On Wed, Jul 14, 2010 at 12:38:05PM -0400, Ted Unangst wrote:
> On Wed, Jul 14, 2010 at 12:29 PM, Christopher Linn <[email protected]> wrote:
> > kernel boot messages produce about one screen of output before
> > crashing on uvm_fault and halting. dmesg and other output was
> > generated by sendbug on the installed snapshot, here is a
> > transcription of the screen when booting RAMDISK_CD #12:
>
> > acpi0 at bios0: rev 0uvm_fault(0xd07db798, 0x0, 0, 1) -> e
> > fatal page fault (6) in supervisor mode
> > trap type 6 code 0 eip d04d7c41 cs 8 eflags 10092 cr2 30 cpl 0
> > panic: trap type 6, code=0, pc=d04d7c41
>
> What happens if you disable acpi?
OpenBSD 4.7-current (RAMDISK_CD) #12: Tue Jul 13 23:53:07 MDT 2010
[email protected]:/usr/src/sys/arch/i386/compile/RAMDISK_CD
cpu0: Intel(R) Pentium(R) 4 CPU 1400MHz ("GenuineIntel" 686-class) 1.40 GHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM
real mem = 1073049600 (1023MB)
avail mem = 1048563712 (999MB)
User Kernel Config
UKC> disable acpi
256 acpi0 disabled
UKC> quit
Continuing...
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 10/08/01, BIOS32 rev. 0 @ 0xfda74, SMBIOS
rev. 2.3 @ 0xf0fd0 (63 entries)
bios0: vendor Intel Corp. version "GB85010A.86A.0078.P18.0110081719" date
10/08/2001
bios0: Intel Corporation D850GB
acpi at bios0 function 0x0 not configured
pcibios0 at bios0: rev 2.1 @ 0xf0000/0x10000
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xf2f30/208 (11 entries)
pcibios0: PCI Interrupt Router at 000:31:0 ("Intel 82371FB ISA" rev 0x00)
pcibios0: PCI bus #2 is the last bus
bios0: ROM list: 0xc0000/0xf800 0xcf800/0x1000 0xd0800/0x1000 0xd1800/0x5800
cpu0 at mainbus0: (uniprocessor)
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 0 function 0 "Intel 82850 Host" rev 0x02
ppb0 at pci0 dev 1 function 0 "Intel 82850/82860 AGP" rev 0x02
pci1 at ppb0 bus 1
vga1 at pci1 dev 0 function 0 "NVIDIA GeForce4 MX 4000" rev 0xa4
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
ppb1 at pci0 dev 30 function 0 "Intel 82801BA Hub-to-PCI" rev 0x02
pci2 at ppb1 bus 2
fxp0 at pci2 dev 8 function 0 "Intel 82562" rev 0x01, i82562: irq 11, address
00:03:47:68:50:ae
inphy0 at fxp0 phy 1: i82562EM 10/100 PHY, rev. 0
pciide0 at pci2 dev 10 function 0 "Promise PDC20269" rev 0x02: DMA, channel 0
configured to native-PCI, channel 1 configured to native-PCI
pciide0: using irq 9 for native-PCI interrupt
atapiscsi0 at pciide0 channel 0 drive 0
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <DVDRW, IDE1008, 0055> ATAPI 5/cdrom removable
atapiscsi1 at pciide0 channel 0 drive 1
scsibus1 at atapiscsi1: 2 targets
cd1 at scsibus1 targ 0 lun 0: <LG, CD-ROM CRD-8520B, 1.00> ATAPI 5/cdrom
removable
cd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 4
cd1(pciide0:0:1): using PIO mode 4, DMA mode 2
ahc0 at pci2 dev 11 function 0 "Adaptec AHA-2940AU" rev 0x01: irq 10
scsibus2 at ahc0: 8 targets, initiator 7
sd0 at scsibus2 targ 2 lun 0: <SEAGATE, ST3146807LW, 0006> SCSI3 0/direct fixed
sd0: 140014MB, 512 bytes/sec, 286749488 sec total
ohci0 at pci2 dev 12 function 0 "NEC USB" rev 0x41: irq 5, version 1.0
ohci1 at pci2 dev 12 function 1 "NEC USB" rev 0x41: irq 11, version 1.0
ehci0 at pci2 dev 12 function 2 "NEC USB" rev 0x02: irq 9
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "NEC EHCI root hub" rev 2.00/1.00 addr 1
"C-Media Electronics CMI8738/C3DX Audio" rev 0x10 at pci2 dev 13 function 0 not
configured
usb1 at ohci0: USB revision 1.0
uhub1 at usb1 "NEC OHCI root hub" rev 1.00/1.00 addr 1
usb2 at ohci1: USB revision 1.0
uhub2 at usb2 "NEC OHCI root hub" rev 1.00/1.00 addr 1
ichpcib0 at pci0 dev 31 function 0 "Intel 82801BA LPC" rev 0x02: 24-bit timer
at 3579545Hz
pciide1 at pci0 dev 31 function 1 "Intel 82801BA IDE" rev 0x02: DMA, channel 0
wired to compatibility, channel 1 wired to compatibility
wd0 at pciide1 channel 0 drive 0: <ST340823A>
wd0: 16-sector PIO, LBA, 38166MB, 78165360 sectors
wd1 at pciide1 channel 0 drive 1: <ST3250823A>
wd1: 16-sector PIO, LBA48, 238475MB, 488397168 sectors
wd0(pciide1:0:0): using PIO mode 4, Ultra-DMA mode 5
wd1(pciide1:0:1): using PIO mode 4, Ultra-DMA mode 5
wd2 at pciide1 channel 1 drive 0: <ST3250824A>
wd2: 16-sector PIO, LBA48, 238475MB, 488397168 sectors
wd2(pciide1:1:0): using PIO mode 4, Ultra-DMA mode 5
uhci0 at pci0 dev 31 function 2 "Intel 82801BA USB" rev 0x02: irq 3
"Intel 82801BA SMBus" rev 0x02 at pci0 dev 31 function 3 not configured
uhci1 at pci0 dev 31 function 4 "Intel 82801BA USB" rev 0x02: irq 10
isa0 at ichpcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
usb3 at uhci0: USB revision 1.0
uhub3 at usb3 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb4 at uhci1: USB revision 1.0
uhub4 at usb4 "Intel UHCI root hub" rev 1.00/1.00 addr 1
biomask ffed netmask ffed ttymask ffff
rd0: fixed, 3800 blocks
softraid0 at root
ahc0: target 2 synchronous at 10.0MHz, offset = 0xf
scsibus3 at softraid0: 1 targets
sd1 at scsibus3 targ 0 lun 0: <OPENBSD, SR RAID 1, 004> SCSI2 0/direct fixed
sd1: 238472MB, 512 bytes/sec, 488391923 sec total
root on rd0a swap on rd0b dump on rd0b
--
Christopher Linn <celinn at mtu.edu> | By no means shall either the CEC
System Administrator II | or MTU be held in any way liable
Center for Experimental Computation | for any opinions or conjecture I
Michigan Technological University | hold to or imply to hold herein.
