Also other variants, bin h bin s cc ok cc cancel bin s bin z
bin h cc ok bin s cc cancel bin s bin z bin h bin s3 cc ok bin s2 cc cancel bin s1 bin z Ср, 18 дек 2013, bill lam писал(а): > wiki said wd'set id wh ..' not wd'wh ..', > > Resizing a form depends on window manager, different desktops > may behave differently, Qt can only provide hints to wm and > cannot override it. > > Not sure what you intended for the bin s, your code runs like > this > > bin h > bin s > cc ok > cc cancel > bin z > > alternatively, you may try > > bin h > cc ok > cc cancel > bin s > bin z > > or > > bin h > cc ok > bin s > cc cancel > bin z > > BTW the first line > (;:'wdbase z') copath 'base' > is redundant. > > Вт, 17 дек 2013, Don Guinn писал(а): > > T tried several numbers and letters. No change in effect. I used a short > > script from WIKI Guides/J8 Standalone. I made a few minor changes. It > > follows: > > > > (;:'wdbase z') copath 'base' > > > > > > GETURL=: 0 : 0 > > > > pc geturl escclose dialog ;pn "Retrieve URL"; > > > > bin vh; > > > > minwh 40 22;cc urlsrc static right;cn "URL"; > > > > minwh 400 24;cc src edit; set src text http://; > > > > bin z; > > > > bin h s ; > > > > cc ok button;cn "&OK"; > > > > cc cancel button;cn "&Cancel"; > > > > pcenter; > > > > ) > > > > > > test=: 3 : 0 > > > > wd GETURL > > > > wd'pshow' > > > > ) > > > > > > geturl_cancel_button=: 3 : 0 > > > > wd 'pclose' > > > > ) > > > > > > test '' > > > > > > I made the form to allow resizing to better see the actions. Added a cancel > > to make it easy to get rid of. Should have been able to use ESC but for > > some reason it didn't work. I had to change the "wh" to "minwh" as I got > > "wh : command not found: wd". I tried the form in both W7 and UBUNTU. Got > > same error. Guides/JqtChildClasses lists both "wh" and "minwh" as valid. > > > > > > In both W8 and UBUNTU if I had the "s" on the last bin the two buttons > > tracked with the right side of the form and their size remained constant as > > I resized the form. The size of the edit token stretched horizontally with > > the form size. On W8 the form size would not resize smaller than the > > minimum size of the edit token. But on UBUNTU the form size continued to > > shrink and the right side of the edit token was cut off. I could even > > shrink it vertically until the tokens were almost invisible. > > > > > > I tried all sorts of number and letters which should be invalid and no > > change in the way the form worked. Even tried a question mark. Never an > > error. If the "s" was there the buttons moved to the right with the form > > and their size was unchanged. If it was gone the buttons stretched > > horizontally to fill the width of the form and shrank and stretched > > horizontally as the size of the form changed. > > > > > > From the About box. > > > > > > Engine j701/2011-01-10/11:25 > > > > Library: 8.01.016 > > > > Qt IDE: 1.0.21/4.8.5 > > > > Platform: Win 64 > > > > > > On Sun, Dec 15, 2013 at 5:52 PM, bill lam <[email protected]> wrote: > > > > > that refers to the remaining spaces, try place 2 stretch bin with > > > different > > > numbers to see if the factor can take effect. untested. > > > On Dec 16, 2013 7:30 AM, "Don Guinn" <[email protected]> wrote: > > > > > > > I have been waiting for a better explanation of the s parameter for wd > > > bin > > > > "s". "s" can be followed by a number which is supposed to be the stretch > > > > factor. I haven't found any good description yet. Any number put there > > > > always gives the same result, the tokens are right justified if s is > > > > present and stretched to fill if s is not present. > > > > > > > > Seems like there should be ways to left justify, center, right justify > > > and > > > > stretch to fill. And possibly have some tokens left justified and others > > > > right justified. > > > > ---------------------------------------------------------------------- > > > > For information about J forums see http://www.jsoftware.com/forums.htm > > > > > > > ---------------------------------------------------------------------- > > > For information about J forums see http://www.jsoftware.com/forums.htm > > > > > ---------------------------------------------------------------------- > > For information about J forums see http://www.jsoftware.com/forums.htm > > -- > regards, > ==================================================== > GPG key 1024D/4434BAB3 2008-08-24 > gpg --keyserver subkeys.pgp.net --recv-keys 4434BAB3 > gpg --keyserver subkeys.pgp.net --armor --export 4434BAB3 -- regards, ==================================================== GPG key 1024D/4434BAB3 2008-08-24 gpg --keyserver subkeys.pgp.net --recv-keys 4434BAB3 gpg --keyserver subkeys.pgp.net --armor --export 4434BAB3 ---------------------------------------------------------------------- For information about J forums see http://www.jsoftware.com/forums.htm
