Jim, regardless of your problem or solution, I loved reading your post! Part of me hopes you fail to fix it, so I can look forward to more comedy!
I’ve used both white and yellow teflon tape and never had a leak with either. As you said, clean joint, follow mfr recommendations on number of wraps, and forget about it. The p-tex is fine too but unnecessarily complex. The Expobar stuff works great, but you have about 1.69 nanoseconds to get the part turned to the right orientation before it sets up. 0.69 nanoseconds if the machine/part is warm/hot when you’re doing it. Best of luck, and wishing you continued donkey-blinding espresso in the near future. b > On Dec 1, 2020, at 15:40, Joseph Helminiak <[email protected]> > wrote: > > I replaced mine and just used white teflon tape. > > Joseph (Joe) Helminiak > (314) 556-4488 > > > On Mon, Nov 30, 2020 at 8:01 PM James Mitchell <[email protected] > <mailto:[email protected]>> wrote: > Things aren't going so well with our Brewtus II - Katherine was making our > morning shots, and as she turned towards the sink with its drip tray: "There > was this 'Swizz. Pop., BANG!' and all the kitchen lights went out." > > No, it wasn't our neighbors playing with an RPG - it was the blessed brew > boiler heating element going South and taking out a GFCI socket in a fairly > spectacular fashion: > > https://drive.google.com/file/d/1C0w2AIcqeqiuG6vqQHi5FW9MmCvCIcL7/view?usp=sharing > > <https://drive.google.com/file/d/1C0w2AIcqeqiuG6vqQHi5FW9MmCvCIcL7/view?usp=sharing> > > It looks like there was water intrusion near the element's base, and when it > flashed to steam it ripped the element apart. The loud bang was a very > marginal GFCI socket failing to deal with a dead short on a twenty amp > circuit. > > The circuit is now on a 15 amp breaker, there's a medical-grade dual socket > rated for 15 amp continuous service, and a new boiler element is due this > week from WLL. > > No one appears to have stock on the Expobar-specific thread sealant - Stefano > recommends an italian sealant which looks very good - which I'd buy, but USPS > from Oregon to North Carolina is pretty glacial at the best of times, and > we're getting impatient. > > The local HVAC folks who keep our 75 year old steam heat system working swear > by Permatex 56521: "It applies easily, sets up quickly, remains flexible, and > in a clean joint - never, ever leaks." > > 56521 has no NSF rating, and its MDS lists ethanol as a primary carrier, with > 1% Methanol as an additional carrier. While folks have maintained that K's > coffee: "Could stun a horse & blind a donkey..." I've no desire to actualize > their experience, and will use the sealant only on the the upper threads with > 4-5 wraps of teflon tape on the lower threads to isolate it from the brew > water. > > There appears to be good water flow through the E61, with no portafilter the > Elka pump will fill an 8 oz glass in less than 15 seconds - I'll pull the > water level probe, clean and inspect it for continuity and scale, to > eliminate it causing an underfill condition. > > Much past this point, my troubleshooting gets fairly mystical, since the > volume of water flow through the grouphead belies issues with the parker > valve or Elka pump, my most popular theories tend to include demons, Maxwell > Houses, and extremely bad JuJu. > > Cheers & Thanks > Jim > > > > -- > You received this message because you are subscribed to the Google Groups > "Brewtus" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected] > <mailto:[email protected]>. > To view this discussion on the web visit > https://groups.google.com/d/msgid/brewtus/2e070887-e040-46a8-a389-a475b2f26cedn%40googlegroups.com > > <https://groups.google.com/d/msgid/brewtus/2e070887-e040-46a8-a389-a475b2f26cedn%40googlegroups.com?utm_medium=email&utm_source=footer>. > > -- > You received this message because you are subscribed to the Google Groups > "Brewtus" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected] > <mailto:[email protected]>. > To view this discussion on the web visit > https://groups.google.com/d/msgid/brewtus/CAGs_PrOB%2B4nC1GOdxpQKMaTsyXZLRiEJ4T2mwh1uGd%3DQW8n_xw%40mail.gmail.com > > <https://groups.google.com/d/msgid/brewtus/CAGs_PrOB%2B4nC1GOdxpQKMaTsyXZLRiEJ4T2mwh1uGd%3DQW8n_xw%40mail.gmail.com?utm_medium=email&utm_source=footer>. -- You received this message because you are subscribed to the Google Groups "Brewtus" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion on the web visit https://groups.google.com/d/msgid/brewtus/F10BB356-8379-415F-976B-775A51555319%40me.com.
