dmesg was truncated at the end of my last reply - will try again:
ubuntu@arm:~$ dmesg
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 4.4.9-ti-r25 (root@b3-jetson-tk1-2gb) (gcc
version 5.3.1 20160413 (Ubuntu/Linaro 5.3.1-14ubuntu2) ) #1 SMP Fri May 6
10:28:56 UTC 2016
[ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7),
cr=50c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing
instruction cache
[ 0.000000] Machine model: TI AM335x BeagleBone Black
[ 0.000000] cma: Reserved 24 MiB at 0x9e000000
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] On node 0 totalpages: 130560
[ 0.000000] free_area_init_node: node 0, pgdat c0c299c0, node_mem_map
df96d000
[ 0.000000] Normal zone: 1152 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 130560 pages, LIFO batch:31
[ 0.000000] CPU: All CPU(s) started in SVC mode.
[ 0.000000] AM335X ES2.0 (sgx neon )
[ 0.000000] PERCPU: Embedded 13 pages/cpu @df923000 s24268 r8192 d20788
u53248
[ 0.000000] pcpu-alloc: s24268 r8192 d20788 u53248 alloc=13*4096
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
Total pages: 129408
[ 0.000000] Kernel command line: console=ttyO0,115200n8
root=UUID=14a9c7d7-9990-49c6-92e1-7650b64af3fe ro rootfstype=ext4 rootwait
coherent_pool=1M quiet cape_universal=enable
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144
bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072
bytes)
[ 0.000000] Memory: 474396K/522240K available (7311K kernel code, 913K
rwdata, 3700K rodata, 588K init, 906K bss, 23268K reserved, 24576K
cma-reserved, 0K highmem)
[ 0.000000] Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
vmalloc : 0xe0800000 - 0xff800000 ( 496 MB)
lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
modules : 0xbf800000 - 0xbfe00000 ( 6 MB)
.text : 0xc0008000 - 0xc0ac9000 (11012 kB)
.init : 0xc0ac9000 - 0xc0b5c000 ( 588 kB)
.data : 0xc0b5c000 - 0xc0c40658 ( 914 kB)
.bss : 0xc0c43000 - 0xc0d25b50 ( 907 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] Build-time adjustment of leaf fanout to 32.
[ 0.000000] RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=1
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128
interrupts
[ 0.000000] OMAP clockevent source: timer2 at 24000000 Hz
[ 0.000011] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every
89478484971ns
[ 0.000029] clocksource: timer1: mask: 0xffffffff max_cycles:
0xffffffff, max_idle_ns: 79635851949 ns
[ 0.000041] OMAP clocksource: timer1 at 24000000 Hz
[ 0.000220] Console: colour dummy device 80x30
[ 0.000245] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0'
[ 0.000253] This ensures that you still see kernel messages. Please
[ 0.000259] update your kernel commandline.
[ 0.000277] Calibrating delay loop... 995.32 BogoMIPS (lpj=1990656)
[ 0.046911] pid_max: default: 32768 minimum: 301
[ 0.047047] Security Framework initialized
[ 0.047060] Yama: becoming mindful.
[ 0.047092] AppArmor: AppArmor disabled by boot time parameter
[ 0.047253] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.047266] Mountpoint-cache hash table entries: 1024 (order: 0, 4096
bytes)
[ 0.048036] Initializing cgroup subsys io
[ 0.048067] Initializing cgroup subsys memory
[ 0.048107] Initializing cgroup subsys devices
[ 0.048123] Initializing cgroup subsys freezer
[ 0.048138] Initializing cgroup subsys net_cls
[ 0.048152] Initializing cgroup subsys perf_event
[ 0.048166] Initializing cgroup subsys net_prio
[ 0.048180] Initializing cgroup subsys pids
[ 0.048236] CPU: Testing write buffer coherency: ok
[ 0.048289] ftrace: allocating 33920 entries in 67 pages
[ 0.132378] CPU0: thread -1, cpu 0, socket -1, mpidr 0
[ 0.132506] Setting up static identity map for 0x80008240 - 0x8000828c
[ 0.135970] Brought up 1 CPUs
[ 0.135992] SMP: Total of 1 processors activated (995.32 BogoMIPS).
[ 0.136000] CPU: All CPU(s) started in SVC mode.
[ 0.137425] devtmpfs: initialized
[ 0.155546] VFP support v0.3: implementor 41 architecture 3 part 30
variant c rev 3
[ 0.173699] omap_hwmod: debugss: _wait_target_disable failed
[ 0.227391] clocksource: jiffies: mask: 0xffffffff max_cycles:
0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.229453] xor: measuring software checksum speed
[ 0.266913] arm4regs : 1221.000 MB/sec
[ 0.306908] 8regs : 1093.000 MB/sec
[ 0.346907] 32regs : 1055.000 MB/sec
[ 0.386908] neon : 1759.000 MB/sec
[ 0.386915] xor: using function: neon (1759.000 MB/sec)
[ 0.387011] pinctrl core: initialized pinctrl subsystem
[ 0.388952] NET: Registered protocol family 16
[ 0.392418] DMA: preallocated 1024 KiB pool for atomic coherent
allocations
[ 0.393615] cpuidle: using governor ladder
[ 0.393637] cpuidle: using governor menu
[ 0.398750] OMAP GPIO hardware version 0.1
[ 0.411210] No ATAGs?
[ 0.411242] hw-breakpoint: debug architecture 0x4 unsupported.
[ 0.411816] omap4_sram_init:Unable to allocate sram needed to handle
errata I688
[ 0.411830] omap4_sram_init:Unable to get sram pool needed to handle
errata I688
[ 0.491022] raid6: int32x1 gen() 269 MB/s
[ 0.559065] raid6: int32x1 xor() 192 MB/s
[ 0.627007] raid6: int32x2 gen() 392 MB/s
[ 0.694982] raid6: int32x2 xor() 235 MB/s
[ 0.762927] raid6: int32x4 gen() 429 MB/s
[ 0.830995] raid6: int32x4 xor() 272 MB/s
[ 0.899071] raid6: int32x8 gen() 367 MB/s
[ 0.966983] raid6: int32x8 xor() 239 MB/s
[ 1.034918] raid6: neonx1 gen() 1452 MB/s
[ 1.102934] raid6: neonx1 xor() 846 MB/s
[ 1.170914] raid6: neonx2 gen() 1788 MB/s
[ 1.238914] raid6: neonx2 xor() 1146 MB/s
[ 1.306929] raid6: neonx4 gen() 1205 MB/s
[ 1.374931] raid6: neonx4 xor() 995 MB/s
[ 1.442917] raid6: neonx8 gen() 924 MB/s
[ 1.510913] raid6: neonx8 xor() 804 MB/s
[ 1.510920] raid6: using algorithm neonx2 gen() 1788 MB/s
[ 1.510927] raid6: .... xor() 1146 MB/s, rmw enabled
[ 1.510934] raid6: using intx1 recovery algorithm
[ 1.519796] edma 49000000.edma: TI EDMA DMA engine driver
[ 1.524534] SCSI subsystem initialized
[ 1.524917] libata version 3.00 loaded.
[ 1.525256] usbcore: registered new interface driver usbfs
[ 1.525333] usbcore: registered new interface driver hub
[ 1.525430] usbcore: registered new device driver usb
[ 1.525991] omap_i2c 44e0b000.i2c: could not find pctldev for node
/ocp/l4_wkup@44c00000/scm@210000/pinmux@800/pinmux_i2c0_pins, deferring
probe
[ 1.526036] omap_i2c 4819c000.i2c: could not find pctldev for node
/ocp/l4_wkup@44c00000/scm@210000/pinmux@800/pinmux_i2c2_pins, deferring
probe
[ 1.526156] media: Linux media interface: v0.10
[ 1.526216] Linux video capture interface: v2.00
[ 1.526304] pps_core: LinuxPPS API ver. 1 registered
[ 1.526311] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo
Giometti <[email protected]>
[ 1.526337] PTP clock support registered
[ 1.527222] omap-mailbox 480c8000.mailbox: omap mailbox rev 0x400
[ 1.528442] NetLabel: Initializing
[ 1.528456] NetLabel: domain hash size = 128
[ 1.528462] NetLabel: protocols = UNLABELED CIPSOv4
[ 1.528518] NetLabel: unlabeled traffic allowed by default
[ 1.528891] clocksource: Switched to clocksource timer1
[ 1.636226] NET: Registered protocol family 2
[ 1.637076] TCP established hash table entries: 4096 (order: 2, 16384
bytes)
[ 1.637125] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 1.637183] TCP: Hash tables configured (established 4096 bind 4096)
[ 1.637252] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 1.637272] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 1.637567] NET: Registered protocol family 1
[ 1.638097] RPC: Registered named UNIX socket transport module.
[ 1.638109] RPC: Registered udp transport module.
[ 1.638116] RPC: Registered tcp transport module.
[ 1.638122] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.638701] Unpacking initramfs...
[ 1.956187] Freeing initrd memory: 4392K (cfbb6000 - d0000000)
[ 1.956847] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5
counters available
[ 1.959374] futex hash table entries: 256 (order: 2, 16384 bytes)
[ 1.959495] audit: initializing netlink subsys (disabled)
[ 1.959571] audit: type=2000 audit(1.896:1): initialized
[ 1.969311] zbud: loaded
[ 1.969940] VFS: Disk quotas dquot_6.6.0
[ 1.970185] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096
bytes)
[ 1.972770] NFS: Registering the id_resolver key type
[ 1.972831] Key type id_resolver registered
[ 1.972839] Key type id_legacy registered
[ 1.972939] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 1.973285] fuse init (API version 7.23)
[ 1.973898] SGI XFS with ACLs, security attributes, realtime, no debug
enabled
[ 1.981491] Block layer SCSI generic (bsg) driver version 0.4 loaded
(major 249)
[ 1.981717] io scheduler noop registered
[ 1.981733] io scheduler deadline registered
[ 1.981796] io scheduler cfq registered (default)
[ 1.983126] pinctrl-single 44e10800.pinmux: 142 pins at pa f9e10800 size
568
[ 1.984568] wkup_m3_ipc 44e11324.wkup_m3_ipc: could not get rproc handle
[ 1.985984] Serial: 8250/16550 driver, 6 ports, IRQ sharing disabled
[ 1.988763] 44e09000.serial: ttyS0 at MMIO 0x44e09000 (irq = 158,
base_baud = 3000000) is a 8250
[ 1.996391] console [ttyS0] enabled
[ 1.997931] [drm] Initialized drm 1.1.0 20060810
[ 2.048963] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6
[ 2.048984] davinci_mdio 4a101000.mdio: detected phy mask fffffffe
[ 2.049327] davinci_mdio: dt: updated phy_id[0] from phy_mask[fffffffe]
[ 2.056663] libphy: 4a101000.mdio: probed
[ 2.056695] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00,
driver SMSC LAN8710/LAN8720
[ 2.057526] cpsw 4a100000.ethernet: Detected MACID = 90:59:af:56:ea:16
[ 2.059202] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.059256] ehci-platform: EHCI generic platform driver
[ 2.059436] ehci-omap: OMAP-EHCI Host Controller driver
[ 2.059845] usbcore: registered new interface driver usb-storage
[ 2.061636] 47401300.usb-phy supply vcc not found, using dummy regulator
[ 2.063800] musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine,
bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn)
[ 2.063816] musb-hdrc: MHDRC RTL version 2.0
[ 2.063824] musb-hdrc: setup fifo_mode 4
[ 2.063842] musb-hdrc: 28/31 max ep, 16384/16384 memory
[ 2.065101] 47401b00.usb-phy supply vcc not found, using dummy regulator
[ 2.067115] musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine,
bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn)
[ 2.067129] musb-hdrc: MHDRC RTL version 2.0
[ 2.067136] musb-hdrc: setup fifo_mode 4
[ 2.067150] musb-hdrc: 28/31 max ep, 16384/16384 memory
[ 2.067281] musb-hdrc musb-hdrc.1.auto: MUSB HDRC host driver
[ 2.067314] musb-hdrc musb-hdrc.1.auto: new USB bus registered, assigned
bus number 1
[ 2.067574] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.067586] usb usb1: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 2.067596] usb usb1: Product: MUSB HDRC host driver
[ 2.067605] usb usb1: Manufacturer: Linux 4.4.9-ti-r25 musb-hcd
[ 2.067614] usb usb1: SerialNumber: musb-hdrc.1.auto
[ 2.068406] hub 1-0:1.0: USB hub found
[ 2.068457] hub 1-0:1.0: 1 port detected
[ 2.077816] mousedev: PS/2 mouse device common for all mice
[ 2.080083] omap_rtc 44e3e000.rtc: rtc core: registered 44e3e000.rtc as
rtc0
[ 2.080859] i2c /dev entries driver
[ 2.082575] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60
sec
[ 2.083365] omap_hsmmc 48060000.mmc: Got CD GPIO
[ 2.146269] hidraw: raw HID events driver (C) Jiri Kosina
[ 2.146897] usbcore: registered new interface driver usbhid
[ 2.146909] usbhid: USB HID core driver
[ 2.147163] ashmem: initialized
[ 2.147930] remoteproc0: wkup_m3 is available
[ 2.147943] remoteproc0: Note: remoteproc is still under development
and considered experimental.
[ 2.147950] remoteproc0: THE BINARY FORMAT IS NOT YET FINALIZED, and
backward compatibility isn't yet guaranteed.
[ 2.151512] NET: Registered protocol family 10
[ 2.156211] mip6: Mobile IPv6
[ 2.156239] NET: Registered protocol family 17
[ 2.156361] Key type dns_resolver registered
[ 2.156376] mpls_gso: MPLS GSO support
[ 2.156646] omap_voltage_late_init: Voltage driver support not added
[ 2.164071] PM: Cannot get wkup_m3_ipc handle
[ 2.168857] ThumbEE CPU extension supported.
[ 2.168996] Registering SWP/SWPB emulation handler
[ 2.170068] registered taskstats version 1
[ 2.170308] zswap: loaded using pool lzo/zbud
[ 2.176631] Btrfs loaded
[ 2.199927] Key type encrypted registered
[ 2.202852] input: tps65217_pwr_but as
/devices/platform/ocp/44e0b000.i2c/i2c-0/0-0024/input/input0
[ 2.203019] mmc1: MAN_BKOPS_EN bit is not set
[ 2.204841] mmc1: new high speed MMC card at address 0001
[ 2.205805] mmcblk0: mmc1:0001 MMC02G 1.79 GiB
[ 2.206190] mmcblk0boot0: mmc1:0001 MMC02G partition 1 1.00 MiB
[ 2.206551] mmcblk0boot1: mmc1:0001 MMC02G partition 2 1.00 MiB
[ 2.208363] mmcblk0: p1
[ 2.226164] tps65217 0-0024: TPS65217 ID 0xe version 1.2
[ 2.226687] at24 0-0050: 32768 byte 24c256 EEPROM, writable, 1
bytes/write
[ 2.226915] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz
[ 2.228507] at24 2-0054: 32768 byte 24c256 EEPROM, writable, 1
bytes/write
[ 2.228971] at24 2-0055: 32768 byte 24c256 EEPROM, writable, 1
bytes/write
[ 2.229364] at24 2-0056: 32768 byte 24c256 EEPROM, writable, 1
bytes/write
[ 2.229735] at24 2-0057: 32768 byte 24c256 EEPROM, writable, 1
bytes/write
[ 2.229772] omap_i2c 4819c000.i2c: bus 2 rev0.11 at 100 kHz
[ 2.230801] remoteproc0: powering up wkup_m3
[ 2.230862] remoteproc0: Booting fw image am335x-pm-firmware.elf, size
219735
[ 2.231109] remoteproc0: remote processor wkup_m3 is now up
[ 2.231131] wkup_m3_ipc 44e11324.wkup_m3_ipc: CM3 Firmware Version =
0x191
[ 2.236833] bone_capemgr bone_capemgr: Baseboard:
'A335BNLT,0A5C,2713BBBK7164'
[ 2.236863] bone_capemgr bone_capemgr:
compatible-baseboard=ti,beaglebone-black - #slots=4
[ 2.276906] bone_capemgr bone_capemgr: slot #0: No cape found
[ 2.320900] bone_capemgr bone_capemgr: slot #1: No cape found
[ 2.364897] bone_capemgr bone_capemgr: slot #2: No cape found
[ 2.408945] bone_capemgr bone_capemgr: slot #3: No cape found
[ 2.414886] bone_capemgr bone_capemgr: initialized OK.
[ 2.416525] PM: bootloader does not support rtc-only!
[ 2.417104] omap_rtc 44e3e000.rtc: setting system clock to 2000-01-01
00:00:00 UTC (946684800)
[ 2.417130] of_cfs_init
[ 2.417242] of_cfs_init: OK
[ 2.422459] PM: Hibernation image not present or could not be loaded.
[ 2.423630] Freeing unused kernel memory: 588K (c0ac9000 - c0b5c000)
[ 2.469877] usb 1-1: new high-speed USB device number 2 using musb-hdrc
[ 2.518781] random: systemd-udevd urandom read with 13 bits of entropy
available
[ 2.598431] usb 1-1: New USB device found, idVendor=7392, idProduct=7811
[ 2.598455] usb 1-1: New USB device strings: Mfr=1, Product=2,
SerialNumber=3
[ 2.598464] usb 1-1: Product: 802.11n WLAN Adapter
[ 2.598473] usb 1-1: Manufacturer: Realtek
[ 2.598482] usb 1-1: SerialNumber: 00e04c000001
[ 3.152138] tda998x 0-0070: found TDA19988
[ 3.161279] tilcdc 4830e000.lcdc: bound 0-0070 (ops tda998x_ops
[tda998x])
[ 3.161309] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 3.161316] [drm] No driver support for vblank timestamp query.
[ 3.161747] tilcdc 4830e000.lcdc: No connectors reported connected with
modes
[ 3.161770] [drm] Cannot find any crtc or sizes - going 1024x768
[ 3.189859] Console: switching to colour frame buffer device 128x48
[ 3.226710] tilcdc 4830e000.lcdc: fb0: frame buffer device
[ 3.226741] [drm] Initialized tilcdc 1.0.0 20121205 on minor 0
[ 3.560342] EXT4-fs (mmcblk0p1): INFO: recovery required on readonly
filesystem
[ 3.560365] EXT4-fs (mmcblk0p1): write access will be enabled during
recovery
[ 3.926543] EXT4-fs (mmcblk0p1): recovery complete
[ 3.930268] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data
mode. Opts: (null)
[ 4.320148] systemd[1]: System time before build time, advancing clock.
[ 4.472637] systemd[1]: systemd 229 running in system mode. (+PAM +AUDIT
+SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT
+GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN)
[ 4.473468] systemd[1]: Detected architecture arm.
[ 4.474936] systemd[1]: Set hostname to <arm>.
[ 4.972515] systemd[1]: Started Dispatch Password Requests to Console
Directory Watch.
[ 4.973312] systemd[1]: Listening on /dev/initctl Compatibility Named
Pipe.
[ 4.974325] systemd[1]: Created slice User and Session Slice.
[ 4.974492] systemd[1]: Reached target Swap.
[ 4.974802] systemd[1]: Listening on Syslog Socket.
[ 4.975157] systemd[1]: Started Forward Password Requests to Wall
Directory Watch.
[ 4.975271] systemd[1]: Reached target Remote File Systems (Pre).
[ 4.975360] systemd[1]: Reached target Encrypted Volumes.
[ 4.976136] systemd[1]: Created slice System Slice.
[ 4.977248] systemd[1]: Created slice system-getty.slice.
[ 4.977389] systemd[1]: Reached target Slices.
[ 4.977756] systemd[1]: Listening on udev Control Socket.
[ 4.978629] systemd[1]: Created slice system-serial\x2dgetty.slice.
[ 4.980352] systemd[1]: Set up automount Arbitrary Executable File
Formats File System Automount Point.
[ 4.980645] systemd[1]: Listening on fsck to fsckd communication Socket.
[ 4.980758] systemd[1]: Reached target Remote File Systems.
[ 4.981239] systemd[1]: Listening on udev Kernel Socket.
[ 4.981592] systemd[1]: Listening on Journal Socket.
[ 4.985926] systemd[1]: Starting Create list of required static device
nodes for the current kernel...
[ 4.999181] systemd[1]: Starting Load Kernel Modules...
[ 5.053457] systemd[1]: Started Read required files in advance.
[ 5.109367] systemd[1]: Mounting POSIX Message Queue File System...
[ 5.116701] systemd[1]: Starting File System Check on Root Device...
[ 5.193287] systemd[1]: Mounting /sys/kernel/debug...
[ 5.206265] systemd[1]: Listening on Journal Audit Socket.
[ 5.206727] systemd[1]: Listening on Journal Socket (/dev/log).
[ 5.261341] systemd[1]: Starting Journal Service...
[ 5.323715] systemd[1]: Mounted POSIX Message Queue File System.
[ 5.324003] systemd[1]: Mounted /sys/kernel/debug.
[ 5.332096] systemd[1]: Started Create list of required static device
nodes for the current kernel.
[ 5.337355] systemd[1]: Started Load Kernel Modules.
[ 5.340306] systemd[1]: ureadahead.service: Main process exited,
code=exited, status=5/NOTINSTALLED
[ 5.342835] systemd[1]: ureadahead.service: Unit entered failed state.
[ 5.343039] systemd[1]: ureadahead.service: Failed with result
'exit-code'.
[ 5.461323] systemd[1]: Started File System Check on Root Device.
[ 5.602725] systemd[1]: Started Journal Service.
[ 6.042592] EXT4-fs (mmcblk0p1): re-mounted. Opts: errors=remount-ro
[ 7.647553] systemd-journald[177]: Received request to flush runtime
journal from PID 1
[ 11.307078] Bluetooth: Core ver 2.21
[ 11.307219] NET: Registered protocol family 31
[ 11.307229] Bluetooth: HCI device and connection manager initialized
[ 11.307254] Bluetooth: HCI socket layer initialized
[ 11.307271] Bluetooth: L2CAP socket layer initialized
[ 11.307315] Bluetooth: SCO socket layer initialized
[ 11.548958] random: nonblocking pool is initialized
[ 11.867622] omap_rng 48310000.rng: OMAP Random Number Generator ver. 20
[ 11.971773] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2
[ 12.052357] ti-pruss 4a300000.pruss: creating PRU cores and other child
platform devices
[ 12.074195] omap-sham 53100000.sham: hw accel on OMAP rev 4.3
[ 12.257706] net eth0: initializing cpsw version 1.12 (0)
[ 12.264151] net eth0: phy found : id is : 0x7c0f1
[ 12.297388] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 12.329420] remoteproc1: 4a334000.pru0 is available
[ 12.329447] remoteproc1: Note: remoteproc is still under development
and considered experimental.
[ 12.329455] remoteproc1: THE BINARY FORMAT IS NOT YET FINALIZED, and
backward compatibility isn't yet guaranteed.
[ 12.332237] remoteproc1: Direct firmware load for am335x-pru0-fw failed
with error -2
[ 12.332268] remoteproc1: failed to load am335x-pru0-fw
[ 12.379883] pru-rproc 4a334000.pru0: booting the PRU core manually
[ 12.379910] remoteproc1: powering up 4a334000.pru0
[ 12.379975] remoteproc1: Direct firmware load for am335x-pru0-fw failed
with error -2
[ 12.379990] remoteproc1: request_firmware failed: -2
[ 12.385195] pru-rproc 4a334000.pru0: rproc_boot failed
[ 12.881715] asoc-simple-card sound: i2s-hifi <-> 48038000.mcasp mapping
ok
[ 12.909256] remoteproc1: releasing 4a334000.pru0
[ 12.909419] pru-rproc: probe of 4a334000.pru0 failed with error -2
[ 12.909733] remoteproc1: 4a338000.pru1 is available
[ 12.909745] remoteproc1: Note: remoteproc is still under development
and considered experimental.
[ 12.909754] remoteproc1: THE BINARY FORMAT IS NOT YET FINALIZED, and
backward compatibility isn't yet guaranteed.
[ 12.911320] remoteproc1: Direct firmware load for am335x-pru1-fw failed
with error -2
[ 12.911349] remoteproc1: failed to load am335x-pru1-fw
[ 12.931998] pru-rproc 4a338000.pru1: booting the PRU core manually
[ 12.932025] remoteproc1: powering up 4a338000.pru1
[ 12.932084] remoteproc1: Direct firmware load for am335x-pru1-fw failed
with error -2
[ 12.932098] remoteproc1: request_firmware failed: -2
[ 12.937338] pru-rproc 4a338000.pru1: rproc_boot failed
[ 13.253329] remoteproc1: releasing 4a338000.pru1
[ 13.253493] pru-rproc: probe of 4a338000.pru1 failed with error -2
[ 14.905156] net eth0: initializing cpsw version 1.12 (0)
[ 14.907553] net eth0: phy found : id is : 0x7c0f1
[ 14.923777] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 15.340408] using random self ethernet address
[ 15.340433] using random host ethernet address
[ 15.340448] using host ethernet address: 90:59:AF:56:EA:18
[ 15.340456] using self ethernet address: 90:59:AF:56:EA:10
[ 15.350388] usb0: HOST MAC 90:59:af:56:ea:18
[ 15.351109] usb0: MAC 90:59:af:56:ea:10
[ 15.351268] using random self ethernet address
[ 15.351283] using random host ethernet address
[ 15.351409] g_ether gadget: Ethernet Gadget, version: Memorial Day 2008
[ 15.351420] g_ether gadget: g_ether ready
[ 15.677899] IPv6: ADDRCONF(NETDEV_UP): usb0: link is not ready
[ 16.135210] rtl8192cu: Chip version 0x10
[ 16.688167] rtl8192cu: MAC address: 80:1f:02:a6:93:cf
[ 16.688199] rtl8192cu: Board Type 0
[ 16.688330] rtl_usb: rx_max_size 15360, rx_urb_num 8, in_ep 1
[ 16.688490] rtl8192cu: Loading firmware rtlwifi/rtl8192cufw_TMSC.bin
[ 16.822937] ieee80211 phy0: Selected rate control algorithm 'rtl_rc'
[ 16.848090] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 16.857465] usbcore: registered new interface driver rtl8192cu
[ 18.787106] cfg80211: World regulatory domain updated:
[ 18.787136] cfg80211: DFS Master region: unset
[ 18.787144] cfg80211: (start_freq - end_freq @ bandwidth),
(max_antenna_gain, max_eirp), (dfs_cac_time)
[ 18.787157] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A,
2000 mBm), (N/A)
[ 18.787167] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A,
2000 mBm), (N/A)
[ 18.787176] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A,
2000 mBm), (N/A)
[ 18.787187] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000
KHz AUTO), (N/A, 2000 mBm), (N/A)
[ 18.787198] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000
KHz AUTO), (N/A, 2000 mBm), (0 s)
[ 18.787207] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A,
2000 mBm), (0 s)
[ 18.787216] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A,
2000 mBm), (N/A)
[ 18.787225] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz),
(N/A, 0 mBm), (N/A)
[ 320.658705] rtl8192cu: MAC auto ON okay!
[ 320.770449] rtl8192cu: Tx queue select: 0x05
[ 321.339570] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 338.101261] rtl8192cu: MAC auto ON okay!
[ 338.204702] rtl8192cu: Tx queue select: 0x05
[ 338.896465] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 341.069943] wlan0: authenticate with 08:60:6e:ba:6d:e0
[ 341.089020] wlan0: send auth to 08:60:6e:ba:6d:e0 (try 1/3)
[ 341.094276] wlan0: authenticated
[ 341.101068] wlan0: associate with 08:60:6e:ba:6d:e0 (try 1/3)
[ 341.104854] wlan0: RX AssocResp from 08:60:6e:ba:6d:e0 (capab=0x411
status=0 aid=1)
[ 341.214684] wlan0: associated
[ 341.231684] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
ubuntu@arm:~$
--
For more options, visit http://beagleboard.org/discuss
---
You received this message because you are subscribed to the Google Groups
"BeagleBoard" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to [email protected].
To view this discussion on the web visit
https://groups.google.com/d/msgid/beagleboard/d178feba-ff5b-48c9-8689-3d83c67b7a47%40googlegroups.com.
For more options, visit https://groups.google.com/d/optout.
