Dale, I have used various scrapers in furniture stripping. The article says well what you need to know. It is more a matter of doing to get the hang of it. . Sometimes mine would sharpen better than other times , but was likely I didn't remove the old burr before resharpening. Sometime I would lay the scrapper flat on the table of my belt sander and run it across to sand the edge flat. this would leave a burr on the down side and not the top. That wasn't a problem since at that time I was just removing finish. When the finish was all gone and scraping the wood then the more careful attention with flat sides and using the burnisher to curl the edge is necessary for good wood smoothing. Nothing new from me, but as we both know attention to detail gives the best results. Ron ----- Original Message ----- From: Dale Leavens To: [email protected] Cc: [EMAIL PROTECTED] Sent: Tuesday, May 27, 2008 11:11 PM Subject: [BlindHandyMan] Using a card scraper.
Sorry folks, I found a couple of sites which describe the process pretty well. I will include one of what I found below in case it is of interest to some others of the list. Using and burnishing a cabinet scraper Sharpening and using a cabinet scraper using cabinet scraper One of the more satisfying hand tools to use is a cabinet scraper. Its satisfying to use because in many ways, allows me to do away with sanding, and at the same time produces a very precise and even finish. Its a tool that's indispensable when leveling a hardwood table top. The trick to using a cabinet scraper is its preparation. The scraper loses most of its edge after just 10 minutes of use, so burnishing (sharpening) the scraper is an essential part of it use. In fact, a new scraper doesn't even come with a usable edge out of the box, so I'll start with how to burnish the scraper to have a nice burr on it. To form a burr on the scraper, a square edge is needed. Unless the scraper is brand new, the first step is to file off any remains of the old, worn burr. Start by filing the sides of the scraper. This only takes a few strokes. Wether the old burr is completely gone can easily be checked by grabbing the edge of the scraper and pulling the fingers up. If there's nothing to catch, the old burr is gone. The next step is to flatten the top edge. From making the previous burr, the top surface will be a little bit round, which makes it more difficult to form a new burr. A few strokes with a file across the top takes care of this. I usually file the top until I can once again feel a slight burr forming on the sides from the filing. Again, I test this by pulling my fingers up against the edge. hand file Some people recommend smoothing the scraper edges with a stone before forming a new burr. No doubt, this would make a small improvement in the quality of the final burr, but I find that to be unnecessary trouble. I use a very fine file, with teeth formed only on a diagonal (no crosshatch), which I think produces a smoother finish than a crosshatched file normally would. burnishing geometry Scraper edge macro photo The next step is where the magic comes in. Using a burnishing tool made of very hard high carbon steel, a 'Burr' is created along the edges of the scraper as shown at left. This is done by pushing the burnishing tool very firmly onto the scraper, and pushing it along the edge of the scraper. This causes the corners of the scraper to deform and form a sort of hook shaped burr. The burr is very small, and barely visible. I tried to photograph it (see right), but its really hard to see. In fact, the burr itself is only about 0.05 mm wide, I measured this with a dial caliper. Successful burnishing does require that the burnishing tool be harder than the scraper, and seeing that the scraper is already made of fairly hard steel, the burnihser needs to be very hard. I use a Veritas burnisher, from Lee Valley Tools. Some people suggest using the shaft of a screwdriver. But form personal experience, I can assure you, this does not work. I also tried a sharpening steel from a houseware store, but this also wasn't quite hard enough. Before I got my veritas burnisher, I used a file with a round-ish safe edge, so that I could use the round side of the file without having any of the file's cutting surface touch the scraper. burnishing tool Using the cabinet scraper palm plane Once the scraper is all sharpened, its time to tackle the work piece. But a scraper is very slow at removing material. Still faster than sandpaper, but very slow. So if I have any uneven ness on a surface that is more than a fraction of a millimeter, I level these first with a small hand plane. Much quicker than trying to remove a lot of material with a scraper, although it does risk gouging the surface in spots where the grain pulls the plane into the wood. In use, the scraper is held at a relatively low angle to the wood and pulled over the surface, so that shavings form on the lower edge of the scraper against the wood. This angle allows the hook of the burr to engage the wood. the shape of the burr and scraper only allow it to take off about 0.02 millimeters of material at a time at most. Depending on where I'm working it, I use it one handled, or two handed. The two hand hold allows the scraper to be bent slightly, so that if the wood dips slightly in an area, the scraper can still be pressed into it. The two hand hold also gives a bit more power. wood shavings from scraper Like sanding, using a scraper needs a lot of elbow grease, so if I'm doing a table top, I usually don't do it all at once. Its also quite normal for the scraper to get quite hot to the touch when working it. For a table top of about 1 square meter area, I end up resharpening the scraper at least twice before its done. gleaming scraped finish A belt sander would of course do the job faster, but excessive sanding always results in a very imprecise wavy looking surface that just isn't appealing to me. A scraper is much better at evening out discontinuities in the surface, and also produces a finish smoother than sandpaper. In fact, the surface tends to actually have a bit of a shine to it. The image at left is after scraping, but before varnishing. The cabinet scrapers I use are 0.8 mm thick, and I got them from Lee Valley tools. Other materials can also be used, although stainless steel would probably be too brittle for the job. I have used pieces of knives from a paper cutter, although these provide only one edge for sharpening. Other than being too stiff to flex into uneven spots, the cutter blades worked just as well. [Non-text portions of this message have been removed] [Non-text portions of this message have been removed]
