi All,
getting following error message while beaglebone strating.
can u pl kind help me how to resolve and one more thing is all four user
leds are not blinking even after powerup the board
U-Boot SPL 2013.04-dirty (Jun 19 2013 -
09:57:14)
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx,
SoftConn)
musb-hdrc: MHDRC RTL version
2.0
musb-hdrc: setup fifo_mode
4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Peripheral mode controller at 47401000 using PIO, IRQ 0
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx,
SoftConn)
musb-hdrc: MHDRC RTL version 2.0
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Host mode controller at 47401800 using PIO, IRQ 0
OMAP SD/MMC: 0
mmc_send_cmd : timeout: No status update
reading u-boot.img
reading u-boot.img
U-Boot 2013.04-dirty (Jun 19 2013 - 09:57:14)
I2C: ready
DRAM: 512 MiB
WARNING: Caches not enabled
NAND: No NAND device found!!!
0 MiB
MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1
*** Warning - readenv() failed, using default environment
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx,
SoftConn)
musb-hdrc: MHDRC RTL version 2.0
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Peripheral mode controller at 47401000 using PIO, IRQ 0
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx,
SoftConn)
musb-hdrc: MHDRC RTL version 2.0
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Host mode controller at 47401800 using PIO, IRQ 0
Net: <ethaddr> not set. Validating first E-fuse MAC
Phy not found
PHY reset timed out
cpsw, usb_ether
Hit any key to stop autoboot: 0
U-Boot#
U-Boot#
U-Boot#
U-Boot# U-Boot 2013.04-dirty (Jun 19 2013 - 09:57:14)
Unknown command 'U-Boot' - try 'help'
U-Boot#
Unknown command 'U-Boot' - try 'help'
U-Boot#
Unknown command 'U-Boot' - try 'help'
U-Boot#
Unknown command 'U-Boot' - try 'help'
U-Boot# I2C: read1#### U-Boot 2013.04-dirty (Jun 19 2013 - 09:57:14####
I2C: read1#### U-Boot 2013.04-dirty (Jun 19 2013 - 09:57:14#### I2C:
read1#### U-Boot 2013.04-dirty (Jun 19 2013 - 09:57:14###0
CTRL-A Z for help | 115200 8N1 | NOR | Minicom 2.7 | VT102 | Offline |
ttyUSB0
--
For more options, visit http://beagleboard.org/discuss
---
You received this message because you are subscribed to the Google Groups
"BeagleBoard" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to [email protected].
For more options, visit https://groups.google.com/d/optout.
