On Thu, Jan 3, 2019 at 3:14 PM <sam.abb...@gmail.com> wrote: > > Hi Robert, > > I tested debian-9.6 from the link you provided, and the colors on my clone > board are still inverted. > I tested the same image on beaglebone and the colors were correct. > > Please see my log below for the clone: > > U-Boot 2018.09-00002-gd5b4c4b656 (Oct 19 2018 - 14:16:02 -0500), Build: > jenkins- > github_Bootloader-Builder-84 > > CPU : AM335X-GP rev 2.1 > I2C: ready > DRAM: 512 MiB > No match for driver 'omap_hsmmc' > No match for driver 'omap_hsmmc' > Some drivers were not found > Reset Source: Global warm SW reset has occurred. > Reset Source: Power-on reset has occurred. > RTC 32KCLK Source: External. > MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 > Loading Environment from EXT4... ** File not found /boot/uboot.env ** > > ** Unable to read "/boot/uboot.env" from mmc0:1 ** > Board: BeagleBone Black > <ethaddr> not set. Validating first E-fuse MAC > BeagleBone Black: > Timed out in wait_for_event: status=0000 > Check if pads/pull-ups of bus are properly configured > BeagleBone: cape eeprom: i2c_probe: 0x54: > Timed out in wait_for_event: status=0000 > Check if pads/pull-ups of bus are properly configured > BeagleBone: cape eeprom: i2c_probe: 0x55: > Timed out in wait_for_event: status=0000 > Check if pads/pull-ups of bus are properly configured > BeagleBone: cape eeprom: i2c_probe: 0x56: > Timed out in wait_for_event: status=0000 > Check if pads/pull-ups of bus are properly configured > BeagleBone: cape eeprom: i2c_probe: 0x57: > Net: eth0: MII MODE > cpsw, usb_ether > Press SPACE to abort autoboot in 2 seconds > board_name=[A335BNLT] ... > board_rev=[000C] ... > switch to partitions #0, OK > mmc0 is current device > SD/MMC found on device 0 > switch to partitions #0, OK > mmc0 is current device > Scanning mmc 0:1... > gpio: pin 56 (gpio 56) value is 0 > gpio: pin 55 (gpio 55) value is 0 > gpio: pin 54 (gpio 54) value is 0 > gpio: pin 53 (gpio 53) value is 1 > switch to partitions #0, OK > mmc0 is current device > gpio: pin 54 (gpio 54) value is 1 > Checking for: /uEnv.txt ... > Checking for: /boot.scr ... > Checking for: /boot/boot.scr ... > Checking for: /boot/uEnv.txt ... > gpio: pin 55 (gpio 55) value is 1 > 2117 bytes read in 19 ms (108.4 KiB/s) > Loaded environment from /boot/uEnv.txt > debug: [dtb=am335x-boneblack.dtb] ... > Using: dtb=am335x-boneblack.dtb ... > Checking if uname_r is set in /boot/uEnv.txt... > gpio: pin 56 (gpio 56) value is 1 > Running uname_boot ... > loading /boot/vmlinuz-4.14.79-ti-r86 ... > 9712128 bytes read in 632 ms (14.7 MiB/s) > debug: [enable_uboot_overlays=1] ... > debug: [enable_uboot_cape_universal=1] ... > debug: [uboot_base_dtb_univ=am335x-boneblack-uboot-univ.dtb] ... > uboot_overlays: [uboot_base_dtb=am335x-boneblack-uboot-univ.dtb] ... > uboot_overlays: Switching too: dtb=am335x-boneblack-uboot-univ.dtb ... > loading /boot/dtbs/4.14.79-ti-r86/am335x-boneblack-uboot-univ.dtb ... > 161719 bytes read in 57 ms (2.7 MiB/s) > uboot_overlays: [fdt_buffer=0x60000] ... > uboot_overlays: loading /lib/firmware/BB-BONE-eMMC1-01-00A0.dtbo ... > 1440 bytes read in 55 ms (25.4 KiB/s) > uboot_overlays: loading /lib/firmware/BB-HDMI-TDA998x-00A0.dtbo ... > 4896 bytes read in 76 ms (62.5 KiB/s) > uboot_overlays: loading /lib/firmware/BB-ADC-00A0.dtbo ... > 711 bytes read in 183 ms (2.9 KiB/s) > uboot_overlays: loading /lib/firmware/AM335X-PRU-RPROC-4-14-TI-00A0.dtbo ... > 3513 bytes read in 160 ms (20.5 KiB/s) > loading /boot/initrd.img-4.14.79-ti-r86 ... > 4636329 bytes read in 306 ms (14.4 MiB/s) > debug: [console=ttyO0,115200n8 bone_capemgr.uboot_capemgr_enabled=1 > root=/dev/mm > cblk0p1 ro rootfstype=ext4 rootwait coherent_pool=1M net.ifnames=0 quiet > video=H > DMI-A-1:1024x768@60e] ... > debug: [bootz 0x82000000 0x88080000:46bea9 88000000] ... > ## Flattened Device Tree blob at 88000000 > Booting using the fdt blob at 0x88000000 > Loading Ramdisk to 8fb94000, end 8ffffea9 ... OK > reserving fdt memory region: addr=88000000 size=89000 > Loading Device Tree to 8fb08000, end 8fb93fff ... OK > > Starting kernel ... > > [ 0.002388] timer_probe: no matching timers found > [ 1.081030] wkup_m3_ipc 44e11324.wkup_m3_ipc: could not get rproc handle > [ 1.378727] omap_voltage_late_init: Voltage driver support not added > [ 1.386104] PM: Cannot get wkup_m3_ipc handle > [ 1.851328] musb-hdrc musb-hdrc.1: VBUS_ERROR in a_wait_vrise (80, > <SessEnd), > retry #3, port1 0008010c > [ 2.757564] tda998x 0-0070: read edid timeout > [ 2.856904] hdmi-audio-codec hdmi-audio-codec.0.auto: ASoC: no source > widget > found for Playback > [ 2.865915] hdmi-audio-codec hdmi-audio-codec.0.auto: ASoC: Failed to add > rou > te Playback -> direct -> TX > [ 5.037791] tda998x 0-0070: read edid timeout > > Debian GNU/Linux 9 beaglebone ttyS0 > > BeagleBoard.org Debian Image 2018-12-30 > > Support/FAQ: http://elinux.org/Beagleboard:BeagleBoneBlack_Debian > > default username:password is [debian:temppwd] > > beaglebone login: > > ****** > > I really don't understand why its causing this color invert on the clone > board. > Any suggestions would be greatly appreciated.
Smells like the clone board isn't a 100% clone... Regards, -- Robert Nelson https://rcn-ee.com/ -- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to beagleboard+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/beagleboard/CAOCHtYh6bfnVr9Mjpdi33o1D-1STwMQLUMJ869Fv2fGVXyNDyA%40mail.gmail.com. For more options, visit https://groups.google.com/d/optout.
