Bob, I have the Grizzly G1022SM I believe that the SM represents standard model. I am not sure where you live but Grizzly has two showrooms in the U.S. One in the west and the other here in Pa. about 1 - 1/2 hour drive. The showroom is unbelievable. I think over 10,000 items on display. I have the Grizzly table saw, 2HP dust collector and a 12 speed drill press. When I needed to replace my bench sander I looked at the Grizzly but ended up with a Ryobi. It was about the same price, didn't require assembly and had a better review. I am very pleased with the three big tools that I purchased from Grizzly. I would like a more powerful dust collector. the 2HP is ok but nothing like a friend's 10 HP. I can not scale this one down to 1" there is no suction where as my friends is fantastic when hooked up to his hand held router. His shop has no noticeable dust. Although his is for a business. ----- Original Message ----- From: "Bob Kennedy" <[EMAIL PROTECTED]> To: <[email protected]> Sent: Sunday, December 16, 2007 3:34 PM Subject: Re: [BlindHandyMan] table saw safety accessories
Which one did you get? I was looking at 2 Grizzly saws but there wasn't anyone in my area they could recommend to let me look at the saw. ----- Original Message ----- From: Lenny McHugh To: [email protected] Sent: Sunday, December 16, 2007 3:18 PM Subject: Re: [BlindHandyMan] table saw safety accessories Hi Glenn, I have a Grizzly and really like it especially since I upgraded the belt. I installed the power twist link belt and the saw now has no vibration. Hard to believe that a belt can make the difference. With this new belt a nickel will stand on end while the saw is running and my cuts seem to be improved. The belt was $30 but looking back it is really worth it. ----- Original Message ----- From: "GLENN PERMAR" <[EMAIL PROTECTED]> To: <[email protected]> Sent: Sunday, December 16, 2007 3:01 PM Subject: Re: [BlindHandyMan] table saw safety accessories Hi guys, I have always kept the guard on my table saw mainly because of the anti-kickback pieces on either side. About the only problems I have had with the guards is if it gets off center of the blade and then whatever you are cutting hits the support piece of the guard instead of the cut slot going over it. I was also interested in what kind of table saws any of you have bought lately that seem to be good. I am in the market for a new one now. I have a Craftsman now and have been looking at a new Jet that Woodcraft has. It has a nice fence and a decent miter gauge. It also has a one and three quarter horse power motor. Thanks for any input. Glenn, ----- Original Message ----- From: John Schwery To: [email protected] Sent: Sunday, December 16, 2007 10:22 AM Subject: Re: [BlindHandyMan] table saw safety accessories Dale's question was about cutting a board that is bigger than the table. I suppose one could clamp a board under the board to be cut, sliding the clamped board along the table. earlier, Bob Kennedy, wrote: >A few years back I went to the Woodworking Show in Charlotte, NC. >One of the brothers that own one of the many companies at the show >was there demonstrating his system for safety and accuracy. The >system is called the Grip-Tite system. Basically it is a long piece >of steel about 4 inches tall and bent at 90 degrees at the top. The >bend is only to add strength to the steel, it isn't important otherwise. > >The steel plate has holes counter sunk into it along the length and >you screw it to a piece of wood which becomes the back. The wood is >then held against the original fence of the table saw. So if the >picture isn't clear mentally at this point, you have a 4 inch tall >fence now attached to your original fence. > >The part that makes this special is the clamps that hold the wood >down. They are awesome magnets inside of a lexan housing and they >stick extremely well to this fence face. On the side of the magnet >housing is a wheel that rolls as the wood passes under it. This >keeps the wood pressed firmly against the surface of the saw bed and >won't let a board raise up off the blade as the leverage increases >at the outfeed side. > >There are 2 magnets, one for the front and one at the back of the >fence. Since I bought mine, they have come out with some new >accessories that I haven't checked into yet but since I just got a >new table saw myself, I will need to figure out a better way to fit >this. I have the Biesemeyer fence on the saw and can't attach the >old system to the new fence. They do however, make clamps to fit the >bigger fences. > >If you ever get near a Woodcraft store or something similar, be sure >to have them show you how this works. I am a hard head when it comes >to blade guards and leave mine off all the time. As dirty Harry >said, "A man's got to know his limitations." And I do. So I know how >far I need to keep my hands from the blade and don't challenge the >blade in any way. What is so neat about these magnets is once they >are in place on the fence face, there is a handle on the housing >that will also serve as a blade guard. If you are having a brain >cramp while feeding wood through the blade, your hand will run into >the magnet first. Believe me, it is big enough you won't just pass >over it and hit the blade unless you intend to. I don't have 1 >handy, but estimating I would say the magnet housing is about 3 >inches wide and about 6 inches end to end. The handle fits my hand >and comes off the top which is probably an inch and a half thick. So >at the end of the handle it is roughly 5 or 6 inches tall. Tallisn't >the right word since the bottom sticks to the fence and that makes >the handle point to the side at that point... I have never had a >kick back when I used the magnets on a cut. Once you stick one to >the fence, you are in for a surprise getting it loose. They have a >lever on the tail that works a cam to help break some of the >magnetic force. They will snap to the fence from about an inch away >so you learn quickly where not to have your fingers. > >Obviously I was impressed with the whole Grip-Tite system. But I >think what sold me completely was the guy selling it. He puts on a >show so you can see how well it works. At the show I watched the guy >push a 2 by 4 through the blade and after it was about half way >along the cut, he gave the wood a push sideways and the blade was >binding and screaming. The board never kicked back at him. It was a >demonstration of course he knows better than to cut like that. After >everyone was through talking to him I introduced myself and asked if >he would show it to me. He let me run my hands all over the saw and >then he asked if I wanted to make a cut. I'd have bought the tool at >that time just because of his attitude. What he wanted me to know >was that I couldn't get my hands near the blade unless I wanted to. >He said once you run into the handle of the magnet, you know the >blade is about 4 inches beyond and that is your stopping point. He >knew I was a total and it didn't scare him at all for me to use the >saw And you know how the courts would nail him if I would have >gotten hurt. You can Google >Grip-Tite and read some of the reviews on it. They sell for around >$129 US, and they are worth every penny. > >----- Original Message ----- >From: Dale Alton >To: <mailto:blindhandyman%40yahoogroups.com>[email protected] >Sent: Saturday, December 15, 2007 11:29 PM >Subject: [BlindHandyMan] tips, tricks, and knowledge > >Well I did it. I bought both. I am still hesitant with the table saw >but am excited to use it. I want to be as careful as possible and >want the subject on using a table saw. I am primarily concerned with >a piece larger than the table. How is a person suppose to run say a >8 foot piece of 1" x ^' through the table by himself? I like my 10 digits. >Thanx, >Dale > >[Non-text portions of this message have been removed] > >[Non-text portions of this message have been removed] > > > >No virus found in this incoming message. >Checked by AVG Free Edition. >Version: 7.5.503 / Virus Database: 269.17.2/1185 - Release Date: >12/15/2007 12:00 PM John ---------- No virus found in this outgoing message. Checked by AVG Free Edition. Version: 7.5.503 / Virus Database: 269.17.4/1187 - Release Date: 12/16/2007 11:36 AM [Non-text portions of this message have been removed] [Non-text portions of this message have been removed] To listen to the show archives go to link http://acbradio.org/handyman.html or ftp://ftp.acbradio.org/acbradio-archives/handyman/ The Pod Cast address for the Blind Handy Man Show is. http://www.acbradio.org/news/xml/podcast.php?pgm=saturday Visit The Blind Handy Man Files Page To Review Contributions From Various List Members At The Following address: http://www.jaws-users.com/handyman/ Visit the archives page at the following address http://www.mail-archive.com/[email protected]/ If you would like to join the Blind Computing list, then visit the following address for more information: http://jaws-users.com/mailman/listinfo/blind-computing_jaws-users.com For a complete list of email commands pertaining to the Blind Handy Man list just send a blank message to: [EMAIL PROTECTED] Yahoo! Groups Links [Non-text portions of this message have been removed] To listen to the show archives go to link http://acbradio.org/handyman.html or ftp://ftp.acbradio.org/acbradio-archives/handyman/ The Pod Cast address for the Blind Handy Man Show is. http://www.acbradio.org/news/xml/podcast.php?pgm=saturday Visit The Blind Handy Man Files Page To Review Contributions From Various List Members At The Following address: http://www.jaws-users.com/handyman/ Visit the archives page at the following address http://www.mail-archive.com/[email protected]/ If you would like to join the Blind Computing list, then visit the following address for more information: http://jaws-users.com/mailman/listinfo/blind-computing_jaws-users.com For a complete list of email commands pertaining to the Blind Handy Man list just send a blank message to: [EMAIL PROTECTED] Yahoo! Groups Links
