You can use putty Em sáb., 5 de dez. de 2020 às 15:27, John Bacas <[email protected]> escreveu:
> As I said I'm a newbie > Luckily I have an FTDI cable , but what software should I use as a console > to read data from PB? I have Windows 10. > > Actually, when I plug PB to my PC it makes the sound of connecting and a > COM port appears in the Device Manager, but then another sound of > disconnecting. This thing repeats for 10 times and finnaly the COM port > disappears. > Thnx > Στις Σάββατο, 5 Δεκεμβρίου 2020 στις 7:12:18 μ.μ. UTC+2, ο χρήστης > [email protected] έγραψε: > >> If the LEDs are not blinking as expected, that does not sound good. If >> you have a FTDI cable, you could try to connect it to the PB as shown on >> the following page to see if you get any messages related to the issue: >> >> https://beagleboard.org/p/ken-shirriff/hands-on-with-the-pocketbeagle-a-25-linux-computer-606c66 >> >> I'm assuming you are not seeing a COM port active for the PB on your >> Windows PC, correct? >> >> Cheers, >> >> Jon >> >> On Sat, Dec 5, 2020 at 5:32 AM John Bacas <[email protected]> wrote: >> >>> I have used "*AM3358 Debian 10.3 2020-04-06 4GB SD IoT*" image file >>> and I used "*rufus 3.1*" to flash the image. >>> As I said, all 4 leds lighted up sequencially and after a while the >>> user0 led flashed like a heartbeat and user1 led kept flashing randomly. >>> That is normal as I have read, but still in my computer no device was >>> detected. >>> After some unplugging and plugging, I used "*Etcher*" to flash the >>> image. >>> Then I flashed some older images like "*Debian 9.9 2019-08-03 4GB SD >>> IoT*" and "*AM3358 Debian 10.0 2019-07-07 4GB SD IoT*" with "Etcher" >>> too. >>> I have tried a different sd card but nothing changed. >>> Yesterday when I plugged Beagle in the usb port, an "RNDIS...." message >>> appeard but not any connection and only user0 led stays constantly lit. >>> User0 led is about kernel, so is there any damage inside the chip? >>> >>> Στις Σάββατο, 5 Δεκεμβρίου 2020 στις 2:39:17 π.μ. UTC+2, ο χρήστης >>> [email protected] έγραψε: >>> >>>> What image did you flash to the uSD card? >>>> What tool did you use to flash the image to the uSD card? >>>> >>>> Cheers, >>>> >>>> Jon >>>> >>>> On Fri, Dec 4, 2020 at 12:36 PM John Bacas <[email protected]> wrote: >>>> >>>>> Hi, I'm a newbie with beagle board and I have a problem with my pocket >>>>> one. >>>>> I did all according to the quick start guide. >>>>> When i plugged it to my pc all 4 leds lighted up sequentially but I >>>>> was waiting for 1 minute and nothing happened. There wasn't any new drive >>>>> appearing in my windows explorer. >>>>> Unplugged it without turning it off and plugged it again. Same >>>>> bahavior. >>>>> After a lot o sd card flashing and tries to boot, things got worse. >>>>> Now when i plug the board only user0 led lights up and stays open. >>>>> Have I damaged it ? How can I check if it has damage? >>>>> Can I fix it ? >>>>> >>>>> Thanks >>>>> >>>>> -- >>>>> For more options, visit http://beagleboard.org/discuss >>>>> --- >>>>> You received this message because you are subscribed to the Google >>>>> Groups "BeagleBoard" group. >>>>> To unsubscribe from this group and stop receiving emails from it, send >>>>> an email to [email protected]. >>>>> To view this discussion on the web visit >>>>> https://groups.google.com/d/msgid/beagleboard/744326f5-f51d-4c41-9771-da5272edb840n%40googlegroups.com >>>>> <https://groups.google.com/d/msgid/beagleboard/744326f5-f51d-4c41-9771-da5272edb840n%40googlegroups.com?utm_medium=email&utm_source=footer> >>>>> . >>>>> >>>> -- >>> For more options, visit http://beagleboard.org/discuss >>> --- >>> You received this message because you are subscribed to the Google >>> Groups "BeagleBoard" group. >>> To unsubscribe from this group and stop receiving emails from it, send >>> an email to [email protected]. >>> >> To view this discussion on the web visit >>> https://groups.google.com/d/msgid/beagleboard/688b764d-8c22-4429-97d1-39356414818dn%40googlegroups.com >>> <https://groups.google.com/d/msgid/beagleboard/688b764d-8c22-4429-97d1-39356414818dn%40googlegroups.com?utm_medium=email&utm_source=footer> >>> . >>> >> -- > For more options, visit http://beagleboard.org/discuss > --- > You received this message because you are subscribed to the Google Groups > "BeagleBoard" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > To view this discussion on the web visit > https://groups.google.com/d/msgid/beagleboard/b42ca426-265c-4c80-b56b-4fd6fb1bdd4an%40googlegroups.com > <https://groups.google.com/d/msgid/beagleboard/b42ca426-265c-4c80-b56b-4fd6fb1bdd4an%40googlegroups.com?utm_medium=email&utm_source=footer> > . > -- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion on the web visit https://groups.google.com/d/msgid/beagleboard/CAB6xwCqJJ9ttVdKZtKGPRJayvdbbV-CTmX1GP%3Dh3HMH95hPy0A%40mail.gmail.com.
