Hi Robert,
I tested debian-9.6 from the link you provided, and the colors on my clone
board are still inverted.
I tested the same image on beaglebone and the colors were correct.
Please see my log below for the clone:
U-Boot 2018.09-00002-gd5b4c4b656 (Oct 19 2018 - 14:16:02 -0500), Build:
jenkins-
github_Bootloader-Builder-84
CPU : AM335X-GP rev
2.1
I2C:
ready
DRAM: 512
MiB
No match for driver
'omap_hsmmc'
No match for driver
'omap_hsmmc'
Some drivers were not
found
Reset Source: Global warm SW reset has
occurred.
Reset Source: Power-on reset has
occurred.
RTC 32KCLK Source:
External.
MMC: OMAP SD/MMC: 0, OMAP SD/MMC:
1
Loading Environment from EXT4... ** File not found /boot/uboot.env
**
** Unable to read "/boot/uboot.env" from mmc0:1
**
Board: BeagleBone
Black
<ethaddr> not set. Validating first E-fuse
MAC
BeagleBone
Black:
Timed out in wait_for_event:
status=0000
Check if pads/pull-ups of bus are properly
configured
BeagleBone: cape eeprom: i2c_probe:
0x54:
Timed out in wait_for_event:
status=0000
Check if pads/pull-ups of bus are properly
configured
BeagleBone: cape eeprom: i2c_probe:
0x55:
Timed out in wait_for_event:
status=0000
Check if pads/pull-ups of bus are properly
configured
BeagleBone: cape eeprom: i2c_probe:
0x56:
Timed out in wait_for_event:
status=0000
Check if pads/pull-ups of bus are properly
configured
BeagleBone: cape eeprom: i2c_probe:
0x57:
Net: eth0: MII
MODE
cpsw,
usb_ether
Press SPACE to abort autoboot in 2
seconds
board_name=[A335BNLT]
...
board_rev=[000C]
...
switch to partitions #0,
OK
mmc0 is current
device
SD/MMC found on device
0
switch to partitions #0,
OK
mmc0 is current
device
Scanning mmc
0:1...
gpio: pin 56 (gpio 56) value is
0
gpio: pin 55 (gpio 55) value is
0
gpio: pin 54 (gpio 54) value is
0
gpio: pin 53 (gpio 53) value is
1
switch to partitions #0,
OK
mmc0 is current
device
gpio: pin 54 (gpio 54) value is
1
Checking for: /uEnv.txt
...
Checking for: /boot.scr
...
Checking for: /boot/boot.scr
...
Checking for: /boot/uEnv.txt
...
gpio: pin 55 (gpio 55) value is
1
2117 bytes read in 19 ms (108.4
KiB/s)
Loaded environment from
/boot/uEnv.txt
debug: [dtb=am335x-boneblack.dtb]
...
Using: dtb=am335x-boneblack.dtb
...
Checking if uname_r is set in
/boot/uEnv.txt...
gpio: pin 56 (gpio 56) value is
1
Running uname_boot
...
loading /boot/vmlinuz-4.14.79-ti-r86
...
9712128 bytes read in 632 ms (14.7
MiB/s)
debug: [enable_uboot_overlays=1]
...
debug: [enable_uboot_cape_universal=1]
...
debug: [uboot_base_dtb_univ=am335x-boneblack-uboot-univ.dtb]
...
uboot_overlays: [uboot_base_dtb=am335x-boneblack-uboot-univ.dtb]
...
uboot_overlays: Switching too: dtb=am335x-boneblack-uboot-univ.dtb
...
loading /boot/dtbs/4.14.79-ti-r86/am335x-boneblack-uboot-univ.dtb
...
161719 bytes read in 57 ms (2.7
MiB/s)
uboot_overlays: [fdt_buffer=0x60000]
...
uboot_overlays: loading /lib/firmware/BB-BONE-eMMC1-01-00A0.dtbo
...
1440 bytes read in 55 ms (25.4
KiB/s)
uboot_overlays: loading /lib/firmware/BB-HDMI-TDA998x-00A0.dtbo
...
4896 bytes read in 76 ms (62.5
KiB/s)
uboot_overlays: loading /lib/firmware/BB-ADC-00A0.dtbo
...
711 bytes read in 183 ms (2.9
KiB/s)
uboot_overlays: loading /lib/firmware/AM335X-PRU-RPROC-4-14-TI-00A0.dtbo
...
3513 bytes read in 160 ms (20.5
KiB/s)
loading /boot/initrd.img-4.14.79-ti-r86
...
4636329 bytes read in 306 ms (14.4
MiB/s)
debug: [console=ttyO0,115200n8 bone_capemgr.uboot_capemgr_enabled=1
root=/dev/mm
cblk0p1 ro rootfstype=ext4 rootwait coherent_pool=1M net.ifnames=0 quiet
video=H
DMI-A-1:1024x768@60e]
...
debug: [bootz 0x82000000 0x88080000:46bea9 88000000]
...
## Flattened Device Tree blob at
88000000
Booting using the fdt blob at
0x88000000
Loading Ramdisk to 8fb94000, end 8ffffea9 ...
OK
reserving fdt memory region: addr=88000000
size=89000
Loading Device Tree to 8fb08000, end 8fb93fff ...
OK
Starting kernel
...
[ 0.002388] timer_probe: no matching timers
found
[ 1.081030] wkup_m3_ipc 44e11324.wkup_m3_ipc: could not get rproc
handle
[ 1.378727] omap_voltage_late_init: Voltage driver support not
added
[ 1.386104] PM: Cannot get wkup_m3_ipc
handle
[ 1.851328] musb-hdrc musb-hdrc.1: VBUS_ERROR in a_wait_vrise (80,
<SessEnd),
retry #3, port1
0008010c
[ 2.757564] tda998x 0-0070: read edid
timeout
[ 2.856904] hdmi-audio-codec hdmi-audio-codec.0.auto: ASoC: no source
widget
found for
Playback
[ 2.865915] hdmi-audio-codec hdmi-audio-codec.0.auto: ASoC: Failed to
add rou
te Playback -> direct -> TX
[ 5.037791] tda998x 0-0070: read edid
timeout
Debian GNU/Linux 9 beaglebone
ttyS0
BeagleBoard.org Debian Image
2018-12-30
Support/FAQ:
http://elinux.org/Beagleboard:BeagleBoneBlack_Debian
default username:password is
[debian:temppwd]
beaglebone login:
******
I really don't understand why its causing this color invert on the clone
board.
Any suggestions would be greatly appreciated.
Thank you
On Thursday, January 3, 2019 at 1:06:57 PM UTC-7, RobertCNelson wrote:
>
> On Thu, Jan 3, 2019 at 1:56 PM <sam.a...@gmail.com <javascript:>> wrote:
> >
> > Hi Robert,
> >
> > Here below is my boot log:
> > """
> > U-Boot 2018.09-00002-gd5b4c4b656 (Oct 19 2018 - 14:16:02 -0500), Build:
> jenkins-
> > github_Bootloader-Builder-84
> >
> > CPU : AM335X-GP rev 2.1
> > I2C: ready
> > DRAM: 512 MiB
> > No match for driver 'omap_hsmmc'
> > No match for driver 'omap_hsmmc'
> > Some drivers were not found
> > Reset Source: Global warm SW reset has occurred.
> > Reset Source: Power-on reset has occurred.
> > RTC 32KCLK Source: External.
> > MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1
> > Loading Environment from EXT4... ** File not found /boot/uboot.env **
> >
> > ** Unable to read "/boot/uboot.env" from mmc0:1 **
> > Board: BeagleBone Black
> > <ethaddr> not set. Validating first E-fuse MAC
> > BeagleBone Black:
> > Timed out in wait_for_event: status=0000
> > Check if pads/pull-ups of bus are properly configured
> > BeagleBone: cape eeprom: i2c_probe: 0x54:
> > Timed out in wait_for_event: status=0000
> > Check if pads/pull-ups of bus are properly configured
> > BeagleBone: cape eeprom: i2c_probe: 0x55:
> > Timed out in wait_for_event: status=0000
> > Check if pads/pull-ups of bus are properly configured
> > BeagleBone: cape eeprom: i2c_probe: 0x56:
> > Timed out in wait_for_event: status=0000
> > Check if pads/pull-ups of bus are properly configured
> > BeagleBone: cape eeprom: i2c_probe: 0x57:
> > Net: eth0: MII MODE
> > cpsw, usb_ether
> > Press SPACE to abort autoboot in 2 seconds
> > board_name=[A335BNLT] ...
> > board_rev=[000C] ...
> > switch to partitions #0, OK
> > mmc0 is current device
> > SD/MMC found on device 0
> > switch to partitions #0, OK
> > mmc0 is current device
> > Scanning mmc 0:1...
> > gpio: pin 56 (gpio 56) value is 0
> > gpio: pin 55 (gpio 55) value is 0
> > gpio: pin 54 (gpio 54) value is 0
> > gpio: pin 53 (gpio 53) value is 1
> > switch to partitions #0, OK
> > mmc0 is current device
> > gpio: pin 54 (gpio 54) value is 1
> > Checking for: /uEnv.txt ...
> > Checking for: /boot.scr ...
> > Checking for: /boot/boot.scr ...
> > Checking for: /boot/uEnv.txt ...
> > gpio: pin 55 (gpio 55) value is 1
> > 2100 bytes read in 20 ms (102.5 KiB/s)
> > Loaded environment from /boot/uEnv.txt
> > debug: [dtb=am335x-boneblack.dtb] ...
> > Using: dtb=am335x-boneblack.dtb ...
> > Checking if uname_r is set in /boot/uEnv.txt...
> > gpio: pin 56 (gpio 56) value is 1
> > Running uname_boot ...
> > loading /boot/vmlinuz-4.9.45-ti-r57 ...
> > 9464664 bytes read in 612 ms (14.7 MiB/s)
> > debug: [enable_uboot_overlays=1] ...
> > debug: [enable_uboot_cape_universal=1] ...
> > debug: [uboot_base_dtb_univ=am335x-boneblack-uboot-univ.dtb] ...
> > uboot_overlays: [uboot_base_dtb=am335x-boneblack-uboot-univ.dtb] ...
> > debug: unable to find [am335x-boneblack-uboot-univ.dtb] using
> [am335x-boneblack-
> > uboot.dtb] instead ...
> > debug: [uboot_base_dtb_univ=am335x-boneblack-uboot.dtb] ...
> > uboot_overlays: [uboot_base_dtb=am335x-boneblack-uboot.dtb] ...
> > uboot_overlays: Switching too: dtb=am335x-boneblack-uboot.dtb ...
> > loading /boot/dtbs/4.9.45-ti-r57/am335x-boneblack-uboot.dtb ...
> > 55752 bytes read in 36 ms (1.5 MiB/s)
> > uboot_overlays: [fdt_buffer=0x60000] ...
> > uboot_overlays: loading /lib/firmware/BB-BONE-eMMC1-01-00A0.dtbo ...
> > 1440 bytes read in 345 ms (3.9 KiB/s)
> > uboot_overlays: loading /lib/firmware/BB-HDMI-TDA998x-00A0.dtbo ...
> > 4920 bytes read in 219 ms (21.5 KiB/s)
> > uboot_overlays: loading /lib/firmware/BB-ADC-00A0.dtbo ...
> > 711 bytes read in 599 ms (1000 Bytes/s)
> > uboot_overlays: loading /lib/firmware/univ-bbb-EVA-00A0.dtbo ...
> > 61976 bytes read in 644 ms (93.8 KiB/s)
> > loading /boot/initrd.img-4.9.45-ti-r57 ...
> > 6395122 bytes read in 420 ms (14.5 MiB/s)
> > debug: [console=ttyO0,115200n8 bone_capemgr.uboot_capemgr_enabled=1
> root=/dev/mm
> > cblk0p1 ro rootfstype=ext4 rootwait coherent_pool=1M net.ifnames=0 quiet
> video=H
> > DMI-A-1:1024x768@60e] ...
> > debug: [bootz 0x82000000 0x88080000:6194f2 88000000] ...
> > ## Flattened Device Tree blob at 88000000
> > Booting using the fdt blob at 0x88000000
> > Loading Ramdisk to 8f9e6000, end 8ffff4f2 ... OK
> > reserving fdt memory region: addr=88000000 size=7d000
> > Loading Device Tree to 8f966000, end 8f9e5fff ... OK
> >
> > Starting kernel ...
> >
> > [ 0.001790] clocksource_probe: no matching clocksources found
> > [ 2.416644] wkup_m3_ipc 44e11324.wkup_m3_ipc: could not get rproc
> handle
> > [ 2.670204] omap_voltage_late_init: Voltage driver support not added
> > [ 2.677613] PM: Cannot get wkup_m3_ipc handle
> > [ 3.167898] musb-hdrc musb-hdrc.1: VBUS_ERROR in a_wait_vrise (80,
> <SessEnd),
> > retry #3, port1 0008010c
> > [ 4.089472] tda998x 0-0070: read edid timeout
> > [ 4.185191] bone_capemgr bone_capemgr: slot #0: auto loading handled
> by U-Boo
> > t
> > [ 4.192591] bone_capemgr bone_capemgr: slot #1: auto loading handled
> by U-Boo
> > t
> > [ 4.200032] bone_capemgr bone_capemgr: slot #2: auto loading handled
> by U-Boo
> > t
> > [ 4.207386] bone_capemgr bone_capemgr: slot #3: auto loading handled
> by U-Boo
> > t
> > [ 6.389654] tda998x 0-0070: read edid timeout
> > rootfs: clean, 127622/217728 files, 744131/869376 blocks
> >
> > Debian GNU/Linux 9 beaglebone ttyS0
> >
> > BeagleBoard.org Debian Image 2017-08-31
> >
> > Support/FAQ: http://elinux.org/Beagleboard:BeagleBoneBlack_Debian
> >
> > default username:password is [debian:temppwd]
> >
> > beaglebone login: debian
> > Password:
> >
> > """"
> > For the same image, please also see my boot log on beaglebone.
> >
> > U-Boot 2016.03-00001-gd12d09f (Mar 17 2016 - 16:16:15 -0500), Build:
> jenkins-gi1
> >
> > Watchdog enabled
> > I2C: ready
> > DRAM: 512 MiB
> > Reset Source: Power-on reset has occurred.
> > MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1
> > Using default environment
> >
> > Net: <ethaddr> not set. Validating first E-fuse MAC
> > cpsw, usb_ether
> > Press SPACE to abort autoboot in 2 seconds
> > switch to partitions #0, OK
> > mmc0 is current device
> > Scanning mmc 0:1...
> > gpio: pin 56 (gpio 56) value is 0
> > gpio: pin 55 (gpio 55) value is 0
> > gpio: pin 54 (gpio 54) value is 0
> > gpio: pin 53 (gpio 53) value is 1
> > switch to partitions #0, OK
> > mmc0 is current device
> > gpio: pin 54 (gpio 54) value is 1
> > Checking for: /uEnv.txt ...
> > Checking for: /boot.scr ...
> > Checking for: /boot/boot.scr ...
> > Checking for: /boot/uEnv.txt ...
> > gpio: pin 55 (gpio 55) value is 1
> > 2080 bytes read in 40 ms (50.8 KiB/s)
> > Loaded environment from /boot/uEnv.txt
> > Checking if uname_r is set in /boot/uEnv.txt...
> > gpio: pin 56 (gpio 56) value is 1
> > Running uname_boot ...
> > loading /boot/vmlinuz-4.9.45-ti-r57 ...
> > 9464664 bytes read in 546 ms (16.5 MiB/s)
> > loading /boot/dtbs/4.9.45-ti-r57/am335x-boneblack.dtb ...
> > 58161 bytes read in 95 ms (597.7 KiB/s)
> > loading /boot/initrd.img-4.9.45-ti-r57 ...
> > 6395122 bytes read in 384 ms (15.9 MiB/s)
> > debug: [console=ttyO0,115200n8 root=/dev/mmcblk0p1 ro rootfstype=ext4
> rootwait .
> > debug: [bootz 0x82000000 0x88080000:6194f2 0x88000000] ...
> > Kernel image @ 0x82000000 [ 0x000000 - 0x906b58 ]
> > ## Flattened Device Tree blob at 88000000
> > Booting using the fdt blob at 0x88000000
> > Loading Ramdisk to 8f9e6000, end 8ffff4f2 ... OK
> > Loading Device Tree to 8f9d4000, end 8f9e5330 ... OK
> >
> > Starting kernel ...
> >
> > [ 0.000861] clocksource_probe: no matching clocksources found
> > [ 2.352397] wkup_m3_ipc 44e11324.wkup_m3_ipc: could not get rproc
> handle
> > [ 2.570055] omap_voltage_late_init: Voltage driver support not added
> > [ 2.577597] PM: Cannot get wkup_m3_ipc handle
> > [ 2.944617] bone_capemgr bone_capemgr: slot #0: No cape found
> > [ 2.975621] bone_capemgr bone_capemgr: slot #1: No cape found
> > [ 3.008278] bone_capemgr bone_capemgr: slot #2: No cape found
> > [ 3.040942] bone_capemgr bone_capemgr: slot #3: No cape found
> > rootfs: recovering journal
> > rootfs: Clearing orphaned inode 72631 (uid=0, gid=0, mode=040700,
> size=4096)
> > rootfs: Clearing orphaned inode 72632 (uid=0, gid=0, mode=041777,
> size=4096)
> > rootfs: clean, 126996/217728 files, 740103/869376 blocks
> > [ 18.675503] tilcdc 4830e000.lcdc: tilcdc_crtc_irq(0x00000020): FIFO
> underflow
> > [ 18.683167] tilcdc 4830e000.lcdc: tilcdc_crtc_irq(0x00000004): Sync
> lost
> > [ 18.690576] tilcdc 4830e000.lcdc: tilcdc_crtc_irq(0x00000004): Sync
> lost
> > [ 18.699830] tilcdc 4830e000.lcdc: tilcdc_crtc_irq(0x00000004): Sync
> lost
> > [ 18.700543] tilcdc 4830e000.lcdc: tilcdc_crtc_irq(0x00000004): Sync
> lost
> > [ 18.716500] tilcdc 4830e000.lcdc: tilcdc_crtc_irq(0x00000004): Sync
> lost
> > [ 18.717208] tilcdc 4830e000.lcdc: tilcdc_crtc_irq(0x00000004): Sync
> lost
> > [ 18.733165] tilcdc 4830e000.lcdc: tilcdc_crtc_irq(0x00000004): Sync
> lost
> > [ 18.733870] tilcdc 4830e000.lcdc: tilcdc_crtc_irq(0x00000004): Sync
> lost
> > [ 18.749842] tilcdc 4830e000.lcdc: tilcdc_crtc_irq(0x00000004): Sync
> lost
> > [ 18.750537] tilcdc 4830e000.lcdc: tilcdc_crtc_irq(0x00000004): Sync
> lost
> > [ 19.133859] tilcdc 4830e000.lcdc: tilcdc_crtc_irq(0x00000004): Sync
> lost flog
> >
> > Debian GNU/Linux 9 beaglebone ttyS0
> >
> > BeagleBoard.org Debian Image 2017-08-31
> >
> > Support/FAQ: http://elinux.org/Beagleboard:BeagleBoneBlack_Debian
> >
> > default username:password is [debian:temppwd]
> >
> > beaglebone login:
> > ********
> > The only difference I see in the log is U-boot bootloader being a
> different version in beaglebone. In beaglebone its not showing when it
> loads u-boot overlays.
> >
> > Also during Kernel loading I can see this tilcdc: "[ 18.683167] tilcdc
> 4830e000.lcdc: tilcdc_crtc_irq(0x00000004): Sync lost ", but I don't see
> this during boot on the clone board.
>
> This ^ was fixed in u-boot back in v2017.01-rc2:
>
>
> https://github.com/u-boot/u-boot/commit/8c17cbdf8a8023abdd0009af4dc9dbc0541b4a0f#diff-5ceb6e6d8a7e6348a75c69a248999eb3
>
>
> >
> > I would really appreciate if you can help me out with fixing the colors.
>
> Please retest with
>
> https://rcn-ee.net/rootfs/bb.org/testing/2018-12-30/stretch-lxqt/bone-debian-9.6-lxqt-armhf-2018-12-30-4gb.img.xz
>
>
> Using u-boot v2018.09 and v4.14.x based kernel that is shipped with the
> image..
>
> Regards,
>
> --
> Robert Nelson
> https://rcn-ee.com/
>
--
For more options, visit http://beagleboard.org/discuss
---
You received this message because you are subscribed to the Google Groups
"BeagleBoard" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to beagleboard+unsubscr...@googlegroups.com.
To view this discussion on the web visit
https://groups.google.com/d/msgid/beagleboard/55b3ff81-6dd7-41ff-b868-a70005e83b80%40googlegroups.com.
For more options, visit https://groups.google.com/d/optout.
